NAVY MIL-P-23004 A-1964 POD (FOR GUN POD MARK 4 MOD 0)《标号4 MOD 0)下船港枪支》.pdf

1、- - ,/- -_ - - - MIL-P-23004A (Wep) 13 March 1964. MIL-P-23004 (Wep) 21 August i961 SUPERSEDING MILITARY SPECIFICATION POD (FOR GUN POD MARK 4 MOD O) 1. SCOPE 1.1 SCO e. This specification covers Pod (for Gun Pod Mark d O), referred to herein as the pod. 2 . APPLICABLE DOCUMENTS 2.2 date of invitati

2、on for bids form a part of this specifi- cation to the extent specified herein. SPECIFICATIONS The following documents of the issue in effect on Military MIL-W- 5088 MIL-C-5501 MIL-P-5518 MIL-E-7080 MIL-A=8 591 Wiring, Aircraft, Installa- tion of. Caps and Plugs, Protective, Dust and Moisture Seal.

3、Pneumatic Systems, Aircraft; Design, Installation, and Data Requirements for. Test Procedures for Aircraft Hydraulic and Pneumatic Sys- tems, General . Electric Equipment, Piloted Aircraft, Installation and Selection of, General Speci- fication for. Airborne Stores and Associated Equipment; General

4、Design Criteria for. /- THIS DOCUMENT CONTAINS ld PAGES. I FSC 10051 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-23004A LO U 7777906 0302720 L H - - MIL-P-2 3004A STANDARDS Military ILSTD=O MIL-STD-12 9 MIL- S Dl43 MIL-STD-7OLb DRAWINGS l3u

5、rea,u of Naval Wea ns (Code Ident 10001 p“ LD 416841 LD 416842 LD 416846 LD 416850 LD 522078 LD 522079 LD 615425 LD 615432 LD 615434 LD 539673 LD 615435 982519 14.165196 PUBLICATIONS Military Military Iiandbook E Charao- teristics and Utilization of. Container, Shipping and Storage, for Tail Assembl

6、y. Container, Shipping and Storage, for Nose Assembly. Container, Shipping and Storage, for Reservoir Assembly, Feed Chutes, and Ejection Tubes. Container, Shipping and Storage, for Gun Pod Body. Gun Mechanism, ZOMM, Mark 11 Mod 5. Loader, Gun, 20MM, Mark 2 Mod 1, Pod (Assembly) . Link, Ammunition,

7、Mark 6 Mod 4. Kit, Gun Pod Accessories. Link, Ammunition, Leading, Mark 6 Mod 5. Link, Ammunition, Trailing, Mar Descrip- tion, Operation, and Main- tenance, Quality Assurance Provisions for Gun Pod Mark 4 Mod O. (Copies of documents required by contractors in connec- tion with specific procurement

8、functions should be ob- tained from the procuring activity or as directed by the contracting officer. ) 3. REQUIREMENTS 3.1 Preproduction sample. %less otherwise specified in the contract or order, a preproduction sample of pods shall be delivered for testing at a facility designated in the contract

9、 or order (see 6.2). The preproduction sample shall be manufactured using the methods proposed for production. approval of the preproduction sample shall be at the suppliers risk. Any production by the supplier prior to 3.2 Compliance with documents. Unless otherwise speci- fied, the pod shall be in

10、 accordance with the require- ments specified herein and in the applicable documents listed in section 2. 3.3 Materials. Materials used in the manufacture of the pod shall conform to the material specfoations in the applicable dOGUmentS listed in section 2. Subject to the approval of the Government

11、representative, alternate materials may be selected in accordance with Military Handbook Hl in the order of precedence specified in Standard 3.4 Desim. with the requirements specified herein and in the ap- plicabXe documents listed in section 2. The pod shall be assembled with other components of th

12、e Mark 4 Gun Pod and prepared for operation as speoified in Publication OP 2719. The pod shall meet the requirements of 3.4.1 through 9.4.5. 3.4.1 Safety. When the switch controlling the gun pod clearing function is actuated, the pod shall supply MILSTD=i43. The design of the pod shall be in accorda

13、nce -. 3 -7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-electric power and compressed air to the gun mechanism and loader to disengage the leader sprocket from the gun mecha- nism. The pod shall cycle the gun mechanism not fewer than three times

14、in 500 milliseconds, ejecting cartridges or cartrige cases with a velocity sufficient to pass through the loader and the pod ejectioa tubes without catching or binding. 3.4.2 Function. 3.4.2.1 Pianua1 charainq. When the switch controlling the gun pod charging function is actuated, the pod shall cycl

15、e the gun mechanism to carry rounds from the ram position to firing position. Any cartridges or cartridge cases at the eject position shall be ejected with a velocity sufficient to clear incoming links and to pass through the eJection tubes without catching or binding. 3.4.2.2 Automatic charging. Wh

