GMKOREA EDS-T-2213-2016 Durability Test of the COG (Center of Gravity) Wheel Bearings (Version 4 English Do Not Use on New Program No Replacement).pdf

1、 ENGINEERING STANDARDS Test Procedure LIMITED USE EDS-T-2213 Durability Test of the COG (Center of Gravity) Wheel Bearings Do Not Use on New Program; No Replacement. Durability Test of the COG (Center of Gravity) Wheel Bearings , ( ). Copyright 2016 General Motors Company All Rights Reserved June 20

2、16 Originating Department: GM Korea Engineering Standards Page 1 of 2 Version : 4 1 Introduction Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of conflict between the Korean and English language, the Korean language shall take precedence. 1.1 Purpose.

3、Determination of the service life of the COG wheel bearings for the different speeds. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. No2.3 Additional References. None 3 Reso

4、urces 3.1 Facilities. 3.1.1 Calibration. The test facilities and equipment shall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment may also be used. However, all measuring variables as specified in this standard shall be

5、determined correctly with respect to their physical definition. 3.2 Equipment. 3.2.1 Twin Test Bench for transmissions, with electric-motor drive. 3.2.2 Temperature Control Device. 4 Procedure 4.1 Preparation. 4.1.1 Measure bore diameters of the COG wheels and shaft diameters of the bearing surfaces

6、 and their surface roughness. 4.1.2 Install the measured parts into the transmission. 4.1.3 Mount the transmission assembly on the test bench and shift into the gears required to obtain the maximum relative speed (highest and lowest gear ratio in the transmission). 4.1.4 Fill in specified amount and

7、 type of oil. 4.2 Conditions. 4.2.1 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. GM KOREA ENGINEERING STANDARDS EDS-T-2213 Copyright 2016 General Motors Com

8、pany All Rights Reserved June 2016 Page 2 of 2Version : 4 4.3 Instructions. 4.3.1 The speed at the transmission input is 6,000 min-1. 4.3.2 The maximum speed differences of the COG wheels compared with the main shaft are reached: At highest gear with transmission in lowest gear. At lowest gear with

9、transmission in highest gear. 4.3.3 The transmission runs at no load. 4.3.4 The oil temperature is held between 353 K (= +80 ) and 393 K (= +120 ) with the temperature control device. 4.3.5 After termination of the test, the bearings are to be measured per clause 4.1.1 and the wear is to be determin

10、ed. 5 Data 5.1 Bogy. 5.1.1 The number of test runs shall be at least 6. 5.1.2 Minimum running time 200 hours, 100 hours in highest and lowest (forward-) speed each, without damage of the bearing surfaces. 6 Safety This standard may involve hazardous materials, operations, and equipment. This standar

11、d does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2

12、Acronyms, Abbreviations, and Symbols. COG: Center of Gravity 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to EDS-T-2213 9 Release and Revisions This standard was originated in July 1996. It was first approved by Engineering Standard Committee in July 1996. It was first published in July 1996. Issue / Publication Date/ Description (Organization) / / () 3 JUL 2015 5 year refresh and revised to current template. (TM Test & Validation PMT Team) 5 . ( ) 4 JUN 2016 Limited use with no replacement (TM Test & Validation PMT Team) / ( ) ( )