1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2009 SAE International All rights reserved. No part of this publication ma
3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US
4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4182GAEROSPACEMATERIALSPECIFICATIONAMS4182 REV. G Issued 1948-09 Reaffirmed 2006-10 Revised
5、2009-12 Superseding AMS4182F Aluminum Alloy, Wire 5.0Mg - 0.12Mn - 0.12Cr (5056-0) Annealed(Composition similar to UNS A95056) RATIONALEAMS4182G revises tolerances (3.5) and is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers an aluminum alloy in the f
6、orm of wire. 1.2 Application This wire has been used typically for the manufacture of screen for reinforcement of, and to provide electrical conductivity through, rubber gaskets, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on
7、the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified
8、, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2355 Quality Assurance, Sampling and Testing, Alu
9、minum Alloys and Magnesium Alloy, Wrought Products, Except Forging Stock, and Rolled, Forged, or Flash Welded Rings Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4182G Page 2 of 42.2 ASTM Pu
10、blications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM B 660 Packaging/Packing of Aluminum and Magnesium Products 2.3 ANSI Publications Available from American National Standards Institute, 25 West 43
11、rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org. ANSI H35.2 Dimensional Tolerances for Aluminum Mill Products ANSI H35.2M Dimensional Tolerances for Aluminum Mill Products (Metric) 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table
12、 1, determined in accordance with AMS2355. TABLE 1 - COMPOSITION Element min max SiliconIronCopperManganeseMagnesiumChromiumZincOther Elements, each Other Elements, total Aluminum-0.054.50.05-remainder0.300.400.100.205.60.200.100.050.153.2 Condition Annealed.3.3 Properties Wire shall conform to the
13、following requirements; tensile properties shall be determined in accordance with AMS2355 on the mill produced size. 3.3.1 Tensile Properties Shall be shown in Table 2. TABLE 2 - TENSILE PROPERTIES Property Value Tensile Strength, max Elongation in 2 Inches (50.8 mm) or 4D, min Nominal Diameter 0.12
14、5 to 0.375 inch, excl (3.18 to 9.52 mm, excl) 46.0 ksi (317 MPa) 20%Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4182G Page 3 of 43.3.2 Bending Wire shall withstand, without cracking, bendi
15、ng at room temperature flat on itself. 3.4 Quality Wire, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the wire. 3.5 Tolerances Shall conform to all applicable requirements of ANSI H35.2 or A
16、NSI H35.2M . 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of wire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed neces
17、sary to ensure that the wire conforms to specified requirements. 4.2 Classification of Tests All technical requirements are acceptance tests and shall be performed on each lot. 4.3 Sampling and Testing Shall be in accordance with AMS2355. 4.4 Reports The vendor of wire shall furnish with each shipme
18、nt a report stating that the wire conforms to the composition and tolerances, and showing the numerical results of tests on each inspection lot to determine conformance to the other acceptance tests requirements. This report shall include the purchase order number, inspection lot number, AMS4182G, s
19、ize, and quantity. The report shall also identify the producer, the product form, and the size of the mill product. 4.5 Resampling and Retesting Shall be in accordance with AMS2355. 5. PREPARATION FOR DELIVERY 5.1 Packaging and Identification Wire shall be identified as follows: 5.1.1 Wire, supplied
20、 on spools, shall contain 5, 10, 15, or 30 pounds (2.27, 4.54, 6.80, or 13.6 kg), as ordered. Each spool shall be legibly marked, on one flange of the spool or on a durable tag attached to each spool, with not less than the nominal size, alloy number and temper, lot number, AMS4182G, and manufacture
21、rs identification. 5.1.2 Straight wire shall be bundled, boxed, or secured on lifts and identified by two durable tags legibly marked with the information of 5.1.1 and attached, not farther than 2 feet (610 mm) from each end, to the wire in each bundle, box, or lift. 5.1.3 Coiled wire shall be ident
22、ified with the information of 5.1.1, legibly marked on a durable tag attached to each coil or directly on one flange of each spool. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4182G Page 4
23、 of 45.1.4 Wire shall be prepared for shipment in accordance with ASTM B 660 and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the wire to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall mention this spe
24、cification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (l) located in the left margin is for the
25、convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not
26、 used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 When wire is supplied for use in screen, designers may find it necessary to specify that wire in one direction may be in a condition other than annealed.8.4 Dimen
27、sions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.5 Purchase documents should specify not les
28、s than the following: AMS4182GSize of wire desired Length of cut lengths or weight of spools desired Quantity of wire desired. 8.6 Similar Specifications QQA430, Alloy 5056, Temper O, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PREPARED BY AMS COMMITTEE “D“ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