16、en the pod electrical sys- tem is wired for automatic charging and the gun fails to fire when the firing oircuits are energized, the pod shall supply signals and power to the gun for automatic charging within 200 milliseconds. Live rounds shall be cycled into firing position and any rounds or cases

17、at the eject Sta- tion shall be ejected. 3.4.2.3 Rate of fire. A switch shall be provided in the pod junction box to preselect the rate of fire of the gun pod. minute plus or minus 200 rounds per minute. of fire shall be 700 rounds per minute plus or minus 100 rounds per minute. 3.4.3 Life. 3.4.3.1

18、Operational life. The pod shall be capable of feeding l30,OOO service rounds and firing the same number through the gun mechanism with normal parts replacement and servicing. The parts replacement schedule shall be as specified in Publication OP 2719. 3.4.3.2 Shock and vibration. When preserved and

19、packaged (see section 51, the pod shall withstand shocks, impacts from accidental dropping, and vibrations of logistic hand- ling and transportation without damage. 3.4.3.3 Storage life. When preserved and packaged, the pod shall be capable of storage without deterioration for The normal rate of fir

20、e shall be 4000 rounds per The slow rate Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-2 3004A not less than three years. 3.4.4 Interchangeability, All pod component parts which are n0.t; formed into inseparable assemblies shall be capable of

21、 assembly without selection or fitting at industrial fa- oilities and at the fleet level. 3.4.5 Coordination, 3,4.5.1 Service ammunition. The pod shall feed, cycle, and fire service ammunition in the Mark 100 series. 3,4.5.2 Aircraft The pod shall assemble with the 20NM Aircraft Gun “k 11 Mod 5 with

22、out selection.or fitting. 3.4.5.3 COHL nents. The electrical and pneumatic com- ponents o + the pod shall be capable of nonselective con- nestion with those of the gun mechanism, 3.5 Construction. 3.5.1 Elector reinforcement, The ejector reinforcement of the pod shall meet the applicable requirement

23、s of fig- ure 4 of Specification MIL-A-8591, 3.5.2 Sway brace reinforcement. The sway brace rein- forcement of the pod shall meet the applicable require- ments of figure 4 of Specification MIL-A-8591. 3.5.3 Cradlinp; reinforcement, The oradling reinforce- ment of the pod shall meet the applicable re

24、quirements of figure 5 of Specification MIL-A-8591. 3.6 Details of components. 3.6.1 mectrical system. 3.6.1.1 External power, The pod shall conform to Stand- ard MIL-STD-704, and shall meet all other requirements of this specification when furnished with external power as defined in Swndard MIL-STD

25、-704 and as follows: A 28 volt plus or minus 4.0 volt direct current, negative grounded power source capable of deliver- ing not less than 7.0 amperes during charging. A 120/208 volt, three-phase, 400 cycle alternating current power source capable of delivering not less than 2.0 amperes per phase on

26、 two phases during firing or 120 volt single phase at 4.0 amperes. (a) (b) 5 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-2 3004A 3.6.1.2 Wiring and installation. The pod shall be capable of meeting the requirements of this specification w

27、hen wired in accorance with Specification MIL-W-5088 and installed in accorance with Specification MIL-E7080. ments of Specification MIL-B-5087 are not applicable to this specification. 3.6.1.3 Induced voltage. There shall be no induced volt- age in the pod electrical system at any time which could

28、energize the firing circuits and accidentally fire ammu- nition. The require- 3.6.2 Pneumatic system. 3.6.2.1 Tube assemblies. All tube assemblies shall with- stand a proof pressure of 6000 psig plus or minus 100 psig and shall meet the requirements of Specification MIL-P-5518. 3.6.2.2 Leakage. When

29、 the cutoff valve is closed, pres- sure loss measured at the reservoir assembly shall not ex- ceed 25 psig in 24 hours. When the cutoff valve is open, pressure loss measured at the reservoir assembly shall not be more than 100 psig in 24 hours. 3.6.2.3 System proof pressure. Upstream of the pressure

30、 regulator, the pod system shall withstand a proof pressure (relief reseat pressure) of 3300 psig plus or minus 100 psig. When the pressure regulator is set as specified in Drawing 2094307, the system shall withstand a proof pres- sure (lockup pressure) downstream of the regulator of 1500 psig maxim

31、um. 3.7 Performance characteristics. When tested as speci- fied in 4.6.3.1, the pod shall withskand the firing of the complete contents of four ammunition magazines without a stoppage, and shall meet the requirements of 3.4.2. 3.8 Temperature extremes. The pod shall meet the require- ments of 3.4.1

32、and 3.4.2 at any temperature between minus 65 degrees Fahrenheit (F.) and 165 degrees F. 3.9 Government-furnished property. The following, in quantities specified in the contract or order, are required to determine compliance of the pod with the requirements of this specification: Dummy Rounds, 20MM

33、, Mark 104 Mod O. bj Target Practice Rounds, 20MM, Mark 105 Mod O. (a) Ammunition Links, Mark 6 Mods 4, 5, and 6. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-2 300bA 3.10 Government-loaned property. The following are re- quired to test the

34、pod for conformance to the require- ments of this specification: (a) Gun Mechanism, 20MM, Mark 11 Mod 5. (b) Loader, Gun, 20MM, Mark 2 Mod I, c) Ejector Rack Assembly, Aero 7A-1, or equal, d) Installation Kit Mark 4 Mod O Gun Pod (Drawing 24714521, or kit matching (c) . (e) Kit, Gu Pod Accessories.

