NAVY MIL-B-29605-1994 BODY ARMOR SOFT SMALL ARMS PROTECTIVE PRU-60 P22P-15《PRU-60 P22P-15小型武器防护软防弹衣》.pdf

1、MIL-B-29b05 = 99999Ob 1995788 138 INCH - POUND I I MIL-B-29605 (AS) 15 December 1994 MILITARY SPECIFICATION BODY ARMOR, SOFT, SMALL ARMS PROTECTIVE, PRU-60/P22P-15 This specification is approved for use by the Department of the Navy, and is available for use by all Departments and Agencies of the De

2、partment of Defense. 1. SCOPE 1.1 Scope. This specification covers the general requirements and inspections for soft body armor used by helicopter aircrewmen for protection against small arms projectiles. 1.2 Classification. The soft body armor assemblies furnished under this specification will be o

3、ne of the following sizes (see 6.2d): Sma 11 Medium Large X-Large 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of th

4、ese documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2e). Beneficial comments (recommendations, additions, deletions, and any pertinent data which may be of use in improving th

5、is documept should be addressed to: Commander, Systems Standardization, Code 4.1.11B120-3, Naval Air Warfare Center Aircraft Division, Highway 547, Lakehurst, NJ 08733-5100, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document

6、 or by letter. AMSC-N/A FSC 8470 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-B-29b05 999990b 1995789 074 M MIL-B-29605(AS) . SPECIFICATIONS FEDERAL UU-P-268 PP

7、P-B-636 MILITARY MIL-W-4088 MIL-W-5664 MIL-F-21840 MIL-C-43734 MIL-C-43842 MIL-C-44050 STANDARDS MILITARY MIL-STD-105 MIL-STD-129 MS27980 Paper, Kraft, Wrapping. Boxes, Shipping, Fiberboard. Webbing, Textile, Woven Nylon Webbing, Textile, Elastic (Validated) Fastener Tapes, Hook and Pile, Synthetic

8、Cloth, Duck, Textured Nylon Cloth, Oxford, Aramid Cloth, Ballistic, Aramid Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage Fastener, Snap, Style 2 (Regular Wire Spring Clamp Type) (Unless otherwise indicated, copies of federal and military specifications,

9、 standards, and handbooks are available from DODSSP, Standardization Document Order Desk, 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA 1911-5094.) 2.1.2 Government drawinss. The following Government drawings form a part of this document to the extent specified herein. Unless otherwise specified, t

10、he issues are those cited in the solicitation. DRAWINGS 324 1AS201 324 1AS2 02 3 24 1AS2 03 3 2 4 1AS2 04 3 2 4 1AS2 O5 324 1AS280 3 24 1AS28 1 3 24 1AS2 82 - Soft Body Armor System Assembly, - Soft Ballistic Insert Assembly, - Casing Assemblies, PRU-60/P22P-15 - H-Harness Assembly, PRU-60/P22P-15 -

11、 Label, Identification, - Ballistic Patterns, Small, - Ballistic Patterns, Medium, - Ballistic Patterns, Large, PRU-60/P22P-15 PRU-60/P22P-15 PRU-60/P22P-15 PRU-60/P22P-15 PRU-6O/P22P-15 PRU-60/P22P-15 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

12、-,-MIL-B-29605 999990b L995790 89b m MIL-B-29605 (AS) DRAWINGS (contd) 3 24 1AS283 3 2 4 AS2 84 3 2 4 AS2 8 5 3 24 1AS2 8 6 3 24 1AS2 87 3 24 1AS2 88 324 1AS2 89 324 1AS2 90 3 24 1AS2 9 1 Ballistic Patterns, Extra Large, Cover Patterns, Front, Back, Side, Small, PRU-60/P22P-15 Cover Patterns, Front,

13、 Back, Side, Medium, PRU-O/P22P-15 Cover Patterns, Front, Back, Side, Large, PRU-60/P22P-15 Cover Patterns, Front, Back, Side, Extra Large, PRU-60/P22P-15 Casing Pattern, Small, Casing Pattern, Medium, Casing Pattern, Large, Casing Pattern, Extra Large, PRU-60/P22P-15 PRU-60/P22P-15 PRU-60/P22P-15 P

14、RU-60/P22P-15 PRU-60/P22P-15 (Unless otherwise specified, copies of drawings required by contractors in connection with specific acquisition functions should be obtained from the contracting activity, or as directed by the Contracting Officer.) 2.2 Non-Government publications. The following document

