ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:30.31KB ,
资源ID:749239      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-749239.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD WSB-M7H53-A-2010 WEBBING POLYESTER INTERNATIONAL TWILL SAFETY BELT TO BE USED WITH FORD WSS-M99P1111-A 《安全带用国际斜纹聚酯织带 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(bonesoil321)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD WSB-M7H53-A-2010 WEBBING POLYESTER INTERNATIONAL TWILL SAFETY BELT TO BE USED WITH FORD WSS-M99P1111-A 《安全带用国际斜纹聚酯织带 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Release No. Released 2010 03 04 N-STATUS No replacement named L. Sinclair, NA 1994 11 22 NB00I10043054398 Released D.Henrickson AJS WP 3948-a Page 1 of 5 WEBBING, POLYESTER, INTERNATIONAL TWILL, SAFETY BELT WSB-M7H53-A NOT T

2、O BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a polyester seat belt webbing woven with untwisted continuous filament yarn and finished selvages. Proper dyes and dyeing procedures shall be employed to provide acceptable colors, appearance, and physical properties. A

3、surface finish may be applied to enhance abrasion resistance. Color stripping for redyeing of webbing rejected for color is not allowed. The webbing shall be of good quality and uniform construction. 2. APPLICATION This specification was released originally for material used for metal to metal type

4、seat belts on the 1996 Mark VIII. 3. REQUIREMENTS Test Method Procedures: All webbing properties denoted by shall be tested in accordance with Federal Motor Vehicle Safety Standard No. 209. DE requirements listed in any of the following paragraphs are intended as maximum target values. Visual rating

5、s will take precedence. 3.1 STATISTICAL PROCESS Suppliers must conform to the requirements of Ford Quality System Standard Q-101. A mutually acceptable Control Plan as described therein is required for material/source approval. Appropriate statistical tools must be used to analyze process/product da

6、ta so that variation in the final product is continuously reduced. 3.2 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 48-67 % relative humidity for not less than 24 h prior to testing and tested under t

7、he same conditions unless otherwise specified. ENGINEERING MATERIAL SPECIFICATION WSB-M7H53-A WP 3948-b Page 2 of 5 3.3 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. Note: This web

8、bing is to be manufactured with a broken 2/2 twill herringbone pattern 3.4 THICKNESS 1.22 +/- 0.05 mm (SAE J882) 3.5 WIDTH Measured at less than 22 N load 3.5.1, min 45.75 mm 3.5.2, max 48.00 mm Measured at 9 790 N load 3.5.3, min 45.75 mm 3.6 COMPOSITION (ASTM D 629) Polyester 100 % 3.7 WEIGHT 5.5

9、- 6.1 kg/100 m 3.8 BREAKING STRENGTH, min 27 140 N 3.9 ELONGATION, max 8 % at 11 120 N 3.10 RESISTANCE TO LIGHT, min 87 % of original (Retained breaking strength after 100 breaking strength weatherometer hours exposure without water spray) 3.11 RESISTANCE TO HEX BAR ABRASION, min 77 % of original (R

10、etained breaking strength after 5 000 breaking strength abrasion strokes - 2 500 cycles) 3.12 RESISTANCE TO BUCKLE ABRASION, min 20 560 N (Retained breaking strength after 5 000 abrasion strokes - 2 500 cycles) ENGINEERING MATERIAL SPECIFICATION WSB-M7H53-A WP 3948-b Page 3 of 5 3.13 RESISTANCE TO F

11、ADE (AATCC Evaluation Procedure 1) 3.13.1 Weatherometer, min (max) Rating 3 (100 h without water spray) (3.4 DE) 3.13.2 Xenon Arc, min (max) Rating 3 (SAE J1885, 225.6 kJ/m2) (3.4 DE) No individual yarn or combination of yarns shall fade, stain or exhibit any color tone change, nor shall the yarns c

