1、 Standards For Plastics Piping TR 5 105 Decker Court, Suite 825, Irving, TX 75063 Phone: 469-499-1044 Fax: 469-499-1063 www.plasticpipe.org 2 September 2009 STANDARDS FOR PLASTICS PIPING Foreword This technical report has been prepared to provide producers, users, engineers, code officials, installe
2、rs and others interested in plastics piping with an up-to-date list of standards covering high quality plastic piping components. Standards for the purpose of this report include component specifications, methods of test and recommended practices for pipe, tubes, conduits, fittings and related produ
3、cts made of plastics. Although the Plastics Pipe Institute is concerned only with thermoplastics, standards for thermoset plastics are also included. The only piping products and regulations listed in this publication are those of national standing. State, regional and local plumbing and other pipin
4、g codesmany of which are adoptions in total, or in part, of national model codesare not covered. It should be noted that most of these product standards (specifications) include product quality control requirement values that usually cannot be used for engineering design criteria. Such criteria are
5、covered in recommended practices, codes, model codes, installation procedures, separate reports and the appendices of some of these product standards. Those standards that contain information on engineering design criteria and/or the closely related installation procedures are herein identified. Bef
6、ore selecting the type of plastic and the related standards for an application, the design criteria, limitations, and installation techniques must be considered to achieve satisfactory service. Also, any applicable codes must be considered. Information on these aspects may be obtained from the perti
7、nent codes; the standards listed herein, the publications or staff of the Plastics Pipe Institute and of other organizations (identified in this report), or from the manufacturers of plastic pipe components and plastic materials. As the plastics industry has grown, other trade organizations have bee
8、n formed. Their scopes are listed at the end of this report to enable you to direct you inquiries to the appropriate organization. The Plastics Pipe Institute, Inc., as a service to the industry has prepared this report. The information in this report is offered in good faith and believed to be accu
9、rate at the time of its preparation, but is offered without any warranty, express or implied. PPI does not endorse the proprietary products or processes of any manufacturer and assumes no responsibility for compliance with applicable laws and regulations. This Technical Report is a living document a
10、nd is updated on a regular basis. If standards need to be added, please forward the standard title to PPI. “This Technical Report was first issued in December 1979. This revision was prepared in September 2009.” 3 September 2009 STANDARDS FOR PLASTICS PIPING Introduction This publication contains li
11、stings of standards for various types of plastics piping as promulgated by numerous standards-making organizations, such as the American Society for Testing and Materials (ASTM), the American Association of State Highway and Transportation Officials (AASHTO), various U.S. Government agencies and so
12、on. For the convenience of the reader, this publication has been arranged into three sections. Section I and II are devoted to ASTM standards, which are published in Volume 08.04 of the Annual Book of ASTM Standards. Section I categorizes the ASTM standards into one of eight listings: Plastic Pipe S
13、pecifications Plastic Fittings Specifications Plastic Pipe Joints and Joining Materials Systems Specifications (both pipe and fittings) Methods of Test Recommended Practices Terminology Plastic Pipe and Fittings Materials Section II categorizes the ASTM Standards into listings such as: Piping by Typ
14、e of Material (PE, PVC, etc.) Piping Systems by Type of Application (DWV, gas, sewer, water, etc.) Pipe Installation and Components (fittings, joints, seals, solvent cement and primers, underground installation General Test Methods Section III contains listings of standards promulgated by organizati
15、ons other than ASTM (with their addresses) as well as sources of further information. American Association of State Highway and Transportation Officials (AASHTO) American National Standards Institute (ANSI) American Petroleum Institute (API) American Society of Agricultural Engineers (ASAE) American
16、 Water Works Association (AWWA) Canadian Government Standards Board (CGSB) Canadian Standards Association (CSA) U.S. Department of Agriculture Natural Resources Conservation Service (NRCS) U.S. Department of Transportation 4 September 2009 U.S. Department of Housing & Urban Development (HUD) Interna
17、tional Association of Plumbing & Mechanical Officials (IAPMO) International Standards Organization (ISO) National Electrical Manufacturers Association (NEMA) National Fire Protection Association (NFPA) NSF International Underwriters Laboratories (UL) UniBell PVC Pipe Association (UniBell) Internatio
18、nal Code Council (ICC) National Association of Plumbing-Heating-Cooling Contractors (PHCC) Plastic Pipe and Fittings Association (PPFA) The Vinyl Institute (VI) 5 September 2009 SECTION I ASTM American Society for Testing and Materials 100 Barr Harbor Drive West Conshohocken, PA 19428 (610) 832-9500
19、 Internet: www.astm.org Plastic Pipe Specifications D1527 Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80 D1785 Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedule 40, 80, and 120 D2104 Polyethylene (PE) Plastic Pipe, Schedule 40 D2239 Polyethylene (PE) Plastic Pipe (SIDR-PR)
20、Based on Controlled Inside Diameter D2241 Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) D2282 Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR) D2310 Machine-Made “Fiberglass” (Glass-fiber-reinforced Thermosetting-resin) Pipe D2447 Polyethylene (PE) Plastic Pipe, Schedules 4
21、0 and 80 Based on Outside Diameter D2466 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 D2513 Thermoplastic Gas Pressure Pipe, Tubing and Fittings D2737 Polyethylene (PE) Plastic Tubing D2996 Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-
22、Resin) Pipe D2997 Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe D3035 Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter D3262 “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe D3517 “Fiberglass” (Glass-Fiber-Reinforced
