ONORM L 1088-1993 Chemical analysis of soils - Determination of plant-available phosphate and potassium by calcium-lactate-hydrochloric acid-method (DL-method)《土壤化学分析 钙乳酸盐盐酸法（ DL一法.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

KS M ISO 11644-2007 Leather－Test for adhesion of finish《皮革 涂层的附着试验》.pdf

KS M ISO 11673-2005 Unplasticized polyvinylchloride(PVC－U) pressure pipes－Determination of the fracture toughness properties《未增塑聚氯乙烯(PVC-U)压力管 断裂韧性测定》.pdf

KS M ISO 11759-2009 Rubber hoses and hose assemblies for dispensing liquefied petroleum gases(LPGs)－Specification《液化石油气用橡胶软管和软管组件(LPG) 规范》.pdf

KS M ISO 11795-2007 Agricultural tractor drive wheel tyres－Method of measuring tyre rolling circumference《农业拖拉机用驱动轮胎 测量轮胎滚动圆周的方法》.pdf

KS M ISO 11833-2-2012 Plastics－Unplasticized poly(vinyl chloride) sheets－Types dimensions and characteristics－Part 2：Sheets of thickness less than 1 mm《塑料 PVC U未增塑聚氯乙烯薄板 类型、尺寸和特征 第.pdf

KS M ISO 11907-1-2009 Plastics－Smoke generation－Determination of the corrosivity of fire effluents－Part 1：Guidance《塑料 烟雾产生 灭火废液腐蚀性的测定 第1部分 导则》.pdf

KS M ISO 11909-2012 Binders for paints and varnishes－Polyisocyanate resins－ General methods of test《涂料和清漆用粘接剂 聚异氰酸树脂 一般检验法》.pdf

KS M ISO 11922-1-2003 Thermoplastics pipes for the conveyance of fluids－Dimensions and tolerances－Part 1：Metric series《流体传输用热塑管 尺寸和公差 第1部分 米制系列》.pdf

KS M ISO 11997-1-2011 Paints and varnishes－Determination of resistance to cyclic corrosion conditions－Part 1：Wet(salt fog) dry humidity《涂料和清漆 耐周期性腐蚀的测定 第1部分 湿(盐雾) 干燥 湿度影响试验》.pdf