GMKOREA EDS-T-7018-2011 Paint Finishes.pdf

1、 ENGINEERING STANDARDS General Specification LIMITED USE EDS-T-7018 Paint Finishes Do Not Use on New Program; No Replacement. D8C 4G - Note: 8 E:48t G8 =97 FF7 957%L+ , FG P-P Program 72P# 957%L: 6#$ . Copyright 2011 General Motors Company All Rights Reserved July 2011 Originating Department: GM Kor

2、ea Engineering Standards Page 1 of 5 Version : 4 1 Introduction Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of conflict between the Korean and English language, the Korean language shall take precedence. 1.1 Purpose. This standard covers laboratory t

3、est requirements of paint finishes as commonly used for automobile components. 1.2 Scope. This standard shall be classified into 9 classes according to substrate and does not cover appearance requirements or processing parameters. 1.2.1 A336. Normally applicable to exterior cat parts having a corrod

4、ible substrate, such as unplated cold rolled steel, precoated steel, die cast zinc, aluminum or magnesium. 1.2.2 A168. Normally applicable to chassis suspension components having steel substrates. 1.2.3 A96. Normally applicable to exterior car parts having a bright substrate such as buffed stainless

5、 steel, chromium plated metal or plastic and anodized aluminum. 1.2.4 A0. Normally applicable to exterior car parts having plastic or other nonmetallic substrates. 1.2.5 B336. Normally applicable to chassis and/or under hood parts. 1.2.6 B168. Normally applicable to chassis and/or under hood parts.

6、1.2.7 B96. Normally applicable to chassis and/or under hood parts. 1.2.8 C24. Normally applicable to interior car parts having metallic substrate. 1.2.9 C0. Normally applicable to interior car parts having plastic or other non-metallic substrates. 2 References Note: Only the latest approved standard

7、s are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 1 P7 :0 : ., E:48 6&F !7$ :4-8! 9I8x $4=F 3L 6$ . :0 : F67t 7568 18 88x 7 , F6* 72T8p) F$ . 1.1 +95 . ., E:48t 8% =7 .E7 17%L# D8C8 4G - -C 7 $4F7 9IF 8$ . 1.2 957 -88 . ., 4G -8t 2:7 &d( $88 94: &%=8p) .*%L+ 07

8、 38%P E:48x 957F$ . 2.1 17 E:4 / . None GM KOREA ENGINEERING STANDARDS EDS-T-7018 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 2 of 5 Version : 4 2.2 GM Standards/Specifications. EDS-T-7005 EDS-T-7143 EDS-T-7508 EDS-T-7701 EDS-T-7730 EDS-T-7737 EDS-T-7745 EDS-T-7747 EDS-T

9、-7775 EDS-T-7780 GMW3059 2.3 Additional References. None 3 Test Preparation and Evaluation 3.1 Resources. 3.1.1 Calibration. The test facilities and equipment shall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment may al

10、so be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their physical definition. 3.2 Conditions. 3.2.1 Conditioning. Unless otherwise specified, painted samples shall be subjected to the testing after a minimum aging period of 72 hou

11、rs following the baking or drying cycle. A shorter aging period may be used, provided it is recognized that this represents a more severe condition of test and that results obtained at different aging times under 72hours are not a good basic for comparing the relative performance characteristics of

12、paint finishes. 3.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 3.3 Safety. This standard may involve hazardous materials, operations, and equipment. Thi

13、s standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 3.4 Documentation. Samples of com

14、ponents or material released to this standard shall be tested for conformity with the requirements of this standard and approved by the responsible GM Department prior to the start of delivery of production level components or materials. 2.2 GM E:4 / . EDS-T-7005 EDS-T-7143 EDS-T-7508 EDS-T-7701 EDS

15、-T-7730 EDS-T-7737 EDS-T-7745 EDS-T-7747 EDS-T-7775 EDS-T-7780 GMW3059 2.3 dA E:4 / . None 3 4G :4/x -C D4 3.1 4G 88 . 3.1.1 9I . 4G 2X/x7t 8/x# 9P 2e#8x -PHLF 8TGF 9I Fx:8x J66 F$ . 3.1.2 $4= 3L$ . $4= 4G 42X0 8/x4 17%T 3L 8$ . ,) ! ., E:47 +d%P +& ?U9I -3L&8t , ,p*95 9I87 8 9IGF 9I%L66 F$ . 3.2 8-

16、L 9 . 3.2.1 98=* 9 . $+ D# 8: 7 C-H +d%L6 8: 68t 7 !d 1B8 .E8x C-F 98=* 68 17F$ . $ , +& 4G D8t $80 9 G 72 48 8G7 4G %L66 F+ 2P) $* 7$72P 72 48 81 -?%P 4G D 87# 4G 08 1Gl /x* F2P# 6| %P$ . 3.2.2 4G 9 . .,E:48p).Bd-6!#7 1F8t $-188 F8F6 F+ , 4)$+ , 4G 2e952P , .(2P&%7$+d%L66F$ . 3.3 6|987 $4F 7 9 . .,

