GMKOREA EDS-T-4558-2011 Test Procedure of Seat Cushion Tilting Operation Durability.pdf

1、 ENGINEERING STANDARDS Test Procedure SUPERCEDED EDS-T-4558 Test Procedure of Seat Cushion Tilting Operation Durability This standard may be applied only for current projects. It is Superceded for all future projects and replaced by GMW14519. Seat Cushion Tilt 98 ! 4G 98 88x 7 , F6* 72T8p) F$ . 1.1

2、+95 . Seat Cushion Tilt 98 4 Tilt Mechanism ! 2e G88x +958p) F$ . 1.2 957 -88 . Seat Cushion Tilt Mechanism8 .=%P +& seat7 957F$ . 2 4) E:4 / :0 : C-H +d%P 9I8 6# F 48 07 38%P E:48x 957F$ . 2.1 17 E:4 / . None 2.2 GM E:4 / . None 2.3 dA E:4 / . None 3 4G 88 3.1 4G 8/x . 3.1.1 B.I.W (Body in White) D

3、# SEAT* 4= M8 9IF 3L 8# Jig. 3.1.2 98! 4G d . 3.1.3 Cushion Pan (Weight 68 Kg). 3.2 4G D . 4E ASSY1B8 Seat* 3P 81 4G F$ . GM KOREA ENGINEERING STANDARDS EDS-T-4558 Copyright 2011 General Motors Company All Rights Reserved September 2011 Page 2 of 3 Version : 3 4 Procedures 4.1 Conditions. 4.1.1 Test

4、 Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.2 Instructions. 4.2.1 Fit the BIW or the seat-fixing jig on the durability tester, and then mount a seat on the B

5、IW or the jig. 4.2.2 Set the seat adjuster systems other than the seat cushion tilt to the position specified in the design standard. 4.2.3 Load the cushion pan with weight of 68 kg on the seat cushion. 4.2.4 Adjust the position of the weight of the cushion pan to be concentrated on the H-point. 4.2

6、.5 Move the seat cushion from the uppermost position to the lowermost position with the adjuster knob as shown in Figure 1. 4.2.6 Return the seat cushion from the lowermost position to the uppermost position with the adjuster knob. 4.2.7 Repeat the test for 10,000 cycles in a speed of 5 10 cpm. Each

7、 cycle consists of the procedures defined in items 4.2.4 and 4.2.5. 4.2.8 If the seat cushion tilting mechanism is of independent forward and backward mechanism, repeat the test for 10,000 cycles in forward and backward direction respectively. 4 4G 9 F$72P 1$8p) 8% 4A$ . 4.2.6 Adjuster Knob* 87F7 Se

8、at Cushion8x 1$72P F$8p) 8% 4A$ . 4.2.7 4.2.4 4.2.5* 1cycle) F7 5 10 cpm8 2$) 10,000cycle* 44F$ . 4.2.8 98 , G $*4 Mechanism8 7 98 , G 55 10,000 Cycle8x 44F$ . Figure 1 / ,* 1 GM KOREA ENGINEERING STANDARDS EDS-T-4558 Copyright 2011 General Motors Company All Rights Reserved September 2011 Page 3 of

9、 3 Version : 3 5 Data 5.1 Evaluations. 5.1.1 There shall be no abnormal noise after the durability test. 5.1.2 The functions throughout the zones shall be free of abnormal operation after the durability test. 5.1.3 There shall be no transformation or damage hazardous for passengers. 6 Safety This st

10、andard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of

11、regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. Not applicable. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to EDS-T-4558 9 Release and Revisions This standard was originat

12、ed in October 1998. It was first approved by Engineering Standard Committee in October 1998. It was first published in October 1998. 5 4G $8Bd 5.1 D4 . 5.1.1 ! 4G G 888 68x . 5.1.2 ! 4G G 98 8 d#7 818 68x . 5.1.3 ! 4G G 387 8TFF -GI -C D28 68x . 6 6|987 $4F 7 9 ., E:48t 88G ,p: , 86 , 8/x &%8x E FF

13、3L 8$ . ., E:48t 87 $4F 170 4)%P +& 6|98 ,l9P8 F8x 9P4F:# 6#$ . &d(2P 17 987 95FF 6|980 I 1B* 9DF , -18 9PF 728 957 7 .* 9IF# 8t ., E:4 1788 =y8 1F8$ . 7 768 9I8 7.1 98,l 76 . F$-1F 68 . 7.2 66 -C dGl . F$-1F 68 . 8 Ed - $* ,l2P! $+ &%72P ., E:48 87%T &# $80 M8 EdF$ . Test to EDS-T-4558 9 9P9I -C P9

14、I 8)Y ., E:48t 1998“x 1087 E:4 -Gl4 .7 %L6 , d3TE:41,h7 8F 1998 “x 10 87 38%L6$ . ., E:48t 1998 “x 10 87 ) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 3 SEP 2011 Apply new Engineering Standard Template. Superceded (Interior Subsystem Validation Team) / 4 d3TE:4 64 957 . F9I957 =* (Interior.ED4D4 )