FORD FLTM BU 119-1-2000 INDUCTION CURE TEST FOR METAL BONDING ADHESIVES.pdf

1、 FORD LABORATORY TEST METHOD BU 119-01 Date Action Revisions 2000 12 01 Revised Editorial no technical change A. Cockman 1991 05 03 Printed copies are uncontrolled Page 1 of 7 Copyright 2000, Ford Global Technologies, Inc. INDUCTION CURE TEST FOR METAL BONDING ADHESIVES Application This method is us

2、ed to determine the adhesion strength characteristics of heat-cured metal bonding adhesives subjected to induction heating. Apparatus Required Induction Equipment Schematic Diagram - See Figure 1. Power Supply A 20 kW, 10 kHz, high frequency generator. Robotron #08001-04 or equivalent. Heat Station

3、Robotron 20 kW - 10 kHz heat station to match impedance load of coil to power supply. Inductor Fabricated as shown in Figure 2. Clamping Fixture Fabricated as shown in Figure 3. Temperature Pyrometer Temperature measurement instrument with capability of 23 30 C temperature range and +/- 3 C accuracy

4、. Ircon infra-red pyrometer or equivalent. Test Coupons Test coupons shall be 25 x 100 x 0.76 mm CRLC steel body stock or otherwise specified by the applicable Engineering Material Specification. Tensile Tear Machine Instron or equivalent with an accuracy of 0.5 % of the range used. Conditioning and

5、 Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. FORD LABORATORY TEST METHOD BU 119-01

6、 Page 2 of 7 Copyright 2000, Ford Global Technologies, Inc. Procedure 1. Prepare overlap shear test assemblies as shown in Figure 4. Use CRLC steel substrates unless otherwise specified in the applicable Engineering Material Specification. 2. Remove excess adhesive squeeze-out after coupon assembly

7、prior to positioning in induction clamping fixture. 3. Mount test assembly in clamping fixture, then induction heat at a schedule of 160 +/- 2 C, or as specified by the engineering document, for 4 s. Power and temperature curves representing this schedule are shown in Figure 5. 4. Condition bonded t

8、est assemblies to 23 +/- 2 C, then conduct shear pull test at a rate of 13 mm per minute. 5. Report peak load and type of separation (i.e., “adhesive“: adhesive to substrate separation; “cohesive“: separation within the adhesives). Chemicals, materials, parts, and equipment referenced in this docume

9、nt must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BU 119-01 Page 3 of 7 Copyright 2000, Ford Global Technologies, Inc. INDUCTION CURE TEST FOR METAL BONDING ADHESIVES Figure 1 Equipment Schematic FOR

10、D LABORATORY TEST METHOD BU 119-01 Page 4 of 7 Copyright 2000, Ford Global Technologies, Inc. INDUCTION CURE TEST FOR METAL BONDING ADHESIVES Figure 2 Inductor FORD LABORATORY TEST METHOD BU 119-01 Page 5 of 7 Copyright 2000, Ford Global Technologies, Inc. INDUCTION CURE TEST FOR METAL BONDING ADHES

11、IVES Figure 3 Clamping Fixture FORD LABORATORY TEST METHOD BU 119-01 Page 6 of 7 Copyright 2000, Ford Global Technologies, Inc. INDUCTION CURE TEST FOR METAL BONDING ADHESIVES Figure 4 Test Coupon Assembly FORD LABORATORY TEST METHOD BU 119-01 Page 7 of 7 Copyright 2000, Ford Global Technologies, Inc. INDUCTION CURE TEST FOR METAL BONDING ADHESIVES Figure 5 Power and Temperature Curves