17、 E:48t 88G ,p: , 86 , 8/x &%8x E FF 3L 8$ . ., E:48t 87 $4F 170 4)%P +& 6|98 ,l9P8 F8x 9P4F:# 6#$ . &d(2P 17 987 95FF 6|980 I 1B* 9DF , -18 9PF 728 957 7 .* 9IF# 8t ., E:4 1788 =y8 1F8$ . 3.4 : 2P* 9P) . 8 E:47 8F 9P%P .E8! 8*8 4G D8t ., E:47 9I%P 4G 8x 7 98x +94P6 F+ , 61 )= 987 GM :04 .2P8 388x -O

18、6x6 F$ . GM KOREA ENGINEERING STANDARDS EDS-T-7018 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 3 of 5 Version : 4 Any change to the component or material, e.g., design, function, properties, manufacturing process and/or location of manufacture requires a new release of t

19、he product. It is the sole responsibility of the supplier to provide the customer, unsolicited, with documentation of any change or modification to the product/process, and to apply for a new release. If not otherwise agreed to, the entire verification test shall be repeated and documented by the su

20、pplier prior to start of delivery of the modified or changed product. In some cases, a shorter test can be agreed to between the responsible GM department and the supplier. 4 Requirements and Procedure .E8! 8*7 862P &H88 , d# , 22e , 9P9 )9I ,* /D# 21:7t 4)%P 6&F -8($ -P2%T 7 49PE 4* 7F$ . )=8# +88

21、7= 7 .7t 14 68 9PE /21 )9I 18 - Gm8t P97 4F 2P* 9P)F6 F+ 4 9PE 4 4=8x F6 F$ . $* F84 6# F , )=8# P9 Gm8t -%P 9PE8 )= 987 98= : 4G 8x -L.) 3LFF 0* ,l2PGF6 F$ . 8. 77 86 GM :04 .2P7t )=888 F87 8F $%P : 4G 8x 44F 3L 8$ . 4 7 9 -C 4G 9 1,000 Mpa). 4.8 (h): Minimum rating of 8 (flexural modulus 1,000 Mpa

22、). 4.9 (i): No evidence of brittleness. Paint removal shall be confined to an area less than the width of the furrow made by the dime. 4.10 (j): No marring or paint removal of the surface (i.e., no paint removal or change in appearance). 4.11 (k): Only a slight appearance change allowed on paint sur

23、face. Trace amount of paint allowed on cloth. 4.12 (l): Minimum rating of 8. 4.13 (m): Minimum of 8. 4.14 (n): No color or paint removal to previous surface or lifting or peeling of paint film. 4.15 (o): No visible defect in paint film. 4.1 (a): !E1B72P 99 % 818 D8C 8T:)Y8x .(8 . 4.2 (b): 9I%P 48 G

24、8U6| D4F7 .E8 D# , 78 -G 68x . 4.3 (c): 99 % 818 8T:)Y8x .(8 . 4.4 (d): Creep Back 3 mm 8!8 . 4.5 (e): -P=8 -884 10 % 8!8 (!$0 Greep Back .88 9P7 ). 4.6 (f): (? (Lacquer) Rating 5 81 7!+ (Enamel) Rating 6 81 , 1,000 Mpa). 4.8 (h): Rating 8 818 (Flexural Modulus 1,000 Mpa). 4.9 (i): ?2e (Brittleness)

25、 8 H95 68x . $8+8 -I*# % 98 (Dime)8 58t .887t % 8F “G8)+ F7F$ . 4.10 (j): 2B7 D8C H95 D# E+8p).Bd8 -I* 68x . 4.11 (k): -,2lF 748 -G F7 -C 8i8p)8 988 F7 . 4.12 (l): Rating 8 81 . 4.13 (m): 8 81 . 4.14 (n): D8C Fx*8 -I* , &(l0 -1 68x . 4.15 (o): D8C Fx*8 -G 68x . GM KOREA ENGINEERING STANDARDS EDS-T-7

26、018 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 5 of 5 Version : 4 5 Provisions for Shipping 6 Notes 6.1 Glossary. Not applicable. 6.2 Acronyms, Abbreviations, and Symbols. Not applicable. 7 Additional Paragraphs 7.1 All parts or systems supplied to this standard must co

27、mply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: EDS-T-7018 9 Release and Revisions This standard was originated in July 1991. It was first approved by Engineering

28、Standard Committee in July 1991. It was first published in July 1991. 5 2T957 $4F 9F 6 768 9I8 6.1 98,l 76 . F$-1F 68 . 6.2 66 -C dGl . F$-1F 68 . 7 .4 1F 7.1 ., E:47 9P4%P +& .E&0 43B8t GMW3059 (8TF,p: 179P )8 9P* &d(6 F$ . 8 Ed - $* ,l2P! $+ &%72P ., E:48 87%T &# $80 M8 EdF$ . EDS-T-7018 9 9P9I -C

29、 P9I 8)Y ., E:48t 1991 “x 7 87 E:4 -Gl4 .7 %L6 , d3TE:41,h7 8F 1991“x 787 38%L6$ . ., E:48t 1991“x 787 ) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 4 JUL 2011 Apply new Engineering Standard Template. Limited use with no replacement (Polymer / Organic Material Lab Team) / 4 d3TE:4 64 957 . F9I957 ($4=E:4 68 ) =* (G)8*4G D4 )