15、s form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified issues of documents not listed in the DODISS are the issues o

16、f documents cited in the solicitation (see 6.2e) . AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D3951 - Packaging, Commercial (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) NATIONAL INSTITUTE OF JUSTICE N

17、IJ Standard 0101.03 - Ballistic Resistance of Police Body Armor (Application for copies should be addressed to Chief, Law Enforcement Standards Laboratory, National Bureau of Standards, Gaithersburg, MD 20899.) 2.3 Order of precedence. In the event of a conflict between the text of this specificatio

18、n and the references cited herein, the text of this specification shall take precedence. Nothing in this 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-B-29bO5 D 999990b 3995793 722 D MIL-B-29605 (AS) specification, however, shall supersede ap

19、plicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Qualification. The soft body armor furnished under this specification shall be produ 3 which are authorized by the qualifying activity for list .g on the applicable qualified products list at the time of

20、 award of contract (see 4.3 and 6.4). Qualification of any one size assembly, under this specification, will automatically qualify a supplier for all sizes specified herein (see 1.2). 3.2 First article. When specified (see 6.2f), a sample shall be subjected to the first article inspection (see 6.5)

21、in accordance with 4.4. 3.3 Materials and components. The materials and components shall conform to applicable specifications, standards, and drawings and shall be as specified herein. Equivalent materials and parts require approval by the Naval Air Warfare Center Aircraft Division Warminster (Code

22、603), Warminster, Pennsylvania 18974-5000. Requests for use of equivalent items shall be submitted to the Contracting Officer. 3.3.1 Ballistic inserts. The ballistic inserts shall be fabricated from ballistic aramid cloth conforming to MIL-C-44050, Type I and Type II (see 3.4.1.2). 3.3.2 Ballistic i

23、nsert covers. The ballistic insert covers shall be fabricated from texture nylon duck cloth conforming to MIL-C-43734, Class 3, Color 106 Olive Green (See 3.4.1.2). 3.3.3 Casins Assemblies. The casing assemblies shall be fabricated from oxford aramid cloth conforming to MIL-C-43842, Class I, Color 1

24、06 Olive Green (see 3.4.1.2). 3.3.4 Webbinqs. 3.3.4.1 Back casinq assembly The side straps for the back casing assembly shall be fabricated from elastic webbing conforming to MIL-W-5664, Type I, Class 1, 2 inch wide. The shoulder straps for the back casing assembly shall be fabricated from nylon web

25、bing conforming to MIL-W-4088, Type XII, Class 2, 1 23/32 inch wide. 3.3.4.2 H-Harness assembly. The side straps for the H- Harness assembly shall be fabricated from nylon webbing conforming to MIL-W-4088, Type VIII, Class I, 1 23/32 inch wide. The shoulder straps for the H-Harness assembly shall be

26、 fabricated from nylon webbing conforming to MIL-W-4088, Type VII, Class I, 1 23/32 inch wide. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-B-29605 m 0b I1995792 bb m 3.3.5 Hook and pile tapes. 3.3.5.1 Hook tape. The hook tape shall be nylon i

27、n accordance with MIL-F-21840, Type II, Class I, 1 and 2 inch wide as specified in 3.4. 3.3.5.2 Pile tape. The pile tape shall be nylon in accordance with MIL-F-21840, Type II, Class I, 1, 2 and 4 inch wide as specified in 3.4. 3.3.6 Snap fasteners. 3.3.6.1 Front and back casinq assemblies. The fron

28、t and back casing assemblies eyelet and stud snap fasteners shall be in accordance with MS27980-8B and MS27980-7B, respectively. 3.3.6.2 Side casinq assembly. The side casing assembly socket and button snap fasteners shall be in accordance with MS27980-6B and MS27980-1B, respectively. 3.4 Desian and

29、 construction. Unless otherwise specified, the design and construction of the soft body armor assembly shall conform to the drawings listed in paragraph 2.1.2 of this specification. 3.4.1a Cut edses. The cut edges of the nylon webbings and tapes, except for the hook and pile fastener tapes, shall be

30、 seared, prior to the fabrication of the soft body armor, to prevent fraying. No sharp edges shall be formed. The cut edges of the nylon duck cloth, except those that are completely covered by nylon binding tape, hook and pile fastener tapes, or are completely encased by the seam construction, shall

31、 be overedged stitched (serged) . 3.4.1.1 Patterns. Standard patterns will be furnished by the Government to the contractor for use in cutting working patterns (see 6.6). The working patterns shall be identical to the Government patterns. Neither the Government patterns nor the working patterns shal

