NAVY MIL-S-29130 A-1978 SHORTS MEN-S POLYESTER COTTON《男式涤棉短裤》.pdf

1、MIL-S-29L30A 84 7997906 038773b Y M MIL-S-29130A 26 Julv 1978 SUPERSEDING MIL-S-29130 (SA) 21 May 1974 MILITARY SPECIFICATION SHORTS, MENS, POLYESTER/COTTON This specification is approved for use by Naval Supply Systems Command, Department of the Navy and is available for use by all Departments and

2、Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. cotton cloth. This specification covers shorts made from a polyester and * 1.2 Classification. The shorts shall be one type of two classes, in the following sizes (see 6.2): . Class 1 - Khaki Class 2 - White Schedule of sizes Short 26, 28, 3

3、0, 32, 34, 36, 38, 40, 42 Regular 26, 28, 30, 32, 34, 36, 38, 40, 42, 44 Long 28, 30, 32, 34, 36, 38, 40, 42, 44 2. APPLICABLE DOCUMENTS * 2.1 Issues of documents. Th? following documents of the issue in effect on date of invitation or bids qr request for-proposal, form a part of this specification

4、to the extent specified herein: Beneficial comments (recommendations, additions, deletions). and any pertinent data which may be of use in improving this document should be addressed to: Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA., 01760) by using the self-addressed

5、Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 8405 c Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-2L30A Lt b O387737 b MIL-S-2913OA SPECIFICATIONS TEDERAL V-B-781 - Butto

6、n, Sewing Hole and Button, Staple (Plastic) V-F-106 - Fasteners, Slide, Interlocking V-T-276 - Thread, Cotton V-T-280 - Thread, Cotton Gimp, Buttonhole CCC-C-438 - Cloth, Buckram, Cotton DDD- L- 2 O - Label; For Clothing, Equipage and Tentage (General Use) MILITARY MIL-C-326 - Cloth, Silesia, Cotton

7、 MIL-B-17757 - Boxes, Shipping, Fiberboard (Modular Sizes) MIL-C-29127 - Cloth, Twill, Polyester and Cotton, Crease Resistant MIL-T-43548 - Thread, Polyester, Cotton-Covered MIL-C-43718 - Cloth, Twill, Polyester, Polyester and Cotton; Finish Polyester and Rayon STANDARDS FEDERAL FED-STD-751 - Stitch

8、es, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-1488 - Provisions for Evaluating Quality of Trousers At tribu tes (Copies of specifications, standards, drawings and publications required by contr

9、actors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) * LAWS AND REGULATIONS U. S. POSTAL, SERVICE MANLiAL (Copies of manual may be obtained from the Superintendent of Documents, U. S. Government Printing O

10、ffice, Washington, D. C. 20402). 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise indicated, the issues in effect on date of invitation for bids or request for proposal shall apply: 2 -7 /I- - Provided by IHSNot for Re

11、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-27L30A 84 7979706 0387738 8 - - MIL-S-2 9 130A NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Application for copies should be addressed to the American Trucking Association

12、s, Inc., Traffic Department, 1616 P Street, N.W., Washington, D. C. 20036.) UNIFORM CLASSIFICATION COMNITTEE, AGENT Uniform Freight Classification (Application for copies shall be addressed to .the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606.) 3. R

13、EQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample, in which case this specification shall govern. * 3.2 First article. When specified (see 6.2), the contractor shall

14、furnish sample unit(s) for first article inspection and approval (see 4.3). 3.3 Material. 3.3.1 Basic material. 3.3.1.1 Class 1 shorts. The basic material for class 1 shorts shall be polyester/cotton, crease-resistant finish cloth, Khaki 2101 conforming to Class 1 of MIL-C-29127. 3.3.1.2 Class 2 sho

15、rts. The basic material for class 2 shorts shall be polyester/cotton, crease-resistant finish cloth, White 3006 conforming to Class 2 of MIL-C-29127. * 3.3.2 Pocketing. cloth, unbleached, for class 1 and class 3 shorts and bleached white for class 2 shorts, conforming to type III of MIL-C-326. As an

16、 alternate, a twill cloth conforming to class 1 of BIIL-C-43718 may be used. The material for pocketing shall be cotton silesia * 3.3.3. Lining. The material for waistband lining, right fly lining and left fly interlining shall be cotton silesia cloth, unbleached for class 1 shorts and bleached whit

17、e for class 2 shorts, conforming to type I of MIL-C-326. As an alternate, a twill cloth conforming to class 1 of MIL-C-43718 may be used. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29130A 3.3.4 Buckram. The material for interlining the w