35、3.11 Worknanship. The quality of workmanship on pod com- ponents and on the assembled pod shall assure conformance to all of the requirements of this specification. assembly of pod components into the pod shall be as spec- fied in FublIcation OF 2719, 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibili

36、ty for inspection. Unless otherwise specified in the contract or order, the supplier is re- sponsible for the performance of all inspection require- ments as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commer- cial laboratory acceptable to the

37、Government. The Govern- ment reserves the right to perform any of the inspections set forth in this specifcation where such inspections are deemed necessary to assure that supplies and servioes conform to prescribed requirements. 4.2 Classification of tests. The inspection and testing of the pod sha

38、ll be classified as follows: The Preproduction tests . Acceptance tests, 4.3 Lot. Lut definition, size, and formation shall be as spxfied in Standard MIL-STD1O5. 4.4 Samplinq. Unless otherwise specified herein, the provisions set forth in Standard MIL-STD15 shall govern the establishment of sampling

39、 plans and procedures for in- spection by attributes, 4.5 Examination. kC;,l Components. Prior to assembly of the pod, it shall be ascertained that all components procured under separate documents have been inspected, tested and accepted in RC , k I 7 I 7 .k Provided by IHSNot for ResaleNo reproduct

40、ion or networking permitted without license from IHS-,-,-MIL-P-2 3004A accorance with their respective documents. 4.5.2 Packiw and marking. It shall be ascertained that packing and marking of the pod conform to section 5 of this specification. 4.6 Tests. 4.6.1 Acceptance tests. Sample pods, seleoted

41、 In ao- cordarice with 4.4, shall be subjeoted to the acceptance tests specified herein except that the tests of 4.6.1.3, 4.6b.4, 4.6.1b5, and h.6.i.6 shall be performed on each pod component or pod intended for delivery to the Govern- ment. Lot quality shall be as specified in 4.6.2. 4.6.1.1 Visual

42、 and mechanical inspection. The pod and gmd components shall be examined for conformance to 3.2, 3.3, and 3.11. 4.6.1.2 Pneumatic test procedure. The supplier shall prepare a pneumatic test procedure and shall submit test reports in accordance with the requirements of Specifi- cation MIL-T-5522. 4.6

43、.1.3 Tubina pressure tests. Prior to assembly into the pod, all tube assemblies shall be subjected to proof pres- sure tests in a burst chamber approved by the Government representative. The tube assemblies shall meet the re- quirements of 3.6.2.1. Following the tests, the tube assemblies shall be d

44、egreased and dust caps conforming to Specification ML-C-Cj501 shall be installed. 4.6.i.4 Leakage tests. With the manually operated valve in the off position, charge the pneumatic reservoir as specified in the instructions shown on the plate attached to the reservoir. After charging, the assembled p

45、od shall be allowed to stand for not less than four hours. Record temperature and pressure at the reservoir at the end of the four hour period. Read the temperature and pressure at the reservoir. After making a temperature-pressure correction, record the temperature and the corrected pressure. If pe

46、rmitted leaka e does not conform to the applicable requirements mine the leakage source. Recharge the reservoir to the specified pressure and allow the pod to stand for not less than two hours. Record temperature and pressure at the reservoir and open the manually operated valve. Allow the pod to st

47、and for 24 hours. of 3. z .2.2, apply soap solution to the fittings to deter- Allow 8 *A . ?-) . . I .:. .- I :, ! -, , - .- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P=2 3004.A the pod to stand for 24 hours and repeat th test procedure spe

48、cified herein. ment representative, an alternate method of determining leakage may be substituted. 4.6.1.5 System pressure test. The proof pressure require- ment of 3.6.2.3 shall be verified at the same time that the tests of 4.6.i.4 are performed. Defective components shall be isolated by applicati

49、on of soap solution and shall be replaced. 4.6.1.6 Clearing test. The gun mechanism and loader shall be installed in the pod as specified in Publication OP 2719. !I!he clearing switch shall be actuated. form to 3.4.1. 4.6.i.7 Function tests. Gun pod components shall be as- sembled and prepared for operation as specified in Publi- cation OP 2719, except that the magazine shall be loaded with two belts o