REG NASA-LLIS-0257-1994 Lessons Learned - JP-4 Fuel Leak.pdf

上传人:amazingpat195 文档编号:1017908 上传时间:2019-03-21 格式:PDF 页数:2 大小:13.07KB
下载 相关 举报
REG NASA-LLIS-0257-1994 Lessons Learned - JP-4 Fuel Leak.pdf_第1页
第1页 / 共2页
REG NASA-LLIS-0257-1994 Lessons Learned - JP-4 Fuel Leak.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Lessons Learned Entry: 0257Lesson Info:a71 Lesson Number: 0257a71 Lesson Date: 1994-01-20a71 Submitting Organization: LERCa71 Submitted by: S. PapellSubject: JP-4 Fuel Leak Description of Driving Event: Operations personnel, in an engine test facility, reported that JP-4 fuel was found leaking in th

2、e basement of the building. Emergency staff responding to the call discovered that the fuel had originated from the engine on the main floor and had leaked onto a power panel in the basement. The spill was located on and around a 480VAC motor control center that contained breakers and contactors to

3、power the pumps, blowers, and fans in the building.The building was evacuated due to a potential explosion hazard. The power was turned off and power to the control center terminated. Absorbent pads were placed around the fuel spill for containment and the area barricaded to prevent access.It was de

4、termined that the fuel spill originated from an open fuel return low point drain valve, recently added to the facility, that was not put on the facility drawings. Operations personnel performing a walk-through inspection of the facility did not observe the added drain and therefore were not aware of

5、 the presence and open valve position of the drain.Lesson(s) Learned: 1. Modifications made to plumbing systems of fuel tanks that are inadvertently left off the facility drawings can lead to unsafe engine operation.2. Fuel system low-point drains should not be placed in close proximity to, or above

6、 critical operating systems.Recommendation(s): 1. Correct facility drawings when modifications are made and notify line management Provided by IHSNot for Resale-,-,-responsible for the facility.2. Design facilities so that fuel drain lines and valves are not in a position to dump fuel on operating

7、electrical equipment.Evidence of Recurrence Control Effectiveness: N/ADocuments Related to Lesson: N/AMission Directorate(s): N/AAdditional Key Phrase(s): a71 Configuration Managementa71 Energetic Materials - Explosive/Propellant/Pyrotechnica71 Facilitiesa71 Hazardous/Toxic Waste/MaterialsAdditional Info: Approval Info: a71 Approval Date: 1994-06-15a71 Approval Name: Maria Havenhilla71 Approval Organization: LERC/EBASa71 Approval Phone Number: 216-977-1483Provided by IHSNot for Resale-,-,-

展开阅读全文
相关资源
猜你喜欢
  • ASTM E2092-2004 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis《热机分析三点弯曲处变形温度的标准试验方法》.pdf ASTM E2092-2004 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis《热机分析三点弯曲处变形温度的标准试验方法》.pdf
  • ASTM E2092-2013 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis《采用热机械分析对三点弯曲上变形温度的的标准试验》.pdf ASTM E2092-2013 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis《采用热机械分析对三点弯曲上变形温度的的标准试验》.pdf
  • ASTM E2092-2018 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis.pdf ASTM E2092-2018 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis.pdf
  • ASTM E2093-2005 Standard Guide for Optimizing Controlling and Reporting Test Method Uncertainties from Multiple Workstations in the Same Laboratory Organization《来自同一实验室机构中多个工作站的试验方.pdf ASTM E2093-2005 Standard Guide for Optimizing Controlling and Reporting Test Method Uncertainties from Multiple Workstations in the Same Laboratory Organization《来自同一实验室机构中多个工作站的试验方.pdf
  • ASTM E2093-2012 Standard Guide for Optimizing Controlling and Assessing Test Method Uncertainties from Multiple Workstations in the Same Laboratory Organization 《优化 控制和评估同一实验室组织中多工.pdf ASTM E2093-2012 Standard Guide for Optimizing Controlling and Assessing Test Method Uncertainties from Multiple Workstations in the Same Laboratory Organization 《优化 控制和评估同一实验室组织中多工.pdf
  • ASTM E2093-2012(2016) Standard Guide for Optimizing Controlling and Assessing Test Method Uncertainties from Multiple Workstations in the Same Laboratory Organization 《来自同一实验室机构中多个.pdf ASTM E2093-2012(2016) Standard Guide for Optimizing Controlling and Assessing Test Method Uncertainties from Multiple Workstations in the Same Laboratory Organization 《来自同一实验室机构中多个.pdf
  • ASTM E2096 E2096M-2010 Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing《利用远场试验现场检测铁磁性热交换管的标准操作规程》.pdf ASTM E2096 E2096M-2010 Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing《利用远场试验现场检测铁磁性热交换管的标准操作规程》.pdf
  • ASTM E2096 E2096M-2016 Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing《利用远程现场试验现场检验铁磁换热器管的标准实施规程》.pdf ASTM E2096 E2096M-2016 Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing《利用远程现场试验现场检验铁磁换热器管的标准实施规程》.pdf
  • ASTM E2096-2005 Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing《远程现场试验法现场检验铁磁热交换器管道的标准规程》.pdf ASTM E2096-2005 Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing《远程现场试验法现场检验铁磁热交换器管道的标准规程》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1