NAVY MIL-DTL-85855 A-1999 VALVE QUICK DISCONNECT FOR THE PROTECTIVE ASSEMBLY CHEMICAL BIOLOGICAL RADIOLOGICAL (CBR) A P22P-9(V)《为保护组件快速断开阀门的生物化学放射性武器》.pdf

1、I INCH-POUND I MIL-DTL-85855A(AS) 25 October 1999 SUPERSEDING 6 November 1989 MIL-V-85 855(AS) DETAIL SPECIFICATION VALVE, QUICK DISCONNECT, FOR THE PROTECTIVE ASSEMBLY, CHEMICAL, BIOLOGICAL, RADIOLOGICAL (CBR), A/P22P-9(V) This specification is approved for use by the Naval Air Systems Command, Dep

2、artment of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification establishes the requirements for a quick disconnect valve for the protective assembly, chemical, biological, radiological (CBR), A/P22P-9(V). 2. APPLICAB

3、LE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to

4、ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be

5、 of use in improving this document should be addressed to: Commander, Naval Air Warfare Center Aircraft Division, Code 4 14 1 OOB 120-3, Highway 547, Lakehurst, NJ 08733- 5 100, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by lett

6、er. AMSC NIA FSC 4240 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.2 Government documents. 2.2.1 Specifications, standards and handbooks. The following specificati

7、ons, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicita

8、tion (see 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-A-8625 - Anodic Coatings for Aluminum and Aluminum Alloys. MIL-N-18307 - Nomenclature and Identification for Aeronautical Systems Including Joint Electronics Type Designated Systems and Associated Support Systems. STANDARDS FEDERAL FED-STD-595

9、 - Colors used in Government Procurement. DEPARTMENT OF DEFENSE MIL-STD- 1 O0 - Engineering Drawings. MIL-STD- 130 - Identification Marking of U.S. Military Property. MIL-STD-282 - Filter Units, Protective Clothing, Gas-Mask Components MIL-STD-8 1 O - Environmental Engineering Considerations and Lab

10、oratory MIL-STD-889 - Dissimilar Metals. and Related Products: Performance-Test Methods. Tests. HANDBOOKS MIL-HDBK-3 1 O - MIL-HDBK-505 - Definitions of Item Levels, Item Exchangeability, Models, and MIL-HDBK-695 - Rubber Products: Recommended Shelf Life. Global Climatic Data for Developing Military

11、 Products. Related Terms. (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19 1 1 1-5094.) 2 Provided by IHSNot for ResaleNo reproduction or networki

12、ng permitted without license from IHS-,-,-2.2.2 Other Government documents. The following Government document forms a part of this document to the extent specified herein. Unless otherwise specified, the issue is that cited in the solicitation. Army Field - NBC Decontamination. Manual FM 3-5 (Copies

13、 of Army Field Manual FM 3-5 are available from the Commander, US Army Publishing Agency, 2461 Eisenhower Avenue, Alexandria, VA 2233 1 .) 2.3 Non-Government publication. The following document forms a part of this document to the extent specified herein. Unless otherwise specified, the issue of the

14、 document which is DoD adopted is listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issue of the document not listed in the DoDISS is the issue of the document cited in the solicitation (see 6.2). SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE-AMs3238 - Butyl (I

15、IR) Rubber, Phosphate Ester Resistant, 65-75. (Application for copies should be addressed to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the

16、text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), samples shall be subjected to first article inspection in accordance with

17、4.2. 3.2 Materials. Materials shall be corrosion resistant or treated to resist corrosion due to fuels, salt spray, environmental, chemical, or biological warfare conditions. 3.2.1 Aluminum alloy. Aluminum alloy parts shall be anodically treated as specified in MIL-A-8625. 3.2.2 Dissimilar metals. D

18、issimilar metals shall not be used in intimate contact with each other. Dissimilar metals shall be as defined in MIL-STD-889. 3.2.3 Non-metallic materials. Rubber seals and O-rings shall meet the requirements specified in SAE-AMs3238 and the requirements specified herein (see 3.5.7). 3 Provided by I

19、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.2.4 Fungus-proof materials. All materials shall not support fungoid growth. 3.2.5 Age. Elastomeric components shall have a shelf life of greater than 5 years in accordance with MIL-HDBK-695 when consistent with th

