FORD WSD-M15H62-A-2009 THREAD POLYAMIDE THREE PLY TO BE USED WITH FORD WSS-M99P1111-A 《三股聚酰胺线 与标准FORD WSS-M99P1111-A一起使用 ［使用 FORD WSS-M8P5-C］》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Release No. Released 2009 07 20 N-STATUS Replaced by WSS-M8P5-C L. Schmalz, NA 1994 03 04 C10383750 Released N. Komatsu WP 3948-a Page 1 of 3 THREAD, POLYAMIDE, THREE PLY WSD-M15H62-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE T

2、he material defined by this specification is a polyamide thread manufactured as a single cord incorporating two separate plies. 2. APPLICATION This specification was released originally for material used as sewing thread for ruching operations in the manufacture of automotive seat or trim assemblies

3、 or as specified on the Engineering Drawing. 3. REQUIREMENTS In addition to the requirements quoted herein, this material must meet the requirements of the Performance Specification, WSD-M8P5-B. 3.1 STATISTICAL PROCESS Suppliers must conform to the requirements of Ford Quality System Standard Q-101.

4、 A mutually acceptable Control Plan as described therein is required for material/source approval. Appropriate statistical tools must be used to analyze process/product data so that variation in the final product is continuously reduced. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS Ford Mo

5、tor Company, at its option, may conduct infrared and/or thermal analysis of material/parts supplied to this specification. The IR spectra and thermogram established for initial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All sampl

6、es shall produce IR spectra and/or thermograms that correspond to the reference standard when tested under the same conditions. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative hum

7、idity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. ENGINEERING MATERIAL SPECIFICATION WSD-M15H62-A WP 3948-b Page 2 of 3 3.4 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or

8、 shall be as specified on the Engineering Drawing. 3.5 YARN CONSTRUCTION AND DESCRIPTION (ASTM D 1244) The thread is manufactured from two separate ends of 23.5 tex f 34 multifilament, bright, high tenacity Polyamide 6.6 yarn. These are twisted together in reverse (Z) direction. 3.6 PHYSICAL REQUIRE

9、MENTS 3.6.1 Thread Size, range 53 +/- 7 tex (FLTM BN 150-01) 3.6.2 Tensile Strength, min 28 N (FLTM BN 150-01, 125 mm/minute) 3.6.3 Elongation at Break, range 15 - 26 % (FLTM BN 150-01, 125 mm/minute) 3.6.4 Twist, range 350 - 550 turns/m (FLTM BN 150-01) 3.7 ADDITIONAL REQUIREMENTS Specific requirem

10、ents for material and/or manufactured parts shall be specified on the Engineering drawing, Engineering parts specification and/or performance specifications. All critical areas with respect to these properties shall be clearly designated on the Engineering drawing. 3.8 SUPPLIERS RESPONSIBILITY All m

11、aterials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. ENGINEERING MATERIAL SPECIFICATION WSD-M15H62-A WP 3948-b Page 3 of 3 Prior to making any change in the properties, composition, construction, color, processi

12、ng or labelling of the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify Purchasing, Toxicology and the affected Materials Engineering activity of the proposed changes and

13、obtain the written approval of the Materials Engineering activity. Test data, test samples and a new code identification are to be submitted with the request. Substance restrictions imposed by law, regulations or Ford, apply to the materials addressed by this document. The restrictions are defined i

14、n Engineering Material Specification WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification must have prior approval by the responsible Materials Engineering activity. Suppliers desiring approval of their materials shall first obtain an expression of interest from the affe

15、cted Purchasing, Design and Materials Engineering activity. Upon request, the Supplier shall submit to the affected Materials Engineering activity a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full complianc

16、e with all the requirements of this specification (test results, not nominal values), the material designation and code number, and test specimens for Ford evaluation. Fords engineering approval of a material will be based on its performance to this specification and on an assessment of suitability

17、for intended processes and/or applications. Upon approval, the material will be added to the Engineering Material Approved Source List. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of the specification. 5.1 FINISH 9.5 +/-

18、 3 % The finish shall consist of hard polyamide resin as a bonding agent and a suitable lubricant, e.g., a polyethylene and silicone type. The primary criterion for acceptability of the finish shall be the threads sewability. Finish content outside this range may be considered acceptable providing that the amount of lubricant or resin does not adversely affect the sewability performance or yield of the thread. 5.2 PUT UP Nominal Length per Spool 5000 m Alternative lengths may be supplied to suit manufacturing requirements.