12、hange in hue or brightness in excess of the above ratings. 3.14 COLORFASTNESS TO CROCKING, WET AND DRY, min (max) Rating 4 (4.3 DE) Note: Instrumental reading to be determined per FLTM BN 107-02, AATCC Evaluation Procedure 2. 3.15 COLORFASTNESS TO STAINING-BLEEDING, min (max) Rating 4 (FLTM AN 101-0

13、1, AATCC Evaluation (4.3 DE) Procedure 2) 3.16 PERSPIRATION, min (max) Rating 4.5 (FLTM AN 101-01, AATCC Evaluation (2.2 DE) Procedure 2) 3.17 SPOTTING, min (max) (FLTM AN 101-01, AATCC Evaluation Procedure 2) 3.17.1 All colors - Water Rating 5 (1.8 DE) 3.17.2 For Light Colors Only Coffee Rating 5 (

14、1.8 DE) Soap Solution (25 % Lux or Rating 5 equivalent) (1.8 DE) Motor Oil (SAE 30 W) Rating 5 (1.8 DE) Colors designated light or mutually agreed to by the supplier and Body Engineering must meet this spotting requirement. ENGINEERING MATERIAL SPECIFICATION WSB-M7H53-A WP 3948-b Page 4 of 5 3.18 SO

15、ILING AND CLEANABILITY (FLTM BN 112-02) The performance of production material shall be equal to or better than that exhibited by the sample originally approved for production by the Materials Engineering Activity. 3.19 PLIABILITY (FLTM BN 102-05) 3.19.1 Lateral (fill) direction 350 - 800 units The

16、webbing when flexed and tested with the prescribed weight shall have the above reading of 350 - 800 units on the dial indicator face. Use a total of 50 g weight. Moving parts of the dial indicator add up to 20 g, that is, add a 30 g weight on top of the indicator. Note: Lateral pliability requiremen

17、ts, within the above range, may vary depending on individual vehicle system needs. Functional approval must be obtained from the releasing Car Program Management or Restraints Engineering office and submitted to Materials Engineering before approval will be given to this specification. 3.19.2 Longit

18、udinal (warp) direction, max 130 mm 3.20 FOGGING (Initial certification only for each color) (FLTM BO 116-03, 3 h at 100 +/- 2 C) Fog Number, min 60 Formation of a clear film, droplets or crystals is cause for rejection. 3.21 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute 3.22 ADDITIO

19、NAL REQUIREMENTS Specific requirements for material and or manufactured parts shall be specified on the engineering drawing, Engineering parts specification and/or performance specifications. All critical areas with respect to these properties shall be designated on the Engineering drawing. 3.23 SUP

20、PLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. ENGINEERING MATERIAL SPECIFICATION WSB-M7H53-A WP 3948-b Page 5 of 5 Prior to making any changes in the properties, composition, co

21、nstruction, color, processing or labeling of the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify Purchasing, Toxicology and the affected Materials Engineering activity of

22、 the proposed changes and obtain the written approval of the Materials Engineering activity. Test data, test samples and a new code identification are to be submitted with the request. Substance restrictions imposed by law, regulations or Ford apply to the materials addressed by this document. The r

23、estrictions are defined in Engineering Material specification WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification must have prior approval by the responsible Materials Engineering activity. Suppliers desiring approval of their materials shall first obtain an expression

24、of interest from the affected Purchasing, Design and Materials Engineering activity. Upon request, the Supplier shall submit to the affected Materials Engineering activity a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, dem

25、onstrating full compliance with all the requirements of this specification (test results, not nominal values), the material designation and code number, and test specimens for Ford evaluation. Fords engineering approval of a material will be based on its performance to this specification and on an a

26、ssessment of suitability for intended processes and/or applications. Upon approval, the material will be added to the Engineering Material Approved Source List. 5. GENERAL INFORMATION 5.1 INSTRUMENTED COLOR READINGS The instrument used for color difference measurements shall be either a spectrophotometer or a tristimulus colorimeter, and shall be capable of providing the following: Geometry 0/45 Observer 10 degree Specular Reflectance In (if an option) Illuminant D 65 Sample port size 25 mm (unless specified otherwise in test method)

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1