ImageVerifierCode 换一换
格式:PDF , 页数:6 ,大小:37.27KB ,
资源ID:749006      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-749006.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD WSB-M2G316-B-2009 ADHESIVE FAST MOISTURE CURING URETHANE ONE COMPONENT HIGH VISCOSITY TO BE USED WITH FORD WSS-M99P1111-A 《高粘度单组分快速湿固化氨基甲酸酯胶粘剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(吴艺期)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD WSB-M2G316-B-2009 ADHESIVE FAST MOISTURE CURING URETHANE ONE COMPONENT HIGH VISCOSITY TO BE USED WITH FORD WSS-M99P1111-A 《高粘度单组分快速湿固化氨基甲酸酯胶粘剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 03 13 Revised See Summary of Revisions M. Mehandru, FNA2007 04 19 Revised Inserted 2.1, 5.1.4, 5.1.5 triangle form, 9 mm base and 13 mm height) of material under test to a 125 x 75 x 4 mm primed float glass specimen and check for correct

2、weight of applied bead of adhesive. For application temperature of material under test see Engineering Material specification. 2 min after application assemble with a 200 x 200 primed glass plate to a bead thickness of 4mm and fix in that position for 10 s. Remove distance spacers and turn assembly

3、to vertical position and fix one glass plate, add a weight to lower glass specimen to a total weight force of 8 N and measure the slippage after 2 h. Record all details of measurements and material under test. 3.3 CURE RATE PROPERTIES 3.3.1 Tack Free A 150 mm long and 6 mm diameter bead shall be tac

4、k free in 30 minutes and cured after 72 h at R.T. Apply beads of adhesive to a clean float glass panel. Touch the bead gently using a cotton swab for tack free test. Cut the bead using a sharp razor blade for curing test. 3.3.2 Sandwich Tensile Pull Strength Versus Cure Time, min Cure Time Sandwich

5、Tensile Pull Strength 1.5 hours 240 kPa 3.0 hours 517 kPa 6.0 hours 1.37 MPa 24.0 hours 2.5 MPa 72.0 hours 2.5 MPa ENGINEERING MATERIAL SPECIFICATION WSB-M2G316-B Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 4 of 6 Test Method: Sandwich Tensile Pull Strength . P

6、repare a minimum of 3 sandwich assemblies for each cure time tensile pull strength test as per Figure 1. . Brush apply metal primer onto painted coupon substrates in area where adhesive is to be applied. Condition the applied primer at R.T. for 30 minutes min, check the process standard for the max

7、open time. Brush apply glass primer or primers onto bottom 6.4 mm of each glass coupon according to the process standard of the primer or primers. Allow primer to air dry. Condition primer at R.T. for 5 minutes min check the process standard for the max open time. . Apply a 50 mm long by 6.4 mm diam

8、eter bead of adhesive to the primed glass, as illustrated in Figure 2. Within 5 minutes after adhesive application, position the adhesive on the glass coupon in contact with the primed metal surface. Maintain a 5 mm nominal adhesive bondline thickness. . Condition assemblies same at R.T. for various

9、 cure times as indicated above. . Determine the adhesion in a tensile machine having a jaw separation rate of 25 mm/minutes. Report strength value and mode of failure. 3.4 CURED ADHESIVE PROPERTIES 3.4.1 Flexibility (ASTM F 147, except condition at 150 mm long x 25 mm wide x 2.5 mm thick sample for

10、120 h at R.T., and then 4 h at the following temperatures) . 23 +/- 2 C No crack on 3 mm mandrel . -29 +/- 1 C No crack on 25 mm mandrel 3.4.2 Hardness, Durometer “A“ 60 +/- 5 Test Method: Flow enough material into a container (such as an ointment tin) to give a cured section 5 mm thick. Cure for 72

11、 h at R.T. and check the instantaneous hardness. 3.4.3 Tensile Properties (ASTM D 412, except where noted, use Type C die and pull at 50 cm/minute, cure on release paper between 3 mm aluminum panels for 7 days at 23 +/- 2 C and 50 +/- 5% relative humidity or as recommended by the material manufactur

12、er to achieve full cure. Condition at 23 +/- 2 C for 24 h, report at 23 +/- 2 C, use extensometer or strain gage, test at -40, 23, 50 and 80 +/- 2 C) ENGINEERING MATERIAL SPECIFICATION WSB-M2G316-B Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 5 of 6 Tensile at b

13、reak, min 6.9 MPa Elongation at break, min 200% Poissons Ratio 0.25 0.50 Modulus of elasticity (ASTM D 4065 or equiv. 10 MPa, min Report the value at 23 +/- 2 C, and 1 Hz) (Dynamic Mechanical Analyzer tensile compression mode) Frequency Sweep 0.1 to 100 Hz, fixed stress of 0.5% at 23 +/- 2 C. Temper

14、ature Sweep: -40 C to 100C, set heating rate to 2 C/min; fixed strain of 0.5% at 1 Hz frequency. Actual material properties are temperature and formulation dependent. Results are on file with Materials Engineering. 3.5 CURED MATERIAL PERFORMANCE PROPERTIES Parts and/or test samples prepared with mat

15、erials according to these specifications shall meet all requirements of performance specifications WSS-M11P57-A5. 3. 6 LINE TRIAL The Requirements defined in this specification are based upon laboratory coupon testing and define the minimum acceptance criteria for adhesive performance. Prior to use,

16、 the adhesive must be evaluated under the production parameters of the relevant production line. The choice of substrates, plant processing conditions and specific design application may affect adhesive performance. Compliance with this specification does not guarantee the adhesive will function for

17、 all potential applications on a vehicle. Therefore materials being evaluated for approval to this specification shall be subjected to a production trial. Functional trial results must be approved by the affected assembly operation. Results shall be made available to Materials Engineering prior to m

18、aterial approval and release. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 4.1 RELATED MATERIALS AND PROCEDURE 4.1.1 Glass Primer Wipe WSS-M5B280-C5 4.1.2 Adhesion Primer, Glass WSS-M2G314-B2 (Black

19、out primer) 4.1.3 Adhesion Primer, Painted Metal WSB-M2G234-C WSS-M2G234-C3 ENGINEERING MATERIAL SPECIFICATION WSB-M2G316-B Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 6 of 6 4.2 SUBSTRATES 4.2.1 Metal Substrate: Prior to releasing to this specification, the ad

20、hesive must be tested to painted steel panels of nominal thickness 0.80 mm. The substrate must be painted with all of the production paint systems that are currently being used by the assembly plant. 4.2.2 Float Glass: 5.6 mm nominal thickness. 4.2.3 Float Glass with WSS-M99P6-C1/C2 Ceramic Coating:

21、 4.3 WEIGHT PER VOLUME, Typical 1.15 1.30 kg/L (Refer to para 3.2.4) 5. SUMMARY OF REVISIONS 2009 03 13 1. Updated 2.1 and deleted Table 1. 2. Revised Storage Stability. 3. Added 3.5 Cured Material Performance Properties. 4. Revised 4.1 to reflect the new specification for Glass primers. 5. Title and Scope updated 6. Added FLTM to 3.2.2 Solid and 3.2.3 Ash 7. Updated 3.2.8 Odor and 3.2.9 Fogging 8. Added tests 3.2.12 Slippage 9. Deleted 3.4.2 Tear Strength 10. Changed Numbering.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1