ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:22.52KB ,
资源ID:963633      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-963633.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(NAVISTAR TMS 7072-2001 Foundation Board Door Trim (Revision F-1).pdf)为本站会员(explodesoak291)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

NAVISTAR TMS 7072-2001 Foundation Board Door Trim (Revision F-1).pdf

1、 This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. Ge32001 by International Truck and Engine Corporation. AUGUST 2001 Page 1 of

2、 3 INTERNATIONAL TRUCK AND ENGINE CORPORATION TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS-7072 TITLE: Foundation Board, Door Trim REVISION: F-1 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering DATE ISSUED: August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR

3、 CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicabil

4、ity of regulatory limits prior to use. Change Notice: Reformatted and Editorial Changes Reference: File 30-6A Keywords: Door Trim; Foundation Board 1.0 APPLICATION This specification covers a semi-rigid fiberboard, silk screen coated for dielectric bonding, suitable as a structural foundation board

5、or supporting member for soft trim applications. 2.0 SCOPE This specification covers the general requirements, property and performance requirements and quality. 3.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The following Specifications,

6、 Standards, and Regulations are referenced in this specification. Quality System Standard QS-9000 (ISO 9001) INTERNATIONAL Manufacturing Standard D13 INTERNATIONAL ISR Quality Standard CFR 29, Part 1910 INTERNATIONAL TMS-9544 CFR 49, Part 571.302 4.0 GENERAL REQUIREMENTS 4.1 Construction This board

7、shall be constructed from kraft and other fibers suitable to meet the requirements of the intended use, laminated on both sides with 0.03 mm (0.001 in) film of polyethylene and a kraft paper liner. The outer face shall be silk screen coated with a dielectrically active plastic (PVDC or equivalent) f

8、ilm. 4.2 Finished Thickness Standard thicknesses shall be 1.0, 1.5 and 2.0 mm (0.040, 0.060, and 0.080 in); tolerance on all thicknesses shall be 0.13 mm (0.005 in). NUMBER: TMS-7072 TITLE: Foundation Board, Door Trim REVISION: F-1 This document is restricted and may not be sent outside Internationa

9、l Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. Ge32001 by International Truck and Engine Corporation. AUGUST 2001 Page 2 of 3 4.3 Property And Performance Requirements Unless otherwise indicat

10、ed, material testing shall be in accordance with SAE J315 - Fiberboard Test Procedure. 4.3.1 Moisture Content 4.5-7.0% 4.3.2 Bursting Strength: Mullen Burst 4.3.2.1 Method Perform test dry and after 24 hour immersion in water. 4.3.2.2 Required Dry: 22.2 N (5 lbf) per mil thickness minimum Wet: 17.8

11、N (4 lbf) per mil thickness minimum 4.3.3 Water Absorption: 15 x 15 cm (6 x 6 in) Sample 24 hours: 12% maximum 4.3.4. Dimensional Stability: Method B and Method C at 70 C (158 F) 4.3.4.1 Expansion Machine Direction: 0.7% maximum Across Machine Direction: 0.7% maximum 4.3.4.2 Contraction Machine Dire

12、ction: 0.7% maximum Across Machine Direction: 0.7% maximum 4.3.5 Flammability Resistance Material and parts supplied to this specification shall conform to and be certified by the suppliers to meet the requirements of (CFR 49, Part 517.302) Federal Motor Vehicle Safety Standard #302 - Flammability o

13、f Interior Materials and TMS-9544. 5.0 QUALITY The material shall be free from objectionable odor, have necessary flexibility to meet contour requirements, be adequately bonded to prevent separation and be uniform in thickness. 5.1 Primary cosmetic vinyl surfaces shall be free from voids, bumps, dim

14、ples, cuts, wrinkles, and bubbles. Surfaces that are not normally visible shall be indicated on the print and shall meet a mutually agreed level of surface quality and be so stated in the part control plan. The exposed foam surface shall be free of voids or imperfections detrimental to strength, fit

15、, function, or service life. NUMBER: TMS-7072 TITLE: Foundation Board, Door Trim REVISION: F-1 This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all

16、patent liability. Ge32001 by International Truck and Engine Corporation. AUGUST 2001 Page 3 of 3 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements Suppliers must conform to the requirements of the International IQR Quality Standard which includes conformance to the QS-9000 (ISO 9001)

17、 Quality System Standard. A mutually acceptable Quality Control Plan as described therein is required for source approval to the requirements of this specification. 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those

18、 samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials

19、Engineering at TDTC and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be sub

20、mitted with the request for change. 6.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts produced or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all requi

21、red properties. The part supplier and the plant metallurgist and/or the quality control manager of the using International plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION Loading, packing, and identification shall be in accordance with Manufacturing Std. D-13. 8.0 DESIGNATION ON DRAWINGS Unless otherwise specified, the standard thickness shall be 2.0 mm (0.080 in). Examples: Foundation Board per TMS-7072 or Foundation Board per TMS-7072, Thickness 1.0 mm (0.040 in)

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1