GMW GMW14780-2011 General HVAC Module Requirements Issue 2 English《一般HVAC模块的要求 第2次出版(英文版本)》.pdf

1、 WORLDWIDE ENGINEERING STANDARDS General Specification GMW14780 General HVAC Module Requirements Copyright 2011 General Motors Company All Rights Reserved December 2011 Originating Department: North American Engineering Standards Page 1 of 5 1 Introduction Note: Nothing in this standard supercedes a

2、pplicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Scope. Heating and air conditioning for the complete vehicle range. 1.2 Mission/Theme. This standard defines the general requirements, test condit

3、ions and test methods for function, material and static load tests for heating ventilation air conditioning (HVAC) modules for automotive applications. 1.3 Classification. General requirements and requirements for single components are defined in the following parts to this standard. GMW3079 Plenum-

4、HV/HVA Inlet Water Ingestion (Includes Dynamic Separation Test) GMW14139 Corporate Body Pressure Relief Valves, PRVs GMW14192 Condenser with Integrated Receiver Dryer Product and Test Procedure Specification GMW14319 Refrigerant Hose and Coupling GMW14321 Fuel Operated Heater: Auxiliary and Parking

5、GMW14322 Heater Core GMW14323 HVAC Particle Filter GMW14325 HVAC Air Ducts GMW14483 Vehicle Air Conditioning Compressor and HVAC System Noise and Vibration Evaluation Procedure GMW14718 Heating Unit, Air Conditioning Unit GMW14780 General HVAC Module Requirements GMW14787 HVAC Hybrid Filter, Particl

6、e and Odor GMW14788 Variable A/C Compressor GMW 14789 Fixed A/C Compressor GMW15259 Blower and Recirculating Air Housing GMW15448 Specification for Heating, Ventilation and Air Conditioning Air Outlets GMW16151 Air Conditioning System Evaporator GMW16154 Corporate Thermostatic Expansion Valve 2 Refe

7、rences Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ECE-R21 EN 10204 FMVSS 302 VDA 260 Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking p

8、ermitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14780 Copyright 2011 General Motors Company All Rights Reserved December 2011 Page 2 of 5 2.2 GM Standards/Specifications. GMW3059 GMW3232 GMW14322 GMW14788 GMW3079 GMW3235 GMW14323 GMW14789 GMW3091 GMW3286 GMW14325 GMW15259

9、 GMW3097 GMW14139 GMW14483 GMW15448 GMW3103 GMW14192 GMW14718 GMW16151 GMW3172 GMW14319 GMW14729 GMW16154 GMW3205 GMW14321 GMW14787 GMW16331 3 Test Preparation and Evaluation 3.1 Resources. 3.1.1 Calibration. The test facilities and equipment shall be in good working order and shall have a valid cal

10、ibration label. 3.1.2 Alternatives. Alternative test facilities and equipment may also be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their physical definition. 3.1.3 Facilities. 3.1.3.1 According to the stated standards, test me

11、thods, test specifications, etc. 3.1.3.2 Recirculating air cabinet: Temperature range: (-40 to +90) C Permissible temperature deviations: 3 C Usable interior space width height depth: (1.0 1.0 1.0) m (minimum). 3.1.3.3 Environmental chamber to test heating and air conditioning modules in high humidi

12、ty environments to GMW14729. Chamber dimensions width height depth: (1.0 1.0 1.0) m (minimum). 3.1.4 Equipment. Thermoelectric measuring instrument Directional Probe: (0.01 to 1) m/s and (0.01 to 5) m/s Omni directional Probe: (0.01 to 1) m/s and (0.01 to 5) m/s Humidity Probe: (0 to 99)% Temperatur

13、e Probe: (-20 to +60) C 3.1.4.1 According to the stated standards, test methods, test specifications, etc. 3.1.4.2 Instruments and gauges for dimensional checks. 3.1.4.3 Air volume flow meter (0 to 3) L/s. 3.1.4.4 Suitable blower to produce the following ram pressures: 600 Pa at a flow rate of 100 L

