GSA A-A-2846-1994 RAKE HAND (GARDEN AND LAWN)《手耙(草坪和园艺)》.pdf

1、A-A-2646 9999974 OLb5751 7b0 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: General Services Administration, Engineering Group (7FXEE), 819 Taylor St., Fort Worth, TX 76102 - INCH-POUNDI A-A- 2 846 Auau

2、st 1, 1994 COMMERCIAL ITEM DESCRIPTION RAKE, “AND (Garden and Lawn) The General Services Administration has authorized the use of this commercial item description (CID) as a replacement for Federal Specification GGG-R-96 which has been canceled. 1. SCOPE 1.1 ScoDe. This commercial item description c

3、overs garden rakes suitable for raking and smoothing soil, and lawn rakes suitable for raking grass clippings and leaves from lawns. 2. CLASSIFICATION 2.1 Classification. The rakes shall be of the following types, classes, composition, and sizes as specified (see 7.2) : Type I - Garden Rake Class A

4、- Bow distribution is unlimited. FSC 3750 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2846 W 9999974 0165752 bT7 A-A-2846 3.2 e. The type I garden rake shall be designed for raking and smoothing soil. 3.2.1 Class A. Bo w. The head and bow sha

5、ll be forged in one piece from steel. The bow shall be of circular cross-section. The head design shall be similar to figure 1. with using the top of thehead for leveling soil. contain 14 to 16 teeth and be a minimum of 13-1/2 inches (34.3 cm) in width. The head shall have a minimum depth of 2-3/4 i

6、nches (7.0 cm) . The rake handle shall be a minimum of 59 inches (1.49 m) in length. The bow shall not interfere The head shall Figure 1 - Type I, Class A, Bow 3.2.2 Class B, Level head. The head and shank shall be forged in one piece from steel. The teeth shall be as shown in figure 2. The rake sha

7、ll have a single central shank which shall be forced into the handle and reinforced with a ferrule. The shank shall be so arranged as not to interfere with the use of the top of the head for leveling soil. The head shall contain 14 to 16 teeth and be a minimum of 14 inches (35.6 cm) in width. The he

8、ad shall have a minimum depth of 3 inches (7.6 cm) . The rake handle shall be a . minimum of 65 inches (1.65 m) in length. Figure 2 - Type I, Class B, Level Head 3.2.3 Class C, Strikina edse aluminum head. The head shall have a single rib and be formed from extruded aluminum. be as shown in figure 3

9、. slotted to fit over the back rib of the head using one self-locking bolt and nut. Two solid aluminum braces shall encompass the handle and connect to the head with self-locking bolts and nuts. The head shall be available in the following sizes as specified: 24 inch (61 cm), 30 inch (76 cm), 36 inc

10、h (91 cm), 42 inch (107 cm), 48 inch (122 cm) . The head shall be constructed with one rounded tip tooth per each inch of head size. depth of 4 inches (10.2 cm) . The rake shall have a 66 inch (1.68 m) handle with a 5 inch (12.7 cm) vinyl grip. The teeth shall The handle shall be powder coated and T

11、he head shall have a minimum 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-284b m 9999974 0365753 533 m A-A- 2 846 Figure 3 - Type I, Class C, Striking Edge Aluminum Head 3.3 TVR e II, Lawn Rake. Lawn rakes shall be suitable for raking grass

12、clippings, leaves, twigs, and litter from lawns without injury to the grass or roots. The type II, composition S (steel tines) rakes shall have flexible heads consisting of strips of flat spring steel with the bent end forming the head and tines, a handle, and a ferrule or socket suitable for securi

13、ng the head to the handle. consist of a plastic resin body with spring steel tines. Type II, composition P (plastic tines) rakes shall be similar except the entire rake head shall be made from plastic. The plastic shall be a minimum of 95 percent recycled material. The ferrule or socket shall have a

14、 hole suitable for securing the handle by means of a common rivet, screw, or bolt with nut. The handle shall fit tightly within the ferrule or socket. The rake head may 3.3.1 Class A, Radial head, Composition S. The class A, composition S rake shall be similar to figure 4. The tines forming the head

15、 shall be separated at the raking end, grouped together and securely fastened to a steel ferrule at the handle end. The ferrule shall extend over the handle. The head of the rake shall have a steel spreader bar attached to the tines in a fixed position 1 at all times. The spreader bar shall be locat

16、ed between the tips of the tines and the ferrule. The head shall measure a minimum of 17 inches (43.2 cm) in width and have a minimum of 18 tines. The rake handle shall be a minimum of 42 inches (1.06 m) in length. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

17、e from IHS-,-,- A-A-2846 9999974 0365754 47T A-A- 2 84 6 Figure 4 - Type II, Class A, Radial Head 3.3.2 Class A, Radial head, Cornnosition P. The class A, composition P rake shall be similar to figure 4. The tines formi the head shall be separated at the raking end and joined together at the base of

18、 the head. The molded rake head shall include a ferrule which extends over the handle. The head shall measure a minimum of 22 inches (55.9 m) in width and have a minimum of 21 tines. The rake handle shall be a minimum of 46 inches (1.17 m) in length. 3.3.3 Class B, Semiradial head. to figure 5. raki

19、ng end, grouped together and securely fastened to a steel ferrule at the handle end. The ferrule shall extend over the handle. The head of the rake shall have a steel spreader bar attached to the tines to keep them evenly separated and to hold the tines in a fixed position at all times. located betw

