REG NASA-LLIS-0006-1991 Lessons Learned - Orbiter Exterior Panel Separation During Flight due to Incorrect Installation (Washers not Provided Under Fasteners).pdf

上传人:周芸 文档编号:1017660 上传时间:2019-03-21 格式:PDF 页数:2 大小:12.95KB
下载 相关 举报
REG NASA-LLIS-0006-1991 Lessons Learned - Orbiter Exterior Panel Separation During Flight due to Incorrect Installation (Washers not Provided Under Fasteners).pdf_第1页
第1页 / 共2页
REG NASA-LLIS-0006-1991 Lessons Learned - Orbiter Exterior Panel Separation During Flight due to Incorrect Installation (Washers not Provided Under Fasteners).pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Lessons Learned Entry: 0006Lesson Info:a71 Lesson Number: 0006a71 Lesson Date: 1991-04-29a71 Submitting Organization: JSCa71 Submitted by: L. UnderwoodSubject: Orbiter Exterior Panel Separation During Flight due to Incorrect Installation (Washers not Provided Under Fasteners) Description of Driving

2、Event: Following the shuttle mission STS-27, the right side orbital maneuvering system (OMS) pod carrier panel on the orbiter OV-104 was missing. It was concluded that the panel was installed incorrectly. Six flat washers were not installed under the mounting fasteners. This caused damage to the bas

3、e panel material upon installation. The panel became loose during flight, produced a gap, and was pulled off by the air flow. No additional damage was sustained by the orbiter thermal protection system or other orbiter components. The panel installation procedures did not clearly identify the requir

4、ement for the washers. The procedures were revised to include the steps for installing the washers. Approximately 100 orbiter panels of similar configuration were recommended for inspection to assure this anomaly was not present elsewhere within the orbiter fleet.Lesson(s) Learned: Incomplete assemb

5、ly or installation instructions (no reference to the use of washers) can result a in poorly fastened exterior mounted component (orbiter OMS carrier panel) causing loss of the component and potentially hazardous debris.Recommendation(s): Procedures were changed to include detailed instructions for i

6、nstalling washers. All similar orbiter panels were inspected to preclude recurrence of the anomaly.Evidence of Recurrence Control Effectiveness: N/AProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Documents Related to Lesson: N/AMission Directorate(s)

7、: a71 Exploration Systemsa71 Sciencea71 Space Operationsa71 Aeronautics ResearchAdditional Key Phrase(s): a71 Configuration Managementa71 Flight Operationsa71 Flight Equipmenta71 HardwareAdditional Info: Approval Info: a71 Approval Date: 1993-09-09a71 Approval Name: Ron Montaguea71 Approval Organization: JSC/NS3a71 Approval Phone Number: 281-483-8576Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • JUS K D4 003-1982 Files and rasps Cut classification《锉刀和粗锉刀 锉口分类》.pdf JUS K D4 003-1982 Files and rasps Cut classification《锉刀和粗锉刀 锉口分类》.pdf
  • JUS K D4 010-1982 Files and rasps Technical reguirements《锉刀和粗锉刀 技术要求》.pdf JUS K D4 010-1982 Files and rasps Technical reguirements《锉刀和粗锉刀 技术要求》.pdf
  • JUS K D4 900-1982 Files Shanks《直柄锉刀》.pdf JUS K D4 900-1982 Files Shanks《直柄锉刀》.pdf
  • JUS K F0 001-1989 Grain si7 es of fused alumlnium oxlde and sIlicon carbide for bonded abrasive products esignaticm and graJn slze distribution《粘结磨具用熔解氧化铝和金刚砂颗粒的粒度 粒度分布标示》.pdf JUS K F0 001-1989 Grain si7 es of fused alumlnium oxlde and sIlicon carbide for bonded abrasive products esignaticm and graJn slze distribution《粘结磨具用熔解氧化铝和金刚砂颗粒的粒度 粒度分布标示》.pdf
  • JUS K F0 002-1989 GraJns of fused aluminium oxide and silicon carbide for boodod abrasivc products Grain si e analysis of macrogrits F 4 to F 220《粘结磨具用熔解氧化铝和金刚砂颗粒 F4- F220 微粒的粒度分析》.pdf JUS K F0 002-1989 GraJns of fused aluminium oxide and silicon carbide for boodod abrasivc products Grain si e analysis of macrogrits F 4 to F 220《粘结磨具用熔解氧化铝和金刚砂颗粒 F4- F220 微粒的粒度分析》.pdf
  • JUS K F0 003-1989 Grains of fuse a luminJuri oxide and silicon carbide for abrasive products Descrlptlon of tbe sleving macbines《磨具用熔解氧化铝和金刚砂颗粒 筛分设备描述》.pdf JUS K F0 003-1989 Grains of fuse a luminJuri oxide and silicon carbide for abrasive products Descrlptlon of tbe sleving macbines《磨具用熔解氧化铝和金刚砂颗粒 筛分设备描述》.pdf
  • JUS K F0 004-1989 Gralns of fused alumlnium oxide and slllccm carbide for bonded abrasive products Grala si e analysis of microgrits P 230 to F 1200《粘结磨具用熔解氧化铝和金刚砂颗粒 P 230-F 1200微粒.pdf JUS K F0 004-1989 Gralns of fused alumlnium oxide and slllccm carbide for bonded abrasive products Grala si e analysis of microgrits P 230 to F 1200《粘结磨具用熔解氧化铝和金刚砂颗粒 P 230-F 1200微粒.pdf
  • JUS K F0 005-1989 Gralns of fused alumiuium oxide and silicon carbide for boodod abrasivc products Particle si e measurement of microgrfts by Eppendorf - photosedimentometer《粘结磨具产品.pdf JUS K F0 005-1989 Gralns of fused alumiuium oxide and silicon carbide for boodod abrasivc products Particle si e measurement of microgrfts by Eppendorf - photosedimentometer《粘结磨具产品.pdf
  • JUS K F0 006-1988 Grains of fused alumininm oxfdo and silJcon carbide for abrasivo products DeterminatIon of the buJk densfty of tbe abraslve grains《模具产品用熔解氧化铝和金刚砂颗粒 磨粒的散装密度的测定》.pdf JUS K F0 006-1988 Grains of fused alumininm oxfdo and silJcon carbide for abrasivo products DeterminatIon of the buJk densfty of tbe abraslve grains《模具产品用熔解氧化铝和金刚砂颗粒 磨粒的散装密度的测定》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1