1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS3793/3C AEROSPACE MATERIAL SPECIFICATION AMS3793/3 REV. C Issued 1986-04 Stabilized 2013-09
5、Revised 2017-08 Superseding AMS3793/3B Tape and Webbing, Textile, Para-Aramid Intermediate Modulus 3/4 Inch (19 mm), 0.11 to 0.60 Ounces per Yard (3.4 to 18.6 g/m) RATIONALE The purpose of this revision is to correct a typo in Table 1: Class 1, 2, and 3 should be Class 1, 4, and 5 to match Table 2 a
6、nd MIL-T-87130 Type IV. 1. SCOPE 1.1 Form This specification covers three classes of para-aramid tape and webbing of a single width and with varying weights. 1.2 Application See AMS 3793. 1.3 Classification Width of 3/4 inch 1/16 (19 mm 1.6) and weight classes as shown in Table 1. Table 1 - Weight o
7、f products Class Weight Maximum oz/yd (g/m) 1 4 5 0.11 (3.4) 0.50 (15.5) 0.60 (18.6) SAE INTERNATIONAL AMS3793/3C Page 2 of 3 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. Th
8、e supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE Int
9、ernational, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS3793 TAPE AND WEBBING, TEXTILE, PARA-ARAMID Intermediate Modulus 3. TECHNICAL REQUIREMENTS 3.1 Basic Specification The complete requirements for
10、procuring the tape and webbing described herein shall consist of this document and the latest issue of the basic specification, AMS3793. 3.2 Properties Tape and webbing shall conform to the requirements of Table 2 and the following: 3.2.1 Width: Shall be 3/4 inch 1/16 (19 mm 1.6). 3.2.2 Weight: Shal
11、l be as specified in 1.3 for the class ordered. 4. QUALITY ASSURANCE PROVISIONS See AMS3793. 5. PREPARATION FOR DELIVERY See AMS3793. 6. ACKNOWLEDGMENT See AMS3793. 7. REJECTIONS See AMS3793. SAE INTERNATIONAL AMS3793/3C Page 3 of 3 8. NOTES See AMS3793. Table 2 - Properties Class Breaking Strength
12、minimum pounds Breaking Strength minimum N Warp Denier Warp Ply Warp Total Ends, minimum Fill Denier Fill Ply Fill Picks per inch (25.4 mm) Weave 1 4 5 500 3000 4500 2225 13345 20015 200 1500 1500 1 2 2 90 31 41 200 1500 1500 1 1 1 38 12 11 Plain Plain Plain 8.1 Revision Indicator A change bar (l) l
13、ocated in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY AMS COMMITTEE “P”