20、e properties required for functionality 3.2.6 Toxic materials. The use of materials which produce toxic effects under any conditions shall not be used. 3.2.7 Flammable materials. The use of materials which will support combustion shall not be used. 3.3 Desim and construction. The quick disconnect va

21、lve shall be designed and constructed as shown on figure 1. The valve shall form part of the A/P 22P-9(v) Protection Assembly as shown in figure 2. The valve shall be installed in-line between the mask and tactical ventilator to provide emergency egress and quick disconnection during ground operatio

22、ns and water landings. Design and construction shall permit decontamination of external surfaces without damage to or deterioration of the valve or its protective capability using materials and procedures of Army FM 3-5. The valve shall be compatible with oxygen and oxygen systems of Naval Air Syste

23、ms Command and prevent ingress of all forms of contamination. 3.3.1 Storage life. The quick disconnect valve shall be designed to meet the performance requirements herein after five years storage under worldwide climatic conditions specified in MIL-HDBK-3 1 O. 3.3.2 Interchangeability. All parts, as

24、semblies and subassemblies, having the same part number, shall be identical as specified in MIL-HDBK-505 and MIL-STD-100. When any unit or part is interchanged, the quick disconnect valve shall meet all performance requirements without adjustment or modification of any part or subassembly. 3.4 Hardw

25、are. 3.4.1 Fasteners. All fasteners, including bolts, screws, nut, rivets, and washers shall be selected from the fasteners listed in the Department of Defense Index of Specifications and Standards (DoDISS). 3.5 Performance. 3.5.1 Separation force. The valve shall withstand the separation force requ

26、irements in the unlocked and locked positions as follows. 3.5.1.1 Unlocked. The maximum axial force required to separate the quick disconnect valve at the quick disconnect fitting shall be not greater than five pounds (22.2 newtons) when tested as specified in 4.5.2.1.1. 4 Provided by IHSNot for Res

27、aleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-S5855A(AS) da oz 52 w3 a0 mo Fi; w a c ce H a O z U ci-a P W LL FIGURE 1. Quick disconnect valve. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n ICATION CANTEEN PURP

28、OSES) (ILL Us TRATIVE FIGURE 2. Protective assembly, CBR, helicopter aircrew member. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.5.1.2 Locked. The quick disconnect valve shall not separate at the quick disconnect fitting while in the locked p

29、osition under a minimum axial force of 100 pounds (440.0 newtons), when tested as specified in 4.5.2.1.2. 3.5.2 Self sealing valve. The force required to open the self-sealing valve, contained within the male portion of the quick disconnect valve, shall be not greater than four pounds (17.8 newtons)

30、 when tested as specified in 4.5.2.2. 3.5.3 Air leakage. The overall leakage rate of the quick disconnect valve shall be not greater than 0.006 cubic inch/min (O. 10 cc/min) when tested for suction or pressure as specified in 4.5.2.3.1 and 4.5.2.3.2. 3.5.4 Pressure drop. The pressure drop through th

31、e quick disconnect valve shall be not greater than 0.5 inch water gauge (WG) when tested as specified in 4.5.2.4. 3.5.5 Water leakage. The self-sealing valve shall be water-tight (zero leakage) when tested as specified in 4.5.2.5. 3.5.6 Noise level. The noise level, measured with the quick disconnec

32、t valve connected to the CQK-2/P tactical ventilator delivery hose outlet, shall be not greater than the noise levels shown on figure 3 as determined by 1/3 octave band analysis over the frequency range 200-5000 Hz when tested as specified in 4.5.2.6. 3.5.7 Chemical agent penetration. The coupling s

33、eals and O-ring materials of the quick disconnect valve shall have an endpoint time of not less than 360 minutes when tested as specified in 4.5.2.7.1, 4.5.2.7.2, and 4.5.2.7.3. 3.5.8 Endurance. Prior to and upon completion of the endurance test of 4.5.3, the quick disconnect valve shall meet the re

34、quirements of 3.5.1, 3.5.2, 3.5.3, and 3.5.4 without failure after 500 cycles when tested as specified in 4.5.3. 3.5.9 Environmental. The quick disconnect valve shall meet the requirements of 3.5.1, 3.5.2, 3.5.3, 3.5.4, and 3.5.5 prior to and at the completion of each environmental test of 4.5.4. 3.