18、aistband shall be cotton buckram cloth, natural in color for class 1 shorts and bleached white for class 2 shorts, conforming to type II, class 1 of CCC-C-438. 3.3.5 Thread and gimp. 3.3.5.1 Thread, polyester, cotton-covered. The thread for seaming and stitching the shorts shall be a polyester cotto

19、n-covered thread conforming to MIL-T-43548 in the following sizes may be used: - Us e Ticket No. piy Seaming and tacking 40, 50 Overedging 70 Button sewing 20 2 or 3 2 2 or 3 3.3.5.2 w. The cotton gimp for buttonhole shall conform to NO. 8, type I or II of V-T-280. 3.3.5.3 Color of thread and gimp.

20、Khaki, P-1, Cable No. 66019 for class 1 shorts and shall be bleached white for class 2 shorts. The thread and gimp shall be dyed 3.3.5.3.1 Colorfastness. * 3.3.5.3.1.1 Colorfastness of thread. to laundering, chlorine bleaching and light, equal to or better than the standard sample. When no standard

21、sample is available, the dyed thread shall show “good“ fastness to laundering, chlorine bleaching, and light when tested as specified in V-T-276 or MIL-T-43548. The dyed thread shall show fastness 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Pro

22、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29L30A 8L( m 779970b 0387743 m MIL-S-29130A 3.4 Design. The short shall have two side quarter top pockets, two hip pockets, a separate waistband, back darts and hemmed leg bottoms. * 3.4.1 Figures. W

23、hen inconsistencies exist between the specification and the figures, the written specification shall govern. * 3.5 Patterns. be furnished by the Government (see 6.3). The patterns allow a 114 to 318 inch (0.6 to 1.Ocm) seam allowance for all seams, except hip pocket seams, joining of flies to right

24、and left fronts, where 114 inch (0.6cm) allowance is provided, inseams and outseams where 112 inch (1.3cm) allowance is pro- vided and seat seam where 718 inch (2.2cm) outlet is provided. The working patterns shall be identical to the Government patterns. Government patterns nor the working patterns

25、 shall be altered in any way. The figures are furnished for information purposes only. Standard patterns to be used to cut working patterns will Neither the 3.5.1 List of pattern parts, The components of the shorts shall be cut from materials as specified in accordance with the pattern parts indicat

26、ed: Material Pattern Nomenclature Cut Parts Basic material Front 2 Back 2 Side pocket bearer 2 Side pocket facing 2 Hip pocket cord 2 Hip pocket bearer 2 Flies (1 right and 1 left) 2 Waistband (right and left) 2 Cotton silesia cloth Left fly interlining Side pockets Hip pockets or twill cloth Right

27、fly lining 3.6 Construction. 3.6.1 Stitches, seams, and stitchings. Stitch, seam, and stitching types, Where as specified in Table I shall conform to FED-STD-751. or stitch types are given for the same operation, any one may be used. stitch type 401 is used, the looper (underthread) shall be on the

28、inside of the shorts. When two or more seam 3.6.2 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in Table I. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.6.3 Thread breaks and ends of seams. Ends o

29、f all seams and stitching produced with 301 stitch type, when not caught in other seams or stitching shall be backtacked not less than 114 inch (0.6cm). Thread breaks (all stitch types) shall be secured by stitching back of the break not less than 1/2 inch (1.3cm). may be repaired using 301 stitch t

30、ype. stitching shall overlap not less than 1/2 inch (1.3cm). * 3.6.4 Buttonholes. cut, and correctly positioned. with the purling on the outside. taper bar type, with ends tacked, and worked over gimp. The cut length shall be 5/8 to 3/4 inch (1.6 to 1.9cm). The bar end of buttonhole shall have a min

31、imum of 4 stitches not counting the first cross-over in that it is part of the buttonhole not the bar. top of buttonhole should be pulled through to the underside. Skipped stitches or thread breaks (401 stitch type) Ends of a continuous line of The buttonholes specified in Table I shall be clean The

32、 stitching shall be caught in the fabric Buttonholes shall be of the eyelet end, Ends of gimp finishing on 3.7 Manufacturing operations requirements. The shorts shall be manu- factured in accordance with operation requirements specified in Table I. The supplier is not required to follow the exact se

33、quence of operations. * 3.7.1 Shade and size marking. The component parts of the shorts shall be marked to insure a uniform shade and size throughout the garment. Any method may be used except: (a) Corrosive metal fastening devices (b) Sew-on type tickets (c) Adhesive type tickets which show discolo