23、Thermosetting-Resin) Pressure Pipe F187 Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation F405 Corrugated Polyethylene (PE) Pipe and Fittings F441 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 F442 Chlorinated
24、 Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR) F714 Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter F810 Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields 6 September 2009 F876 Crosslinked Polyethylene (PEX) Tubing F89
25、1 Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core F894 Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe F949 Poly (Vinyl Chloride) (PVC) Corrugated Sewer Pipe with a Smooth Interior and Fittings F1281 Crosslinked Polyethylene/Aluminum/Crosslinked Polyethyle
26、ne (PEX-AL-PEX) Pressure Pipe F1282 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe F1335 Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service F1483 Oriented Poly (Vinyl) Chloride PVCO, Pressure Pipe F1488 Coextruded Composite Pipe F1499 Coextruded Compos
27、ite Drain, Waste and Vent Pipe (DWV) F1533 Specification for Deformed Polyethylene (PE) Liner F2160 Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) F2262 Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Tubin
28、g OD Controlled SDR9 Plastic Fittings Specifications D2464 Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings Schedule 80 D2466 Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 D2467 Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 D2609 Plastic Insert Fittings fo
29、r Polyethylene (PE) Plastic Pipe D2683 Socket-Type Polyethylene (PE) Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing D3261 Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing D3311 Drain, Waste and Vent (DWV) Plastic Fittings Patter
30、ns D3840 Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Non-Pressure Applications D5685 Standard Specification for “Fiberglass“ (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings F409 Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittin
31、gs F437 Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 F438 Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 F439 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 F1055 Electrofusion Type Polyethy
32、lene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing F1336 Poly (Vinyl Chloride) (PVC) Gasketed Sewer Fittings 7 September 2009 F1380 Metal Insert Fittings for Polybutylene (PB) Tubing F1733 Butt Heat Fusion Polyamide (PA) Plastic Fittings for Polyamide (PA) Plastic Pipe and Tu
33、bing F1807 Standard Specification for Metal Insert Fittings utilizing a Copper Crimp Ring for SDR9 Cross-Linked Polyethylene (PEX) Tubing F1924 Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing F1970 Specification for S
34、pecial Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems F1974 Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite
35、 Pressure Pipe F2080 Specification for Cold-Expansion Fittings With Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe F2135 Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings F2159 Specification for Plastic Insert Fittings Utilizing a Copper Crimp R
36、ing for SDR9 Cross-linked Polyethylene (PEX) Tubing F2434 Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing F2735 Specification for Plastic In
37、sert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing Plastic Pipe Joints and Joining Materials D2235 Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings D2564 Solvent Cements for Poly (Vinyl Chloride) (PVC) Plasti
38、c Piping Systems D3138 Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Non-Pressure Piping Components D3139 Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals D3212 Joints for Drain and Sewer Plastic Pipes Using Flex
39、ible Elastomeric Seals D4161 “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals D2672 Joints for IPS PVC Pipe Using Solvent Cement D3122 Solvent Cement for Styrene-Rubber (SR) Plastic Pipe and Fittings F477 Elastomeric Seals (Gaskets) for Joining P
40、lastic Pipe F493 Solvent Cement for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings F656 Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings 8 September 2009 F913 Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe F1056
41、Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings Systems Specifications (Both Pipe and Fittings) D2513 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings D2517 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pi
42、pe and Fittings D2661 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings D2665 Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste and Vent Pipe and Fittings D2680 Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride)
43、(PVC) Composite Sewer Piping D2729 Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings D2751 Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings D2846 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems D2852 Standard Specification for Styrene-Rubber (
44、SR) Plastic Drain Pipe and Fittings D2949 3.25-In. Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings D3034 Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings D3754 “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pre
45、ssure Pipe F194 Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing F480 Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 F512 Specificat
46、ion for Smooth-Wall Poly Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation F667 Standard Specification for Large Diameter Corrugated Polyethylene Pipe and Fittings F679 Poly (Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings F714 Polyethylene (PE) Pla
47、stic Pipe (SDR-PR) Based on Outside Diameter F771 Polyethylene (PE) Thermoplastic High-Pressure Irrigation Pipeline Systems F794 Standard Specification for Poly (Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter F877 Crosslinked Polyethylene (PEX) Plas
48、tic Hot- and Cold-Water Distribution Systems F1412 Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems 9 September 2009 F1498 Taper Pipe Threads 60 for Thermoplastic Pipe and Fittings F1865 Specification for Mechanical Cold Expansion Insert Fitting With Compression Sleeve for Cross-lin
49、ked Polyethylene (PEX) Tubing F1866 Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings F1960 Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing F1986 Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems F2164 Practice for Field Leak Testing of Polyethylene (PE) Pressure Piping Systems Using Hydrostatic Pressure F2206 Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE) Pl