32、l be altered in any way. Seams shall be in accordance with seam allowances specified in 3.4. 3.4.1.2 Component parts. The component parts shall be cut from the material specified, in accordance with the pattern parts in Table I. 3.4.2 Seams and stitchinq. All the seams used in the fabrication of the

33、 soft body armor shall conform to the applicable drawings. Except for the serging (overedge), the stitching shall be accomplished with Stitch Type 301. The overedge stitching shall be accomplished with Stitch Type 502, 503, 504, or 505. The width of the overedge stitching shall be approximately 1/4

34、inch. The thread and stitching used in fabrication shall conform to applicable drawing requirements. All the seam edges shall be properly forced out and shall not contain any folds. No seams 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-29b

35、05 9999906 I1995793 5T5 MIL-B-29605(AS) shall be twisted, puckered, or pleated and no part of the soft body armor assemblies shall be caught in an unrelated operation or seam. All the thread ends shall be trimmed to a length of 1/4 to 3/8 inch and except for the webbing, cord, and tape, excluding th

36、e binding tape, no raw or cut edge shall be visible on the exterior of the soft body armor assemblies. The cut edges of the binding tape shall be turned under. 3.4.2.1 Sewinq. Each row of stitching shall be straight and parallel to the seam edge. The straightness of the stitching, in any row, shall

37、be maintained within a tolerance of plus or minus 1/32 inch. The ends of the stitching that are not caught in other seams or stitching shall be securely backstitched, by overlapping on themselves, for at least 1/2 inch. Thread breaks, skips, and run-Offs shall be over-stitched not less than one inch

38、. The thread tension shall be maintained so that there shall not be any loose or tight stitching and the lock shall be embedded in the materials sewn together. 3.5 Identification labels. Unless otherwise specified, identification labels shall conform to the requirements of Dwg 3214AS205. 3.5.1 Seria

39、l numbers. The soft body armor shall be identified by individual serial numbers which shall be assigned by the manufacturer. Serialization shall be by a block of consecutive numbers to cover the entire acquisition document quantity. 3.6 Markinqs. Unless otherwise specified, the markings shall be leg

40、ible and durable upper case black letters and Arabic numerals and shall be thoroughly dry prior to packaging. The markings shall be lusterless and the letters and numerals shall be sharply defined. The markings shall be accomplished by using such methods and materials as shall be resistant to erasur

41、e or fading under the condition of usage. The marking medium shall not contain any materials which are deleterious to the substance being marked. 3.7 Color. Unless otherwise specified, the color of the soft body armor and components shall conform to applicable drawing requirements. 3.8 Ballistic Dro

42、tection. When tested as specified in 4.7.1, the soft body armor shall conform to the ballistic protection requirements for Type III-A Armor specified in Section 4, Paragraph 4.5 of National Institute of Justice Standard, NIJ0101.03. 3.9 Visual examination. When visually examined as specified in 4.7.

43、2, the soft body armor shall conform to the requirements of this specification and applicable drawings. Classification of defects for visual examination, shall be used to classify the defects. Table VI, 3.10 Dimensional check. When dimensionally checked as specified in 4.7.3, the dimensions of the a

44、ss,embled soft body Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-B-29605 (AS) armor, the dimensions and locations of components, the widths of seams and hems, and the stitching shall conform to applicable drawing requirements. Table VII, Lis

45、t of defects for dimensions of the soft body armor assemblies, shall be used to enumerate the defects . 3.11 Preparation for delivery. When inspected as specified in 4.7.4, the fully prepared shipping containers, containing soft body armor, shall conform to the requirements of this specification. Ta

46、ble VIII, List of defects for packaging, shall be used to enumerate the defects found. 3.12 Workmanship. After completion of the final assembly, the soft body armor shall be thoroughly cleaned and all loose thread, lint, and foreign matter shall be removed. The snap fasteners shall be clinched witho

47、ut distortion, damage, splitting, or cutting of the cloth, webbing, or tape, as applicable. The metal components shall not be misaligned nor contain any sharp edge, crack, dent, nick, burr, or sliver. The soft body armor assemblies shall not contain any non-specified hole, abraded area, tear, cut, m

48、end, needle chew, spot or stain. Drill holes shall be not greater than 1/16 inch in diameter and shall be covered by the component assemblies. The soft body armor assemblies shall conform to the quality and grade of product established by this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 Respo

49、nsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to