NAVISTAR MPAPS S-M-4 101-GS PL-2015 Pipe Nipples C English Series (Noun Code 5760).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 3 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-M-4.101-GS/PL Former Designation: ESP-M-4.101-GS TITLE: Pipe Nipples English Series (Noun Code 5760) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-M-4.101-GS - August 2006 PRINTED COPIES OF THI

3、S DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices

4、and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, PP, NPP. Dimensions in inches: A B C Effective Thread Length Close Nipples Length (L) Taper Pipe Thread Outside Diameter Inside Diameter Wrought Steel Brass 1/8 .405 .269 .2

5、81 .264 3/4 1/4 .540 .364 .375 .402 7/8 3/8 .675 .493 .494 .408 1 1/2 .840 .622 .625 .534 1-1/8 3/4 1.050 .824 .822 .546 1-3/8 1 1.315 1.049 1.062 .683 1-1/2 1-1/4 1.660 1.380 1.368 .707 1-5/8 1-1/2 1.900 1.610 1.600 .724 1-3/4 2 2.375 2.067 2.062 .756 2 1.0 MATERIAL: Wrought Steel Pipe - CEMS A-18,

6、 Grade 1. Stainless Steel, SST-201 per MPAPS A-37. Brass (BRS) - Grades C12200, C23000, C26000 per CEMS C-3. NUMBER: MPAPS S-M-4.101-GS/PL TITLE: Pipe Nipples REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technic

7、al Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 3 2.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability and cost savings in volume

8、buying. For new design, parts shall be selected from “Approved“ part list only. Material: Wrought Steel (STL) Finish: Plain (PLN) Length Incrementation: Close Nipples - See (L) Table Above Long Nipple - 1-1/2 inches thru 6 inches = 1/2 inch increments - 6 inches thru 12 inches = 1 inch increments 3.

9、0 THREADS: American National Standard Taper Pipe Thread ANSI B2.1. The gaging limit will be plus or minus one thread. Threads will be chamfered to a 45 angle, one thread deep. All brass nipples shown in section 8.0 must be made with Dryseal American Standard Taper Pipe Thread (NPTF) per SAE J476. Se

10、alant Coating: All fittings that have external pipe threads will be furnished with a pre-applied sealant coating on the pipe threads that meets the requirements of CEMS D-31. 4.0 FINISHES: As designated by part number, pipe nipples will be furnished plain, plated or coated in accordance with MPAPS a

11、nd class listed below: Zinc Trivalent, Class 6A (ZN6A) MPAPS G-20, Class 6A Phosphate Coating (PHC) MPAPS G-1, Class B-2 Galvanized (GAL) Pipe - will be coated with zinc inside and outside by the hot dip process. Zinc used for the coating will be any grade of zinc conforming to specification for sla

12、b zinc (ASTM B-6). Weight of zinc coating will not be less than 2.0 ounces per square foot of total coated surface. Short (close) nipples are not galvanized. Nipples are threaded after galvanizing or plating. Galvanized parts must be brushed after threading to remove excess coating. 5.0 RESTRICTED C

13、HEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 6.0 WORKMANSHIP: Pipe nipples must be free from burrs, loose scale, sharp edges and all other defects that might affect the

14、ir serviceability. 7.0 PART LIST: 7.1 Approved: Taper Length Type Finish Material Part Thread Number 1/8 2 1/2 LONG PLN STL 120549 3/8 1 CLOSE PLN STL 121207 3/8 1 1/2 LONG PLN STL 109421 1/2 1 1/2 LONG PLN STL 141504 3/4 4 1/2 LONG PLN STL 127850 1/8 .750 CLOSE PLN BRS 142868 1/4 2 LONG PLN BRS 144

15、597 1/2 2 LONG ZND STL 192076 1/2 2 1/2 LONG PLN BRS 189611 1/2 2 1/2 LONG PLN STL 121664 NUMBER: MPAPS S-M-4.101-GS/PL TITLE: Pipe Nipples REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppl

16、iers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 3 8.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/