NAVY MIL-C-17671 F-1989 CANISTER OXYGEN BREATHING APPARATUS FOR TYPE A-4《A－4型氧气呼吸机滤毒罐》.pdf

1、a * O a -a NIL-C-3767IF 42 W 7777906 0232330 7 = 25 - 09-0 a 11 Mav 1989 SUPERSEDING 23 September 1986 (See 6.8) MIL-C-17671E MILITARY SPECIFICATION CANISTER, OXYGEN BREATHING APPARATUS, FOR TYPE A-4 This specification is approved for use by all Departments and Agencies of the Department of Defense.

2、 1. SCOPE 1.1 Scope. This specification covers a canister for the type A-4 oxygen breathing apparatus (OBA). 1.2 Part number. The part number for the canister covered by this speci- fication shall be M17671-1. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications. standards, and han

3、dbooks. The following specifica- tions, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supple

4、ment thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL PPP-B-636 - Boxes, Shipping, Fiberboard. PPP-B-640 - Boxes, Fiberboard, Corrugated, Triple-Wall. Beneficial comments (recommendations, additions, deletions) and any pettinent data whic.h may be of use in improving this documen

5、t should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. THIS DOCUMENT CONTAINS !q PAGES. AM

6、SC N/A FSC 4240 DISTRIBUTION STATEMENT A. Approved-for public- release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-17bLF qi? = 733970b 0232311 7 I MIL-C-17671F MILITARY MIL-P-116 - Preservation, Methods of. 1 * S

7、TANDARDS FEDERAL FED-STD-313 - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities. FED-STD-595 - Colors. MI LI TARY MIL-STD-129 MIL-STD-147 - Palletized Unit Loads. MIL-STD-171 - Finishing of Metal and Wood Surfaces. - Marking for S

8、hipment and Storage. (Uriless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Canter, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Other Government documents, drawings. and publi

9、cations. The followi.ng other Government documents, drawings, and publications form a part of this document: to the extent specified herein. Issues are those cited in the solicitation. Unless otherwise specified, the DRAWING I NAVAL SEA SYSTEMS COMMAND (NAVSEA) 803-5184258 - Oxygen Breathing Apparat

10、us, Canister, Quick Starting . (Application for copies should be addressed to the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) PUBLICATION I DEPARTMENT OF HEALTH AND HUMAN SERVICES, NATIONAL INSTITUTE FOR OCCUPATIONAL SAFETY AND HEALTH (NIOSH)

11、85-114 - Pocket Guide to Chemical-Hazards (Application for copies should be addressed to Superintendent of Documents, I U.S. Government Printing Office, Washington, DC 20402.) 2.2 Order of Drecedence. In the event of a conflict between the text of this document and the references cited herein, the t

12、ext of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.4) in accord

13、ance with 4.3. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-C-1767LF 42 W 777770b 0232312 O MIL-C-17671F 3.2 Design and details. The design of the canister shall be in accordance with Drawing 803-5184258. source of breathable gas. The canis

14、ter shall not utilize compressed gas as a 3.3 Markinns. - Markings on the canisters shall be in accordance with Drawing 803-5184258. of the burn hazard when unprotected skin is exposed to the canister. A caution shall be imprinted on the canister label warning 3.4 Canister Derformance. 3.4.1 Caniste

15、r outout. The canisters shall maintain breathable gas continuously without deliberate additional user action for a minimum of 30 or 60 minutes after initiation of the starting process (see 4.6.2.2). shall be defined as not less than- 20.0 (dry atmosphere) volume percent oxygen. The breathable gas sh

16、all contain no impurity in excess of the exposure limit defined in NIOSH 85-114. generate gas, smoke, or other products which will have any harmful physiological effect on personnel under any conditions of use. volumetric content of the gas shall conform to the limits as specified (see 4.6.2.2.1). T

17、he gas temperature when measured as specified (see 4.6.2.2.3) shall be less than 115F (46C) dry bulb and 105F (40C) wet bulb. Breathable gas The canister shall contain no impurities which will The average carbon dioxide 3.4.1.1 Canister surface temverature. The external surface temperature of the ca

18、nister, with the exception of the ignition components of the breathable gas starting process, shall not exceed 475F (246C) during the gas evolution process (see 4.6.2.3). primer) shall not exceed 475F after 5 minutes after the breathable gas starting process is initiated. The surface temperature of

