ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:49.35KB ,
资源ID:757116      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-757116.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(GMKOREA EDS-T-5216-2008 SUPPRESSOR PLUG IGNITION LEAD.pdf)为本站会员(孙刚)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

GMKOREA EDS-T-5216-2008 SUPPRESSOR PLUG IGNITION LEAD.pdf

1、GM DAEWOO Auto & Technology EDS Engineering GM DAEWOO Auto & Technology Standards SUPPRESSOR PLUG, IGNITION LEAD Do Not Use on New Programs. Being Replaced by GMW3172 EDS-T-5216 ISSUED DATE: 1984. 10. 02 REVISED DATE: 2008. 10. 27 VERSION: 3(Superceded) EDS-T-5216SUPPRESSOR PLUG, IGNITION LEAD PAGE:

2、 1/4 ISSUED DATE: 1984. 10. 02 REVISED DATE: 2008. 10. 27 VERSION: 3 GM DAEWOO Auto & Technology Note: This standard may be applied only for current project (incl. T255 Program). It is Superceded for all future projects and replaced by GMW3172. 1. PURPOSE The purpose of this specification is it, to

3、define the suppressing effect (HF - damping) as well as the physical, electrical and endurance tests on suppressor plugs, ignition lead. 2. QUANTITY OF TEST SAMPLE For the laboratony release tests of prototypes, 16 samples - suppressor plug are required. For the endurance test in the car, min. 24 pa

4、rts are necessary. The proposed test sequence and the quantity of test samples for every test is given in Blatt 3. 3. QUALITY CHECK For the supervision of the production quality and the satisfaction of this specification, the Dpt. Inspection & Quality control is responsible. 4. VISUAL TEST The suppr

5、essor plugs must be free from damages and foreign bodies in the state as supplied. 5. PHISICAL TEST The suppressor plugs must correspond to the definitions and specifications on the drawing in the dimensions and other physical properties. All units of measure are to be given in SI - units (System In

6、ternational), as they were discharged of the International Standards Organization. The value of resistor suppressor is to be given on the drawing. If nothing different is given, all tests are to be perfromed at tr (+23 5K). 5.1. Sounduess 5.1.1. Equip 4 suppressor plugs with 65 cm long, serial ignit

7、ion leads, air - vent protectors and spark - plug mock - up. 5.1.2. Store asm. over 144 h at +90 2.5K and immediately after then 1 h at +120 2.5K. EDS-T-5216SUPPRESSOR PLUG, IGNITION LEAD PAGE: 2/4 ISSUED DATE: 1984. 10. 02 REVISED DATE: 2008. 10. 27 VERSION: 3 GM DAEWOO Auto & Technology 5.1.3. Coo

8、l assembly down to tr (+23 5K). 5.1.4. Draw off suppressor plug, from the spark plug and insert it again 10 times. 5.1.5. Draw off lead and air - vent protector from the suppressor plug and insert it again 5 times. 5.1.6. The aged parts are to be so installed into a receptacle that all sealing point

9、s are immersed at the following filling with a 10% saline solution. 5.1.7. 7 cm from the edge of the air - vent protector, a shaking device embraces the ignition leads and moves these with an amplitude of 6 mm and 25 . 5.1.8. At a voltage of 20 KV put to the ignition leads of an ignition coil or an

10、equivalent voltage source (earthing potential in the water), at an impulse frequency of 20 , break - down or break - off may not occur within a testing time of 2 h. 5.2. Aging test (at high rel. air humidity) 5.2.1. The plug connector is to be equipped with a 11 cm long ignition lead (copper lead) a

11、nd air - vent protector. 5.2.2. The plug connector asm. is inserted to a spark - plug mock - up, which is screwed into a metal plate. The spark - plug mock - up is distinguished from a normal spark plug only in the absent center electrode. 5.2.3. A temperature - stabilized ignition coil or an equiva

12、lent voltage surce is adjusted to 20 KV (impulse frequency 20 ) at open circuit and then connected to the free, bare end of the ignition lead. The metal plate, into which the spark plug is screwed, is connected with earth connection. The voltage is to be measured. 5.2.4. Store plug connector 10 min

