NAVISTAR TMS 6914-2009 Sealer Tape Door.pdf

1、This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 1 of 4 NAVISTAR INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS-

2、6914 TITLE: Sealer Tape, Door CURRENT REV No.: 0912 DATE: December 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev. B-1, August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materia

3、ls, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Replaced “In

4、ternational Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; editorial changes. Reference: File 30-1 Keywords: Tape; Sealer 1.0 APPLICATION This specification covers a smooth, black crepe paper tape recommended and designed for sealing access

5、holes in truck door panels. 2.0 SCOPE This specification covers the general requirements, property and performance requirements, quality, packaging, storage and identification, source approval and quality control. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to

6、the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in this specif

7、ication. Quality System Standard ISO 9001 or TS-16949 NAVISTAR TMS-7084 CFR Title 29, Section 1910 ASTM B 117 NAVISTAR Manufacturing Std. MS-D-13 ASTM D 193 NAVISTAR Eng. Design Std. A-16 ASTM D 1000 NAVISTAR CEMS B-50 ASTM D 1938 NAVISTAR TMS-9543 4.0 GENERAL REQUIREMENTS 4.1 Material The crepe pap

8、er tape shall be a tough, general purpose, heat resistant type treated with a saturant and a pressure sensitive synthetic rubber resin adhesive. The tape shall have the capability of withstanding oven temperatures of 138C (280F) for one hour. The tape shall have long aging qualities and be water res

9、istant. The adhesive shall be formulated for high tack characteristics. 4.2 Thickness 0.17 mm (0.0065 in) minimum. NUMBER: TMS-6914 TITLE: Sealer Tape, Door REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical

10、Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 2 of 4 4.3 Property and Performance Requirements 4.3.1 Tensile Strength and Elongation 4.3.1.1 Method ASTM D 1000 - The stressing jaw speed shall be constant and at the rate of 300 13 mm (12 1/2 i

11、n) per minute. Specimen shall be 25 mm (1 in) in width. 4.3.1.2 Required Tensile Strength: 14.5 MPa (2 100 psi) minimum. Elongation: 9% minimum. 4.3.2 Tear Strength 4.3.2.1 Method ASTM D 1938 4.3.2.2 Required 0.88 N/cm (8 ozf/in) width minimum 4.3.3 Peel Strength 4.3.3.1 Method ASTM D 1000 - Apply t

12、ape to panels: 1) steel-plain, 2) steel-painted, 3) aluminum-plain, 4) aluminum-painted. Allow to age for one hour before performing test. 4.3.3.2 Required Tape shall meet 4.38 N/cm (2.5 lbf/in) width minimum peel strength to plain or painted surface on each type of panel. 4.3.4 Heat Aging 4.3.4.1 M

13、ethod Mount tape on steel or aluminum panel with painted and unpainted surfaces and age for one hour at 138C (280F), then return to room temperature before inspection. Inspect visually. 4.3.4.2 Required No loss of adhesion, embrittlement or loss of water resistant qualities. 4.3.5 Resistance to Corr

14、osive Atmosphere 4.3.5.1 Method Two steel panels 30 cm x 30 cm x 1.6 mm (12 x 12 x 1/16 in) with 1.3 cm (1/2 in) diameter holes drilled 10 cm (4 in) apart over the entire panel. Apply tape completely covering the panel and holes overlapping the tape 3 mm (1/8 in). Perform corrosion testing as specif

15、ied per ASTM B 117 for a total of 96 hours. 4.3.5.2 Required No visible permeation of the corrosive atmosphere shall be exhibited when the tape is removed from the surface it was protecting, indicating the tape is water resistant and not corrosive to the metal surface it contacts. Also, there shall

16、be no visible loss of adhesion of the tape from the metal panel or around the perimeter of the drilled access holes. 4.3.6 Chemical Resistance 4.3.6.1 Method Apply tape to steel and aluminum panels and immerse individual panels in window wash solvent, car washing detergent and SAE Multi-Grade oil fo

17、r two hours. 4.3.6.2 Required No visible loss of adhesion, bubbling, shrinking, or disintegration of the mounted specimen. NUMBER: TMS-6914 TITLE: Sealer Tape, Door REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Te

18、chnical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 3 of 4 4.3.7 Cold Resistance 4.3.7.1 Method TMS-7084 (Cold Impact Resistance) - Part to be mounted to exterior surface of slam panel without the use of the slam bar; test according to Figu

19、re 1. 4.3.7.2 Required There shall be no visible loss of adhesion when impact tests are executed. 4.4 Application The tape shall have the ability to be used effectively over a relatively clean surface wiped with a clean shop towel. The adhesive shall have the required flexibility and be aggressive e

20、nough to be applied at 20C (66F) with full adhesion. 4.4.1 The tape shall meet the production installation requirements for a satisfactory application before final approval is granted. 5.0 QUALIFICATION Material and processes submitted for approval to this specification shall include the following:

21、5.1 A detailed, signed test report documenting testing to this specification per TMS-9543. 5.2 Test coupons or photographs showing failure modes for each test. 5.3 The complete procedure used for preparing and curing materials for test, especially surface preparation and condition of the test specim

22、ens. 5.4 Questions regarding qualification requirements, reports and test materials may be directed to: Manager of Non-Metallic Materials Materials Engineering and Technology Truck Development and Technology Center PO Box 1109 Fort Wayne, IN 46801 6.0 QUALITY The crepe tape supplied under this speci

23、fication shall be uniform in color and density, free from pin holes and foreign matter. 7.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to Navistar Inc. are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registrat

24、ion as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon

25、request. 7.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes i

26、n material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, Truck Development and Technology Center and Navistar Purchasing NUMBER: TMS-6914 TITLE: Sealer Tape, Door REVISION: 0912 This document is restr

27、icted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 4 of 4 and Supplier Development of the proposed change(s). Test data indicating conformanc

28、e to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 7.3 Process Control The supplier shall either perform and/or report results of tes

29、ts on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the qual

30、ity control manager of the using Navistar plant may determine testing and reporting requirements on specific products. 8.0 SHIPPING, PACKING AND IDENTIFICATION Loading, packing, and identification shall be in accordance with Manufacturing Std. MS-D-13. 8.1 Packaging The tape shall be 5 cm (2 in) wid

31、e and wrapped around a cardboard core having an inside diameter of 7.5 cm (3 in) or 17.5 cm (7 in), unless otherwise specified by the using manufacturing plant. The core shall be of sufficient rigidity to prevent collapse of the roll under the winding tension necessary to produce a tight wrap and fo

32、r ease in handling during production application. The tape shall be so rolled that the edges are not folded over, and the length shall be continuous. The tape roll shall be suitably identified on the cardboard core to indicate the tape width, product description, date of manufacture, and manufacture

33、r. 8.2 Storage The tape shall meet requirements after being stored for periods up to one year. 9.0 DESIGNATION ON DRAWINGS Sealing Tape per TMS-6914. 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled

34、copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ 11.0 APPROVED SOURCE Armak Industrial Products Division: PB-I Minnesota Mining and Manufacturing Company (3M): Scotch Brand No. 217