19、ignition components (such as the 3.4.1.2 Mois.ture. The humidity content of the gas shall be sufficiently low to preclude condensation forming upon the OBA facepiece lens (fogging) and collection of liquid in the breathing bag and hoses (see 4.6.2.4). be defined as moisture which forms and obscures

20、the wearers vision and persists for more than 4 consecutive seconds. Fogging shall 3.4.2 Gasflow resistance. Prior to performance testing, the resistance of each fully assembled canister to gasflow shall be not greater than 0.72 inch (18 millimeters (mm), of water column height when tested as specif

21、ied (see 4.6.2.1). 3.5 Breathable gas - starting: Drocess. The canister shall contain a breath- able gas starting process which rapidly supplies breathable gas at the beginning of canister use. 3.5.1 Overall requirements. The starting process shall operate within an ambient temperature range of minu

22、s 22 to 212F (minus 30 to 100C) (see 4.6.3.1 and 4.6.3.2). The process shall supply a minimum of 0.088 cubic foot (2.5 liters (L) of breathable gas at standard temperature and pressure (STP), 30.4 inches (760 mm) mercury, 32F (OOC), in the first minute of operation and shall continue to evolve breat

23、hable gas until 0.334 cubic foot (9.5 L) of breathable gas at STP have been evolved within a maximum of 3.5 minutes. When the process is initiated at 212“F, it shall evolve 0.354 cubic foot of breathable gas at STP in not less than 45 seconds, less than 0.02 percent by volume (see 4.6.3.3). Carbon m

24、onoxide generated from the starting process shall be 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-17671F 3.5.2 Sparking. The breathable gas starting process shall be non-sparking (see 4.64). 3.5.3 Salt spray. The breathable gas starting pr

25、ocess shall be resistant to salt water (see 4.6.5). 3.6 Weight. The fully assembled canister shall weigh not more than 75.4 ounces (2155 grams). 3.7 Color. The color of the canister shall be green, in accordance with color nimber 14110 or 14187 of FED-STD-595 and as specified on Drawing 803-51.84258

26、. 3.8 Finish. The finish for the canister shall be in accordance with finish ntmbor 22.9 of MIL-STD-171 and as specified on Drawing 803-5184258. 3.9 Identification. The bottom of each canister shall be permanently Imprinted with the lot number and date of manufacture. number skall. be applied to the

27、 canister. A label with the contract 3.10 Material safety data sheet (MSDS) The contracting activity shall be provided rz material safety data sheet at the time of contract award. shall be provided in accordance with the requirements of FED-STD-313. c1ia11. be included with each shipment of the mate

28、rial covered by this specifi- cation (cee 6.5). The MSDS The MSDS 4, QUALITY ASSURANCE PROVISIONS 4.1. Responsibility for inspection. Unless otherwise specified in the contract: (ar purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tes

29、ts) as specified herein. Except os otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government: reserves the right to p

30、erform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conorm to prescribed requirements. 4.1.1 Responsibilitv for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in thi

31、s specification shall become a part o the contractors overall inspection system or quality program. absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance

32、comply with all requirements cf the contract. Sampling inspection, as part of the manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the

33、Government to accept defective material. The 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: (a) (b) First article inspection (see 4.3). Quality conformance inspection (see 4.4). 4 Provided by IHSNot for ResaleNo reproduction or networking p

34、ermitted without license from IHS-,-,-WIL-C-37673F 92 m 77977clb 023233Ll 4 Examination or test Requirement Test Canister weight 3.6 4.6.1 Visual and dimensional 3.2, 3.3, 3.7, 4.5 examination 3.8 and 3.9 MIL-C-17671F Number tested 40 40 4.3 First article inspection. One hundred sample canisters sha

35、ll be furnished for first article inspection when specified (see 6.4). fails any examination or test, it shall constitute failure of first article inspection (see 6.3). If any sample 4.3.1 For examinations and nondestructive test. Forty canisters shall be randomly selected from the 100 sample canist

36、ers, and subjected to the examina- tions and test in table I. TABLE I. First article inspection (examinations and nondestructive test). TABLE II. First article inspection (destructive tests). Test Resistance to gasflow Duration Performance purity Temperature of canister External surface Mo is tur e