34、ration and the adhesive mass adheres to the material upon removal of the tickets. * 3.7.2 Pressing. with a heated pressing iron or machine. All pressing required in Table I shall be performed 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L-S-29 O

35、A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n a U G O V rn u r rn w O c W B 8 i: % g 3 u I H 3 i“ 1 I aJ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29130A n a ci G O u 10 ci L W c, 2

36、i B % 2 % 8 w O rl u I H al f-l m I O ln m I O rn mhl II O0 rnb O m mmm I III O o00 O ul Lnmm e rl I O rl e .j. rl d I I O O rl rl O rl I cl rl I c Ei! I (d 6 Ei! rl I (d 3 D O e d m O O m rl rlrlrl O00 4m.j. rl arl om OS rlm 1 ci u* um. .rl al al ci Ma v) a *rl alm au Ga 1 (dalo u .rl rl murl am (d

37、 oc ow m do I u s 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 rl I % i51 MIL-S-29130A WNN m I O III O00 rnbb mo O . - mmN m I O III O00 mmb mo O V e No3 cdco rlo rlN UN I IFiFiI 01 Odal (de da rlN aPN Irl rlrl CAh CAW AA rlrlNm I-lFi a O000

38、o(d Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RIL-S-27130A 84 06 0387753 4 W MIL-S-29130A n a u G O U c W 0 u Fi O % W p . B o I O In m I O u) mm mm II InIn mul O0 II O0 m I O u) VI I O u) 4. 4. rl rl I I O O d rl rl I s 4. d I O rl rl m m i d

39、md 44. O M I O m mm II O0 mm rid o NO rl om rH alo ci al orl ao c ad do +J1 WP al dal c alci s %al “L; a MZ Gdo (d .d sal 5 25 24 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-27L30A 9 W 7777906 03877b0 I W qe F4 rl 4-4-4. l-lrlrl 4- d N d 3

40、d r) m La m 4- m N m O m Co N La N 4 n )u) rl N N rl co W n m al N .rl m rl rl KJ W n 4. N 4- cr) m “0 W n m al N .rl m 4 I-t KJ W n m i- hf W rl rl n m al N .rl m rl rl KJ W I SI 2 z! ro H F: $4 KJ rl 1 M 2 MIL-S-29130A al 5 al rl P 1 O a a F: (d a al $4 a, (0 ci $4 w 2 g 5 .rl B al M a al a al a r

41、l O w O ci al M a a, a al a rl O w $4 w a s i? m .rl w O $4. ala gal UKJ u Ma rlci 5 .a 0” dg ZE! sz $4$4 11 rom da dl 8 s ap rl w O a, M a al E! ci u O P O ci r-i 2 E! E i? A al m JJ O $4 U $4 w a KJ NI 25 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

42、-,-,-MIL-S-27L30A 4 7779706 0387761 3 MIL-S-29130A * 3.9 Workmanship. grade of product established by this specification. As a final step in the suppliers product control plan before formation of a lot, each dress pair of shorts shall be examined after pressing and prior to folding for packaging, an

43、d a pair of shorts containing a selected defect shall not be included in the end item lot. Selected defects are those defects listed in MIL-STD-1488 indicated by an asterisk (*). the applicable acceptable point value of defect limit. The finished shorts shall conform to the quality and The occurrenc

44、e of defects shall not exceed 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all in - spection requirements as specified herein. in the contract, the contractor may use his own or any

45、 other facilities suitable for the performance of the inspection requirements specified herein unless disapproved by the Government. perform any of the inspections set forth in this specification where such inspections are deemed necessary to assure supplies and services conform to the prescribed re

46、quirements. Except as otherwise specified The Government reserves the right to 4.1.1 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. J; 4.2 Classification of inspecti

47、on. The inspection requirements specified herein are classified as follows: 1. 2. First article inspection (see 4.3). Quality conformance inspection (see 4.4). 4.3 First article inspection. When required, the first article submitted in accordance with 3.2 shall be inspected for compliance with desig

48、n, con- struction, workmanship, appearance, and dimensional requirements. 4.4 Quality conformance inspection. Inspection shall be performed in accordance with MIL-STD-1488. The shorts shall be classified as dress (“D“) for the purpose of inspection. 4.4.1 Component and material inspection. In accordance with 4.1 above, components and materials shall be inspected and tested in accordance with the requirements o referenced specifications, drawings, and standards unless otherwise amended, excluded, modified or qualified in this specification or applic