ONORM ISO 4759 Teil 3-1982 Tolerances of washers for metric bolts screws and nuts with thread diameters jrom ≥ 1 up to ≤ 150 mm Product grades A and C《螺纹直径≥1 mm 至≤150 mm 螺栓、螺钉和螺母的公.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN ISO 2267-2016 Surface active agents - Evaluation of certain effects of laundering - Methods of preparation and use of unsoiled cotton control cloth (ISO 2267 1986)《表面活性剂 某些洗涤效果.pdf

DIN ISO 2271-1982 Surface active agents detergents determination of anionic-active matter (direct two-phase titration procedure)《表面活性剂 洗涤剂 用直接双相滴定法测定阴离子活性物质》.pdf

DIN ISO 22743-2015 Water quality - Determination of sulfates - Method by continuous flow analysis (CFA) (ISO 22743 2006 + Cor 1 2007)《水质 硫酸盐测定 连续流量分析法(CFA)(ISO 22743-2006+Cor 1-200.pdf

DIN ISO 22826-2008 Destructive tests on welds in metallic materials - Hardness testing of narrow joints welded by laser and electron beam (Vickers and Knoop hardness tests) (ISO 22.pdf

DIN ISO 2285-2013 Rubber vulcanized or thermoplastic - Determination of tension set under constant elongation and of tension set elongation and creep under constant tensile load (I.pdf

DIN ISO 22915-1-2013 Industrial trucks - Verification of stability - Part 1 General (ISO 22915-1 2008)《工业车辆 稳定性验证 第1部分 总则(ISO 22915-1-2008)》.pdf

DIN ISO 22915-16-2017 Industrial trucks - Verification of stability - Part 16 Pedestrian-propelled trucks (ISO 22915-16 2014)《工业用卡车 稳定性验证 第16部分 脚踏卡车(ISO 22915-16-2014)》.pdf

DIN ISO 22915-2-2015 Industrial trucks - Verification of stability - Part 2 Counterbalanced trucks with mast (ISO 22915-2 2008)《工业卡车 稳定性验证 第2部分 带桅杆的平衡力卡车(ISO 22915-2-2008)》.pdf

DIN ISO 22915-3-2017 Industrial trucks - Verification of stability - Part 3 Reach and straddle trucks (ISO 22915-3 2014)《工业卡车 稳定性的验证 第3部分 前移式和插腿式卡车(ISO 22915-3-2014)》.pdf