NAVISTAR TMS 7029-2011 Coiled Nylon Air Brake Tubing.pdf

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2011 by Navistar, Inc. AUGUST 2011 Page 1 of 5 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER:

2、 TMS-7029 TITLE: Coiled Nylon Air Brake Tubing CURRENT REV. No.: 1108 DATE: August 2011 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev 0904 - April 2009 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve h

3、azardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Noti

4、ce: Removed redundant specification references; editorial changes. . Reference: File 20-3 Keywords: Air Brake Tubing; Nylon; Coiled 1.0 APPLICATION This specification outlines the minimum requirements for a coiled nylon tubing assembly that may be used in the air brake system. The use of this produc

5、t is restricted by SAE J844 and must have approval of Truck Development and Technology Center Brake Group. 2.0 SCOPE This specification covers the general requirements, property and performance requirements, and the quality control requirements. An approved source list is included. 2.1 Restricted Ch

6、emical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The following spe

7、cifications and standards are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 CFR Title 29, Part 1910 TMS-9528 NAVISTAR Eng. Design Std. A-16 ASTM D 622 TMS-9543 NAVISTAR CEMS G-18 ASTM A 318 SAE J844 NAVISTAR CEMS G-20 ASTM D 2122 CEMS B-50 NAVISTAR TMS-7006 NAVISTAR

8、TMS-9009 4.0 GENERAL REQUIREMENTS The tubing and completed assembly shall meet the provisions outlined in the various requirements of this specification and the requirements of the latest issue of TMS-7006. 4.1 Material The assemblies shall be constructed of reinforced tubing meeting the requirement

9、s of TMS-7006. 4.2 Appearance The tubing assembly shall conform to and be equivalent in surface finish and color to that of the pre-production samples approved by TDTC. Assemblies supplied to this specification shall be smooth and uniform, free from any visible defects, foreign matter, kinks, seams

10、or any other conditions that would impair the performance. NUMBER: TMS-7029 TITLE: Coiled Nylon Air Brake Tubing REVISION: 1108 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume

11、 all patent liability. 2011 by Navistar, Inc. AUGUST 2011 Page 2 of 5 4.3 Color The tubing formulation shall be consistent in hue and of uniform saturation so that it matches the appearance of pre-production approved samples and meets the applicable color requirements of the aforementioned standards

12、. Approved color shall be designated on the assembly drawing. 4.4 Fittings Fittings shall be made from brass and spring guards of steel, meeting the dimensional requirements shown on the engineering drawing. Steel shall be plated with zinc plating, Class 8A, CEMS G-20 or painted per TMS 9009, Class

13、IIA. Spring guard free end shall be rounded and relieved to prevent abrasion of nylon tubing. 4.5 Property And Performance Requirements All assemblies furnished to this specification shall meet the provisions and requirements of TMS-7006, and, in addition, the following requirements: 4.5.1 Sag Resis

14、tance 4.5.1.1 Method Extend coiled assembly to the maximum recommended working length (as specified on the part drawing) in a horizontal position by clamping at ends and hold for 16 hours at 24 3C (75 5F). While in the extended position, measure the deflection from a horizontal line at top of the co

15、il at the assembly mid-point. Reduce the extension of the assembly to 50% of the recommended working length and hold. After 30 minutes, repeat the sag measurement. 4.5.1.2 Required Sag from the horizontal shall not exceed 4% of the maximum working length for full extension nor more than 8% of maximu

16、m working length for 50% extension. 4.5.2 Force of Extension 4.5.2.1 Method Extend coiled assembly to the maximum recommended working length at 24 3C (75 5F). Using a spring scale or other suitable measurement device, determine total force of extension. 4.5.2.2 Required Force to extend to maximum wo

17、rking length shall not exceed 66.7 N (15 lbf). 4.5.3 Ovality - Nylon Tubing 4.5.3.1 Method: ASTM D 2122, Section #7, Calculations M in im um O .D.M a xi m um O .D. x 10 0 4.5.3.2 Required: Shall be a minimum of 75% ovality. 4.5.4 Restriction 4.5.4.1 Method: Measure the inside diameter of the metalli

