ONORM M 1341-2-1995 Control of measuring and test equipment Testtng Instruction for vemier callipers for depht measurement《测量控制及测试设备 用于深度测量的游标卡尺测试说明》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

JUS M B0 511-1981 Metne screw thread with tnangular li U-protile bauges tor internat tnreaas loierances ror znreaa gauges《公称螺纹 三角 ISO属性 内部螺纹计量器 螺纹计量器公差》.pdf

JUS M B0 512-1981 Metric screw thread with triangular ISOprofile Gauges Gauging of workpices und use of gauges《带有三角形的ISO 轮廓的公制螺纹 工件的测量和量规的使用》.pdf

JUS M B0 514-1981 ISO Metric trapezoidal screw threads Gauges for external and internat screw threads Tolerances far thread gauges《ISO公制梯形螺纹 外部和内部螺纹用量规 螺纹规的公差》.pdf

JUS M B0 520-1983 Cap gauges and ring gaugas GO and NOT GO for major diamater of extemal screw threads for M1 6-6g to inchiding Mf00-6g《外部螺纹大直径过端及不过端口径规和环规M16-6g 到 Mf00-6g（包括Mf00-6.pdf

JUS M B0 540-1983 Plug gauges GO and NOT GO forminordiameterofinternalscrawthraads forM1fi-€Htoinclu~ ding M 100-6H《内部螺纹小直径过端及不过端塞规 M1fi-€H 到 M 100-6H（包括M 100-6H）》.pdf

JUS M B0 600-1985 Taps for ISO metric threads Tolerances on the threadedportion《ISO公制螺纹用水龙头 螺纹部分的公差》.pdf

JUS M B1 003-1987 Metric threads Drill diameters for use to tapping screvvs《公制螺纹 用于锥形螺纹的钻头直径》.pdf

JUS M B1 005-1979 External metric threads with triangular ISO-proflle Runoutsand undercuts《带三角形ISO 剖面的公制外螺纹 收尾和间距》.pdf

JUS M B1 006-1979 Internat metric threads with triangular ISO-profile Runouts and undercuts《带三角形ISO-剖面的国际公制内螺纹 收尾和间距》.pdf