35、5.9.1 Hi& temperature. The quick disconnect valve shall operate without failure when tested as specified in 4.5.4.1. 3.5.9.2 Low temperature. The quick disconnect valve shall operate without failure when tested as specified in 4.5.4.2. 3.5.9.3 Salt fog. The quick disconnect valve shall withstand bot

36、h the corrosive and physical effects of the salt fog environment and operate without failure when tested as specified in 4.5.4.3. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-90 80 h a 70 cl W cl 9 2 E D 60 Ml Ml W 50 O Ml 40 30 oomoooooooooooo

37、omoomoomooomoo clclmTtm clclmTtmooo omdoo 1/3 OCTAVE BAND CENTER FREQUENCY (Hz) FIGURE 3. Noise levels at quick disconnect valve with 100 LPM air flow. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.5.9.4 Icing/fi-eezing rain. The quick disconne

38、ct valve shall withstand the effects of icing produced by a freezing rain and shall operate without failure when tested as specified in 4.5.4.4. 3.5.9.5 Funws. The quick disconnect valve shall not support fwigal growth and shall operate without failure when tested as specified in 4.5.4.5. 3.5.9.6 Lo

39、w pressure/high humidity. The quick disconnect valve shall operate without failure when tested as specified in 4.5.4.6. 3.5.9.7 Dust. The quick disconnect valve shall withstand the effects of blowing dust and shall operate without failure when tested as specified in 4.5.4.7. 3 59.8 Normal accelerati

40、on. The quick disconnect valve shall not inadvertently disconnect and shall operate without failure when tested as specified in 4.5.4.8. 3.5.9.9. Hi& temperature/diurnal cycle/high humidity. The quick disconnect valve shall operate without failure when tested as specified in 4.5.4.9. 3.6 Component p

41、arts. The quick disconnect valve shall consist of a male portion and a female portion (see 3.6.1 and 3.6.2). 3.6.1 Male portion. The male portion (see figure 1) of the quick disconnect valve shall be attached to the air inlet hose of the MCK-3/P mask and shall contain a self-sealing valve which auto

42、matically closes when the two portions are separated. The self-sealing valve shall be able to be opened by a CBR protected, gloved hand when the quick disconnect is separated to allow air to flow freely into the mask. 3.6.2 Female portion. The female portion (see figure 1) of the quick disconnect va

43、lve shall be attached to the CQK-2/P tactical ventilator delivery hose and shall contain a single action one-hand operated, locking mechanism to prevent inadvertant disconnection and to allow for quick disconnection with one CBR protected gloved hand. 3.7 Dimensions. The overall length of the quick

44、disconnect valve shall be not greater than five inches. The outside diameter shall be not greater than 1.5 inches. 3.8 Wei&. The weight of the quick disconnect valve shall be not greater than eight ounces. 3.9 Color. The quick disconnect valve shall be black in color, approximately matching color nu

45、mber 37038 of FED-STD-595. 3.1 O Nameplates and identification markings. Nameplate approval, equipment identification marking, and serial number assignment, shall be as specified in MIL-N-18307 and MIL-STD-130. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

46、om IHS-,-,-3.1 1 Workmanship. The quick disconnect valve shall be free from contamination and imperfections such as dirt, grease, oil, foreign matter, malfunctioning of hardware and damage such as cracks, burrs, sharp edges, rough grinding marks, and uneven surfaces due to forming operations. Rubber

47、 parts shall be free of damage, cuts, and tears. Particular attention shall be given to accuracy of dimensions, fillet radii, marking of parts and assemblies, thoroughness of welding, brazing, painting, swaging, and soldering, alignment of parts, and tightness of assembly screws and bolts. 4. VERIFI

48、CATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.2). b. Conformance inspection (see 4.3). 4.2 First article inspection. First article inspection shall be performed on three quick disconnect valves whe

49、n a first article sample is required (see 3.1). This inspection shall be completed in the order specified in table I. 4.3 Conformance inspection. Conformance inspection shall consist of all the examinations and tests specified in table II. 4.4 Test conditions. 4.4.1 Temperature and pressure. Inspections shall be conducted at local ambient temperature and barometric pressure. Corrections shall be m