14、/s 400 Pa at a flow rate of 200 L/s 3.1.5 Test Vehicle/Test Piece. Not applicable. 3.1.6 Test Time. Not applicable. 3.1.7 Test Required Information. Not applicable. 3.1.8 Personnel/Skills. Not applicable. 3.2 Preparation. 3.2.1 Test Samples. Unless otherwise specified for initial sample approval and

15、 validation, test to this standard at least 5 components of the same type are required. The test samples shall be supplied with a test certificate to EN 10204. The delivery of further samples of the same type may be agreed. Copyright General Motors Company Provided by IHS under license with General

16、Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14780 Copyright 2011 General Motors Company All Rights Reserved December 2011 Page 3 of 5 3.3 Conditions. Unless otherwise specified in the relevant tests, the tests

17、 shall be performed in the as received condition at (23 5) C. 3.3.1 Environmental Conditions. Not applicable. 3.3.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports,

18、etc. 3.4 Instructions. Not applicable. 3.5 Data. Not applicable. 3.6 Safety. This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to e

19、stablish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 3.7 Documentation. Samples of components or material released to this standard shall be tested for conformity with the requirements of this standard and approved by the responsibl

20、e GM Department prior to the start of delivery of production level components or materials. Any change to the component or material, e.g., design, function, properties, manufacturing process and/or location of manufacture requires a new release of the product. It is the sole responsibility of the su

21、pplier to provide the customer, unsolicited, with documentation of any change or modification to the product/process, and to apply for a new release. If not otherwise agreed to, the entire verification test shall be repeated and documented by the supplier prior to start of delivery of the modified o

22、r changed product. In some cases, a shorter test can be agreed to between the responsible GM department and the supplier. 3.7.1 Test Results. The results of the tests shall be summarized in a test report. 3.7.2 Deviations from Test Procedure. Deviations from the requirements of the test procedures s

23、hall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4 Requirements and Procedure 4.1 General. 4.1.1 The single components shall comply with the safety requirements to ECE-R21. 4.1.2 Plastic and metal parts shall be free from burrs

24、in safety zones and areas which may cause injuries during installation and transport. 4.1.3 Electrical Tests. All electrical and electronic tests shall be examined to GMW3172. The coding is to be carried out from the individual parts of this standard. In case of missing information, coordination wit

25、h the release engineer is to be made. 4.1.4 Materials. All materials and surface treatments of components shall comply with the drawing specifications and release data and shall be selected to fulfill the loads during vehicle operation. Chlorofluorocarbon (CFC) - free foams only may be used for the

26、seals. 4.1.5 Identification. The following shall be easily legible and permanently attached to the components: GM trademark to GMW16331. Date of manufacture to GMW16331. Manufacturer (letter symbol) to GMW16331. Part number. Materials designation to VDA 260. 4.1.6 Test Temperature. Unless otherwise

27、specified, the tests shall be performed at (+23 5) C. 4.1.7 Installed Position, Test Position, Test Setup. The test position during the tests per this standard shall correspond with the drawing. During all tests having an influence on the function of the single components, the test setup shall corre

28、spond with vehicle installed position. 4.1.8 Odor. The odor characteristics of the air deflection parts shall fulfill the requirements to GMW3205, Rating 6 (minimum). Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking

29、 permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14780 Copyright 2011 General Motors Company All Rights Reserved December 2011 Page 4 of 5 4.1.9 Fogging. Test all single components to GMW3235- B - T1 2 mg (maximum). 4.1.10 Other Methods. On principle, other testing devic

30、es and test methods are also permissible as long as they assure that the parameters stipulated in the requirements are correctly recorded. 4.1.11 Test Medium. Unless otherwise specified, a mixture of 50% water and 50% antifreeze concentrate by volume to the released coolant shall be used as test med

31、ium. 4.2 Visual and Dimensional Inspections. In the as received condition the single components shall not have any visible damages and defects which can impair their function or appearance. Dimensions of heating modules, air conditioning modules and heater cores shall be within the tolerance ranges

32、specified on the drawings and/or releases. Bearing surfaces shall be lubricated. 4.3 Leak Tests. 4.3.1 Air Leak Tests. Within a temperature range from -30 C to +60 C, the single components shall comply with the following requirements: Allowed air leak rate: Heater flaps: 1 L/s Temperature flap: (in