20、een the tips of the tines and the ferrule. A backing spring or similar device to provide constant pressure on the head shall be secured to the ferrule, with the spring prongs attached to the spreader bar, to relieve pressure at the stress point on the tines. The rake handle shall be a minimum of 47

21、inches (1.19 m) in length. The class B rake shall be similar The tines forming the head shall be separated at the The spreader bar shall be 3.3.3.1 Size 1,18 inch head width. measure 18 to 20 inches The size 1 rake head shall (45.7 cm to 50.8 cm) in width and have 18 to 22 tines. 3.3.3.2 Size 2, 22

22、inch head width. measure 22 to 26 inches (55.9 cm to 66.0 cm) in width and have 21 The size 2 rake head shall to 26 tines. I Figure 5 - Type II, Class B, Semiradial Head 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2846 9999974 0365755 306 A

23、-A- 284 6 3.3.4 Double-Rib aluminum head. The head shall have a double-rib and be formed from extruded aluminum. The teeth shall be as shown in figure 6. The handle shall be powder coated and made to fit in between the double-rib of the head using one self-locking bolt and nut. Two solid aluminum br

24、aces shall encompass the handle and connect to the head with self-locking bolts and nuts. The head (61 cm), 30 inch (76 cm), 36 inch (91 cm), 42 inch (107 cm), 48 inch (122 cm). The head shall be constructed with one rounded tip tooth per each inch of head size. depth of 4 inches (10.2 cm) . The rak

25、e shall have a 66 inch (1.68 m) handle with a 5 inch (12.7 cm) vinyl grip. - $ shall be available in the following sizes as specified: 24 inch The head shall have a minimum Figure 6 - Type II, Class C, Double-Rib Aluminum Head 3.4 Finish. All metal surfaces shall have a painted, plated, lacquered, o

26、r enameled finish. Metal handles shall be plated, anodized, or have a painted finish. Wood handgrips shall be smooth and shall have an applied coating of varnish, lacquer, or polyurethane. 3.5 Identification markinq. The rakes shall be marked with the manufacturers name or trademark. The use of an a

27、dhesive-backed label shall be acceptable. 3.6 WorkmanshiD. The rakes shall be free from ragged edges, cracks, holes, pits, and other defects which would affect the appearance and serviceability of the item. 3.7 Metric Droducts. Products manufactured to metric dimensions will be considered on an equa

28、l basis with those manufactured using 1 inch-pound units, providing they fall within tolerances specified and all other requirements of this document are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request sho

29、uld be made to the contracting officer to determine if the product is acceptable. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A- 2846 3.9 $tandard commercial Droduct. The rakes shail, as a minimum, be in accordance with the requirements of th

30、is CID and shall be the manufacturers standard commercial product. product is a product which has been sold or is currently offered for sale on the commercial market through advertisements, manufacturers catalogs, or brochures, and represents the latest production model. A standard commercial - Type

31、 (1 - I, 2 - II, 3 - III) Class (A, B, or C) Composition (P or S) I - - 4. REGULATORY REQUIREMENTS Size (i or 2) - 4.1 Recovered materials. The of ferer/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisiti

32、on Regulation (FAR). -_- Commercial Item Description number 5. QUALITY ASSURANCE PROVISIONS 5.1 Contractor certification. The contractor shall certify and maintain substantiating eviqence that the product offered meets the salient characteristics of this Commercial Item Description, and that the pro

33、duct conforms to the producers own drawings, specifications, standards, and quality assurance practices, and is the same product offered for sale in the commercial marketplace, or is the same product that has been successfully delivered to the government on a previous contract or purchase order. gov

34、ernment reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The 6. PACKAGING 6.1 Preservation, Dackinq. and markinq. The preservation, packing, and marking shall be as specified in t

35、he contract or order. 7. NOTES 7.1 Part identification numberinu system. Items conforming with this Commercial Item Description shall be identified by a part identification number configuration consisting of identification of a portion of the Commercial Item Description number, type, class, composit

36、ion, and size. number configuration is shown below. numbering system is intended for identification and cross-indexing of the item within the Federal cataloging system. identification numbers are not required to be placed on the product or container. An example of the part identification This part i

37、dentification Part I 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2846 9977774 0365757 389 W A-A-2846 7.2 Orderincr data. Purchasers should select the preferred options permitted herein and include the following information in procurement do

38、cuments (if applicable). a. Title, number, and date of this commercial item b. Type, class, compbsition, and size required. c. The preservation, packing, and marking required. description. 7.3 Fisures. The figures shown herein are descriptive and not restrictive, and not intended to preclude the pur

39、chase of rakes which are otherwise in accordance with the requirements of this commercial item description. 7.4 National Stock Numbers (NSNs): The following is a list of NSNs assigned which correspond to this commercial item description. This list may not be indicative of all possible NSN s. NSN 375

40、0-00-171-7182 3750-00-243-2408 3750-00-599-6101 3750-01-372-4150 3750-00-086-7690 3750-00-903-0720 MILITARY INTERESTS: Custodians Air Force - 99 Type Class Comp. Size Nomenclature I A - - Rake, Garden I B - Rake, Garden Rake, Lawn II A S II A P - Rake, Lawn II B - 1 Rake, Lawn II B - 2 Rake, Lawn - PREPARING ACTIVITY: GSA - 7FXEE Review Activities Air Force - 84 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-