13、in cooling chamber at -20 3K. 5.2.5. Take plug connector out of the cooling chamber and immediately store 23 h 50 min in air - conditioning cabinet at +40 2.5K and 97% 1 % rel. air humidity. (If it permits the arrangement, it is to be adjusted to the higher limit value). 5.2.6. The points 5.2.4 and

14、5.2.5 are repeated 12 times. This results a total testing time of 288 h. 5.2.7. The point 5.2.3 is repeated per workday (6h after cold storage), while the test sample remains in the air - conditioning chamber. 5.3. The measured voltage may never come to less than 10 KV.EDS-T-5216SUPPRESSOR PLUG, IGN

15、ITION LEAD PAGE: 3/4 ISSUED DATE: 1984. 10. 02 REVISED DATE: 2008. 10. 27 VERSION: 3 GM DAEWOO Auto & Technology 5.3 Aging test with regard to acid effect 5.3.1. Remove metal casing. 5.3.2. Provide insulation part in the lower range of the spark plug chamber with bore 1 and subsequently close this w

16、ith a pasted small silicon plate. 5.3.3. Store suppressor plug 2h at -20 3K. 5.3.4. Store cold part 15 min in air conditioning chamber at +40 2.5K and 97 % 1% rel. air humidity. 5.3.5. Close spark - plug - sided chamber with glass plate and suitable sealing compound hermetically. 5.3.6. The small si

17、licon plate is pierced with an injection needle and 2 L nitric oxyde N2O4(NO2) is injected. After the withdrawal of the injection needle the opening in the small silicon plate is thoroughly closed. 5.3.7. Store test setup (as described under 5.3.5) over 24h at +50 2.5K. 5.3.8. Remove glass plate and

18、 sealing. 5.3.9. In the demounted metal casing, cut out opening in the range of the bore in insulating part to avoid breakdown and mount metal casing. 5.3.10. Mount 10cm long ignition lead (copper core) and air - vent protector. 5.3.11. Store plug connector - ignition lead - air - vent protector asm

19、. in an air conditioning chamber at +40 2.5K and 97% 1% rel. air humidity. 5.3.12. After 0.5h the test sample is taken out of the air conditioning chamber and 20 KV is put from a temperature - stabilized ignition coil or an equivalent voltage source to the ignition lead (ignition impulse sequence =

20、20 ). The metal casing is connected with earth connection. 5.3.13. The measured drop in voltage may not come to more than 5 KV. 5.4. Damping Attenuation equivalent to VDE 0879, Pt. 1. Radio interference control equipment type B. 5.5. Temperature stability After 1 h storage at +160 2.5K and following

21、 cooling down to tr (+23 5K), the plug connection must still satisfy all requirements of this specification. 5.6. Withdrawal force The force which is required to draw off the plug connector from the spark plug, must come to (60 20)N. 5.7. Plug - in force The force, which is required to plug in the p

22、lug connector to the spark plug, may come to max. 150 N. EDS-T-5216SUPPRESSOR PLUG, IGNITION LEAD PAGE: 4/4 ISSUED DATE: 1984. 10. 02 REVISED DATE: 2008. 10. 27 VERSION: 3 GM DAEWOO Auto & Technology 5.8. Breakdown test Test setup as 5.2.1 and 5.2.2. A temperature - stabilized ignition coil or an eq

23、uivalent voltage source is connected to the free, bare end of the ignition lead and adjusted to 30 KV. The impulse frequency should come to 20 . Within a testing time of 10 min, breakdown or break - off may not occur. 5.9. Track resistance The plug connector should satisfy the requirements of DIN 53

24、480 KA 3 c. 5.10. Corrosion test The plug connector submits to a salt - spray test corresponding to the specifications of the ASTM. B-117 or an equivalent test. 5.10.1. The plug connector must be visually acceptable after 48 h according to a standard arranged between supplier and GMDAT TECHNICAL CEN

25、TER. 5.10.2. The plug connector may not show any defects after 144 h which might impain the function. 6. CAR The suppressor plugs must endure a range of action to be defined by the GMDAT TECHNICAL CENTER under normal traveling conditions without rejection in the car. If the supplier of suppressor plugs has to perform a test connected with it, this is to be specially arranged. After the test the suppressor plugs must still perfect in the function.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1