ONORM B 3737-1988 Plate glass for building and construction attack-resistant glazing Systems shot resisting glazing requirements and tests marking of conformity《建筑物和建造用平板玻璃 抗攻击玻璃系统.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

JUS M A1 340-1983 Workshop gauges and references gauges for lain parts Limit values of deviations and admissible wear for interna! measuras《莱恩（lain）部件车间计量器及参照计量器 内部测量的限制阀偏差及容许磨损》.pdf

JUS M A1 411-1978 Tolerances in mechanical engineering Tolerances for sizes without tolerance indication Permissible deviation ofform and position《机械工程公差 无公差指示的尺寸公差 形式及位置容许的公差范围》.pdf

JUS M A1 435-1994 Tolerances in mechanical engineering - Tolerances for sizes without tolerance indication - Deviations for sizes of sizes of wrought copper and copper alloys forgi.pdf

JUS M A1 436-1997 General tolerances - Tolerances for linear and angular dimension drop forgings of wrought aluminium and aluminium alloys《通用公差 落锤锻造锻铝与铝合金线性与角度尺寸的公差》.pdf

JUS M A5 010-1991 ame Series of coalcal tapers and taper angles《园锥体 圆锥锥尖系列及锥角》.pdf

JUS M A5 011-1991 Coae System of cone tolerances for conical workpieces from C = 1 3 to 1 500 and lengtbs from 6 to 630 mm《圆锥体 C=1：3至1：500且长度范围从6至630毫米的锥形工件的圆锥公差系统》.pdf

JUS M A5 012-1991 Cone System of cone fits for cones from C = 1 3 to 1 500 lenghts from 6 to 630mm and diameters up to 500 mm《圆锥体 圆锥体配合系统 C = 1：3到 1：500，产度 6 到 630毫米 口径到 500 毫米》.pdf

JUS M A5 013-1991 Cone Methods for testing of internat and external cones《圆锥体 内外椎体测试方法》.pdf

JUS M A5 014-1991 Cone Vocabulary《圆锥体 词汇》.pdf