NAVY MIL-PRF-16552 F-2001 FILTERS AIR ENVIRONMENTAL CONTROL SYSTEM CLEANABLE IMPINGEMENT (HIGH VELOCITY TYPE)《(高压型)冲击可清洁空气环境控制系统过滤器》.pdf

1、Beneficial comments (recommendations, additions, deletions) and any pertinentdata which may be of use in improving this document should be addressed to:Commander, SEA 05Q, Naval Sea Systems Command, 1333 Isaac Hull Ave, SE,Washington Navy Yard, Washington DC 20376 by using the StandardizationDocumen

2、t Improvement Proposal (DD Form 1426) appearing at the end of thisdocument or by letter.AMSC N/A FSC 4130DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDMIL-PRF-16552F01 June 2001SUPERSEDINGMIL-F-16552E (SH)28 October 1986PERFORMANCE SPECIFICATIONFILTERS, A

3、IR ENVIRONMENTAL CONTROL SYSTEM,CLEANABLE, IMPINGEMENT (HIGH VELOCITY TYPE)This specification is approved for use within the Naval Sea Systems Command,Department of the Navy, and is available for use by all Departments andAgencies of the Department of Defense.1. SCOPE1.1 Scope. This specification co

4、vers air filters of permanent andcleanable types. They are for use in filtering dust and lint from the airpassing through ventilating, heating and cooling systems.1.2 Classification. Air filters are of the following classes asspecified (see 6.2).Classes:Class 1 - Air filtersClass 2 - Air filters non

5、magnetic2. APPLICABLE DOCUMENTS2.1 General. The documents listed in this section are specified insections 3 and 4 of this specification. This section does not includedocuments cited in other sections of this specification or recommended foradditional information or as examples. While every effort ha

6、s been made toensure the completeness of this list, document users are cautioned that theymust meet all specified requirements documents cited in sections 3 and 4 ofthis specification, whether or not they are listed.Provided by IHSNot for ResaleNo reproduction or networking permitted without license

7、 from IHS-,-,-MIL-PRF-16552F22.2 Government documents.2.2.1 Specifications, standards, and handbooks. The following standardsand publications form a part of this document to the extent specified herein.Unless otherwise specified, the issues of these documents are those listed inthe issue of the Depa

8、rtment of Defense Index of Specifications and Standards(DODISS) and supplement thereto, cited in the solicitation (see 6.2).STANDARDSDEPARTMENT OF DEFENSEMIL-STD-2142 Magnetic Silencing Characteristics, Measurement of(Unless otherwise indicated, copies of the above specifications, standards,and hand

9、books are available from the Standardization Documents Order Desk, 700Robbins Avenue, Building. 4D, Philadelphia, PA 19111-5094.)2.2.2 Other government documents, drawings, and publications. Thefollowing other Government documents, drawings, and publications form a partof this document to the extent

10、 specified herein. Unless otherwise specified,the issues are those cited in the solicitation.PUBLICATIONSNAVSEA TECHNICAL PUBLICATIONS9074-AR-GIB-010/278 Requirements for Fabrication, Welding andInspection, Casting Inspection and Repairfor Machinery, Piping and Pressure Vessels(Unless otherwise indi

11、cated, copies of the above publication are availablefrom the Standardization Documents Order Desk, 700 Robbins Avenue, Building4D, Philadelphia, PA 19111-5094.)2.3 Non-government publications. The following document(s) form a partof this document to the extent specified herein. Unless otherwise spec

12、ified,the issues of the documents which are DOD adopted are those listed in theissue of the DODISS cited in the solicitation. Unless otherwise specified,the issues of documents not listed in the DODISS are the issues of thedocuments cited in the solicitation (see 6.2).AMERICAN SOCIETY FOR TESTING AN

13、D MATERIALS (ASTM)ASTM-E-662 Test method for specific optical density of smokegenerated by solid materialsASTM-E-800 Guide for measurement of gases present or generatedduring fires.ASTM-F-1166 Standard Practice for Human Engineering Design forMarine Systems, Equipment and Facilities(Application for

14、copies should be addressed to the American Society forTesting and Materials 1916 Race Street. Philadelphia, PA 19103)THE AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR CONDITIONINGENGINEERS, INC. (ASHRAE)52.1-1992 Gravimetric and Dust Spot Procedures for Testing Air-Cleaning Devices Used in Gene

15、ral Ventilation for RemovingParticulate MatterProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-16552F3(Application for copies should be addressed to the American Society ofHeating, Refrigerating and Air Conditioning Engineers, Inc., Publicatio

16、nSales, 1791 Tullie Circle, NE, Atlanta, GA 30329)AMERICAN WELDING SOCIETY (AWS)B2.1-84 Welding Procedure and (2) include special requirements of the contract ororder prior to distribution of final drawings.6.5 Identifying numbers. A national stock number (NSN) and acomponent identification number (