18、c sleeve (sleeve inside tubing). 4.5.4.2 Required: A 12.7 mm (1/2 in) O.D. coiled assembly shall have a minimum sleeve I.D. of 8.0 mm (0.315 in). 4.5.5 Fitting Tensile 4.5.5.1 Method: ASTM D 622 4.5.5.2 Required: Minimum pull-off shall be 1.45 kN (325 lbf) 4.5.6 Spring Guard Tensile 4.5.6.1 Method:

19、ASTM A 318, Section 3, with cross head speed of 2.5 cm (1 in) per minute. NUMBER: TMS-7029 TITLE: Coiled Nylon Air Brake Tubing REVISION: 1108 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are req

20、uired to assume all patent liability. 2011 by Navistar, Inc. AUGUST 2011 Page 3 of 5 4.5.6.2 Required Minimum force to remove spring from fitting shall be 445 N (100 lbf). 4.5.7 Quality Control Requirements The supplier shall perform the following control tests on production parts and on a continuin

21、g basis according to the test frequency stipulated: 4.5.7.1 Leak Test Two assemblies per lot shall show no leakage when tested for five minutes under 1.4 MPa (200 psi) air pressure. Leakage of sample part shall require 100% leak testing of the subject lot. Note: A lot is defined as the product of on

22、e size and/or color assemblies made during one day of production. 5.0 QUALITY Parts and assemblies will meet the cleanliness requirements of TMS-9528. All product produced to this specification will be clean, free of dirt, grease, and contamination. All debris from cutting and processing will be rem

23、oved. Any internal release agents shall be flushed from the inside of the tubing. There shall be no fabric or flash exposed on the ID of the hose. Parts shall be free of voids and/or reinforcement splices. 5.1 KCC Key Control Characteristics Refer to Engineering Design Standard A-16. Unless specific

24、 exception is noted on the engineering drawing or purchase order, the following features/characteristics are identified as features for which management by statistical process control is mandatory for all tube and/or tube assemblies supplied to the requirements of this specification. Ovality Restric

25、tion Length 5.2 Certification Assemblies supplied to this specification shall be certified and records maintained to compliance with SAE J844 and TMS-7006. These records shall be subject to periodic review by International Quality Personnel 5.3 Qualification Material and processes submitted for appr

26、oval to this specification shall include the following: 5.3.1 Report: A detailed and signed test report documenting testing to this specification prepared as per TMS-9543. The report will include actual test data not merely test summaries. 5.3.2 Failure Modes: Test samples or photographs showing fai

27、lure modes for each destructive test as necessary to fully describe those failure modes. Descriptions are adequate if the mode is easily understandable (no jargon) and not unexpected. Unexpected failure modes shall be described or pictured as completely as possible. 5.3.3 Test Procedure: The procedu

28、re used for preparing, curing and assembling materials for test. 5.3.4 Analysis: A detailed analysis of the test results including assumptions made, unexpected results and an explanation of any non-compliant results. NUMBER: TMS-7029 TITLE: Coiled Nylon Air Brake Tubing REVISION: 1108 This document

29、is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2011 by Navistar, Inc. AUGUST 2011 Page 4 of 5 5.4 Submission The material test report shall be submitted to: Manager o

30、f Non-Metallic Materials Materials Engineering and Technology Navistar, Inc. PO Box 1109 Fort Wayne, IN 46801 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements All suppliers to Navistar Inc. are required to be registered to ISO 9001 Quality System Requirements. Navistar will also acc

31、ept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Navistar

32、 Corporate Buyer upon request. 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In th

33、e event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering at TDTC and Purchasing and Logistics of the proposed change(s). Test data indicating conformance to all requirements of th

34、is specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts p

35、roduced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the usi

36、ng Navistar plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION The tubing and fittings furnished to this specification shall comply with the identification requirements of SAE J844 and TMS-7006. 8.0 DESIGNATION ON DRAWINGS TMS-7029 9

37、.0 APPROVED SOURCES Eaton Parker Hannifin NUMBER: TMS-7029 TITLE: Coiled Nylon Air Brake Tubing REVISION: 1108 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liabi

38、lity. 2011 by Navistar, Inc. AUGUST 2011 Page 5 of 5 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/