33、full cold and full hot): 1 L/s Ventilation flap: 1 L/s Defrost flap in Air Conditioning mode: 0.5 L/s Recirculating flap: 1 L/s Housing/Joints: 1 L/s Blower Motor Joint: 1 L/s Blower Control Interface: 0.5 L/s Connector interface: 0.5 L/s Test Pressure: 250 Pa Test Range: 50 Pa steps over the range

34、Allowed air leak rate: Tolerance for all doors is 0.3 L/s Note: No spot leaks are allowed in the Defrost outlet area on the HVAC Module bench test. Air leak valid for the complete defrost opening to the defrost nozzle interface. Air leak velocity lower than 0.3 m/s on the defrost flange outlet at ma

35、ximum pressure (250 Pa). The test shall be performed on the assembly with the related control unit. 4.3.2 Immersion Test. Components which are required to be 100% leakproof shall be tested as follows: Connect compressed air or vacuum supply to an opening or hose connection. Seal all other openings a

36、irtight, immerse component to be tested in water and apply the test pressure. During the over pressure test no bubbles shall occur during the test time of 1 minute. The test pressure is indicated in the drawing or is three times the operating pressure. The under pressure test is made in the open atm

37、osphere. Test pressure is -80 kPa. After this test, the parts shall be fully functional. 4.4 Noise Test. On the single components and on the assembly of vehicle heating and air conditioning, disturbing noise as rattle, scrape, squeal, whistle, or buzz may not occur. This is also applicable to moveme

38、nts of media in the assembly, in single components or parts thereof. Airflow noise in any flap position and blower speed, or due to leak air is not allowed. An audio test (acoustic evaluation) is made during system operation; vibrations from driving operation are simulated by knocking. 4.5 Temperatu

39、re Resistance. Detailed information is indicated in the individual parts of this standard. 4.6 Corrosion Test. 4.6.1 Engine Compartment Components. Single components partly or entirely located in the engine compartment shall fulfill the requirements to GMW3286. 4.6.2 Interior Components. Single inte

40、rior components shall fulfill the requirements to GMW3286. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14780 Copyright 2011 General M

41、otors Company All Rights Reserved December 2011 Page 5 of 5 4.7 High Humidity Environment. Test the complete system to GMW3172. The coding is to be carried out from the individual parts of this standard. In case of missing information, coordination with the release engineer is to be made. 4.8 Vibrat

42、e. Test the complete system to GMW3172. The coding is to be carried out from the individual parts of this standard. In case of missing information, coordination with the release engineer is to be made. 4.8.1 Shock Test. Test to GMW3172. The coding is to be carried out from the individual parts of th

43、is standard. In case of missing information, coordination with the release engineer is to be made. 4.9 Electromagnetic Compatibility. To GMW3091, GMW3097 and GMW3103. 4.10 Flammability. Must comply with FMVSS 302. Test to GMW3232. 4.11 Volatility of Organic Constituents. Test according to GMW3235 -

44、A - 1 mg max. 5 Provisions for Shipping Not applicable. 6 Notes 6.1 Glossary. Fogging: The term used for a condition whereby a thin coating forms on the inside of the windshield and other glass areas and reduces visibility. It is caused by the condensation on the glass surfaces of volatile constitue

45、nts (e.g., plasticizer, stabilizer, oil, greases, blowing agents, release agents, adhesives, etc.) of interior components. 6.2 Acronyms, Abbreviations, and Symbols. CFC Chlorofluorocarbon HVAC Heating Ventilation Air Conditioning 7 Additional Paragraphs 7.1 All parts or systems supplied to this stan

46、dard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: GMW14780 9 Release and Revisions This standard was originated in November 2005. It was first approved b

47、y HVAC Module Global Sub-System Leadership Team in March 2006. It was first published in March 2006. Issue Publication Date Description (Organization) 1 MAR 2006 Initial publication. 2 DEC 2011 Update for 5 Year Refresh. (HVAC Interior Airflow GSSLT) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-