37、Breathable gas starting process produced gas temperature Breathable gas evolution Breathable gas evolution at minus 22F (minus 30C) at 212F (lOOC) Pur i ty Canister sparking Salt spray Requirement 3.4.2 3.4.1 3.4.1 3.4.1 3.4.1.1 3.4.1.2 3.5.1 3.5.1 3.5.1 3.5.2 3.5.3 Test 4.6.2.1 4.6.2.2.1 4.6.2.2.2

38、4.6.2.2.3 4.6.2.3 4.6.2.4 4.6.3.1 4.6.3.2 4.6.3.3 4.6.4 4.6.5 Number tested 13 13 13 13 13 2 13 13 13 13 13 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-17b71F LI2 W 4740b 0232315 b Examinations and test Requirement Canister weight 3.6 Vis

39、ual and dimensional 3.2, 3.3, 3.7, 3.8 examination and 3.9 MIL-C-17671F Test 4.6.1 4.5 4.4 Qunlitv conformance inspection. Quality conformance inspection shall consist of the visual and nondestructive examination specified in 4.4.1.1 and group A and D tests specified in tables III and IV. Group B an

40、d C tests are not applicable. Test specified in 4.6.4 and 4.6.2.2.2 need to be tested on only one random sample per lot and tests specified in 4.6.3.1 and 4.6.3.2 need only be eonducted on two random samples per lot. Tests specified in 4.6.5 need be tested on only two canisters from every 20 lots to

41、 validate conformance to requirements. TABLE IV. Group D tests. Test External surface Temperature of canister Canister sparking Resistance to gasflow Duration . Performance purity Breathable gas starting temperature produced gas process Breathable gas evolution Breathable gas evolution at minus 22F

42、(minus 30C) at 212F (100C) Salt spray Requirement 3.4.1.1 3.4.1 3.5.2 3.4.2 3.4.1 3.4.1 3.5.1 3.5.1 3.5.3 Test 4.6.2.3 4.6.2.2.3 4.6.4 4.6.2.1 4.6.2.2.1 4.6.2.2.2 4.6.3.1 4.6.3.2 4.6.5 4.4.1 m. A lot shall consist of all completed canisters produced under the same conditions and offered for inspecti

43、on at one time with quantity not to exceed 3,200 canisters. 4.4.1.1 Samnling for examination. A random sample of assembled canisters shall be selected from each lot for the examination specified in table V. Sampling shall be in accordance with table VI for major defects and table VI1 for mirisr defe

44、cts. acceptance number for that sample, the lot represented by the sample shall be rejected. offered for delivery. If any item contains a critical defect, the entire lot shall be rejected. If the number of nonconforming items in any sample exceeds the Any item in the sample found to have one or more

45、 defects shall not be 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a Lot size 2 to 15 16 to 50 51 to 150 151 to 500 501 to 3200 Categories Sample size Acceptance number 2 O 3 O 5 O 8 1 13 1 MIL-C-37673F q2 7777706 0232336 MIL-C-17671F TABLE V. C

46、lassification of defects. Critical : 1 Major: 101 102 103 104 105 106 107 Minor : 201 202 203 TABLE VI. Sampling - plan for maior defects. Defects Evidence of oil, grease, or flammable substances. Breathable gas starting process defective or damaged. Lot number, date of manufacture, or contract numb

47、er Instruction markings missing, illegible, incorrect, or Identification and caution markings missing, illegible, Finish missing, incomplete, damaged, or not as specified. Body and neck bent, cracked, or not as specified. Fully assembled canister which is in excess of 75.4 missing. not as specified.

48、 incorrect, or not as specified. ounces. Tear-off cap defective, not secure on neck, or not as Color not as specified. Workmanship not as required. specified. Lot size I Sample size I Acceptance number I 2 to 15 16 to 50 51 to 150 151 to 500 501 to 3200 2 3 5 8 13 O O O O O ! TABLE VII. Sampling pla

49、n for minor defects. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-L7671F 42 9979906 0232317 T MIL-C-17671F 4.4.1.2 SamDling for tests. 4.4.1.2.1 SamDlinP for grouri A examinations (nondestructive). Tests specified in table III shall be sampled as specified in 4.4.1.1 and table VI. 4.4.1.2.2 Sampling for group D tests (destructivel. A rando