17、CID No.) will be assigned by the Governmentafter drawing approval. The contractor is responsible to: (1) identify thesenumbers in shipping papers; and (2) mark these numbers on each filteridentification plates.6.6 Technical manuals. The requirement for technical manuals shouldbe considered when this

18、 specification is applied on a contract. If technicalmanuals are required, military specifications and standards that have beencleared and listed in DoD 5010.12-L, Acquisition Management Systems and DataRequirements Control List (AMSDL) must be listed on a separate Contract DataRequirements List (DD

19、 Form 1423), which in included as an exhibit to thecontract. The technical manuals must be acquired under separate contract lineitem in the contract.6.7 Definitions.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-16552F96.7.1 Air filter. The

20、air filter consists of a filtering mediaenclosed in a frame or binding channel, media retaining guards, and handles.6.7.2 Face area. The face area of a filter is the area, in squarefeet, obtained by multiplying the inside dimensions of the face of the filterframe or binding channel.6.7.3 Face veloci

21、ty. The face velocity of a stream of air passingthrough a filter, expressed in feet per minute, is the rate of flow of airmeasured in cubic feet per minute divided by the face area of the filter.6.7.4 Dust load. Dust holding capacity is the amount of synthetic dustfed to the test filter times its av

22、erage arrestance when the test filterreaches the rated final resistance.6.7.5 Arrestance. Arrestance is an efficiency value. A standardizeddust consisting of various particle sizes is fed into an air cleaner and theweight fraction of dust removed is determined. Under ASHRAE 52.1-1992, thistype of ef

23、ficiency measurement is named synthetic dust weight arrestance todistinguish it from other efficiency values.6.7.6 Resistance (to air flow). Resistance is the static pressure dropacross the filter at a given air flow rate. The term “pressure drop” is usedinterchangeably with resistance.6.8 Recommend

24、ed practices. The following documents provideinformation for the design, manufacture, testing, and qualification ofvaneaxial fans used for cooling of gas turbine machinery previously suppliedto the United States Navy, and may be used for guidance:a. MIL-F-16552 Filters, Air Environmental Control Sys

25、tem, Cleanable,Impingement (High Velocity Type)b. NAVSHIPS Drawing 804-1170895 Filters, Air, Navy Standardc. MIL-STD-889 Dissimilar Metals6.9 Subject term (key word) listing.Air filtersAir filters, nonmagnetic6.10 Changes from previous issue. Marginal notations are not used inthis revision to identi

26、fy changes with respect to the previous issue due tothe extensiveness of the changes.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-16552F101/8”All tolerances are +/- 1/16 inch except as noted.FIGURE 1. Sizes and physical interface dimension

27、s of air filters.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-16552F11Custodian: Preparing ActivityNavy - SH Navy - SH(Project 4130-N001)Review activities:DLA - ISProvided by IHSNot for ResaleNo reproduction or networking permitted without

28、 license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both thedocument number and revision letter should be given.2. The submitter of this form must complete blocks 4,5,6, and 7 and send to preparinga

29、ctivity.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not be used to request copies of documents, nor to request waivers,or clarification of requirements on current contracts. Comments submitted on this formdo not constitute or imply autho

30、rization to waive any portion of the referenceddocument(s) or to amend contractual requirements.I RECOMMEND A CHANGE:1. DOCUMENT NUMBERMIL-PRF-16552F2. DOCUMENT DATE (YYYYMMDD)01 June 20013. DOCUMENT TITLE FILTERS, AIR ENVIRONMENTAL CONTROL SYSTEM, CLEANABLE, IMPINGMENT(HIGH VELOCITY TYPE)4. NATURE

31、OF CHANGE (Identify paragraph number and include proposed rewrite, ifpossible. Attach extra sheets as needed)5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (IncludeArea Code)(1) Commercial(2) DSN7. DATESUBMITTED

32、(YYYYMMDD)8. PREPARING ACTIVITYa. NAMERuth Butlerb. TELEPHONE (Include Area Code)(1) Commercial (2) DSN(202) 781-3726 326-3726c. ADDRESS (Include Zip Code)Commander, Naval Sea Systems CommandATTN: SEA 03Q, 1333 Isaac Hull Ave, SE,Washington Navy Yard, Washington DC 20376IF YOU DO NOT RECEIVE A REPLY WITHIN 45DAYS, CONTACT:Defense Standardization Program Office(DLSC-LM)8725 John J Kingman Road Suite 2533DD Form 1426, FEB 1999 (EG) PREVIOUS EDITION IS OBSOLETE WHS/DIDR, Feb Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-