ONORM S 1390 Teil 3-1983 Rjmfjre cartridge and Chamber caliber 5 mm Rem Mag 《缘发式子弹弹药筒和药室 口径5毫米Rem Mag 》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

GOST 24248-1980 Square throw-away (indexable) carbide cutting inserts with cylindrical holes and chip-breaking flutes on both faces Design and dimensions《可转位的多面带孔和双面有碎屑器槽硬质合金切削刀片 结.pdf

GOST 24249-1980 Rhombic throw-away (indexable) carbide cutting inserts with 80 included angle with cylindrical holes and chip-breaking flutes on both faces Desing and dimensions《可转.pdf

GOST 24250-1980 Triangular throw-away (indexable) carbide cutting inserts with end-clearance angle and chip-breaking flutes Design and dimensions《可转位的多面带后角和碎屑器槽的三菱形硬质合金切削刀片 结构及尺寸》.pdf

GOST 24251-1980 Triangular throw-away (indexable) carbide cutting inserts with 20 end-clearance angle Design and dimensions《可转位的多面后角20硬质合金三菱切削刀片 结构及尺寸》.pdf

GOST 24252-1980 Square throw-away (indexable) carbide cutting inserts with end-clearance angle and chip-breaking flutes Design and dimensions《可转位的带后角和切屑槽的多面硬质合金方形切削刀片 结构及尺寸》.pdf

GOST 24253-1980 Square throw-away (indexable) carbide cutting inserts with 20 end-clearance angle Design and dimensions《可转位的后面20角的多面硬质合金矩形切削刀片 结构及尺寸》.pdf

GOST 24254-1980 Rhombic throw-away (indexable) carbide shims with 55 included angle Design and dimensions《可转位的菱形55角的多面硬质合金支承刀片 结构及尺寸》.pdf

GOST 24255-1980 Rhombic throw-away (indexable) carbide cutting inserts with 55 included angle and cylindrical holes Design and dimensions《可转位的菱形55带孔角的多面硬质合金切削刀片 结构及尺寸》.pdf

GOST 24256-1980 Rhombic throw-away (indexable) carbide cutting inserts with 55 included angle with cylindrical holes and chip-breaking flutes on one face only Design and dimensions.pdf