1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4510H AEROSPACE MATERIAL SPECIFICATION AMS4510 REV. H Issued 1939-12 Reaffirme
5、d 2009-06 Revised 2015-07 Superseding AMS4510G Phosphor Bronze, Sheet, Strip, and Plate 94.5Cu - 4.0Sn - 0.19P Spring Temper (H08) (Composition similar to C51000) RATIONALE AMS4510H revises the method of analysis for Composition (3.1), and is a Five Year Review and update of this specification. 1. S
6、COPE 1.1 Form This specification covers a copper alloy (phosphor bronze) in the form of sheet, strip, and plate. 1.2 Application These products have been used typically for stampings and springs, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following docume
7、nts in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been canceled and no superseding document ha
8、s been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2222 Tolerances, Copper and C
9、opper Alloy Sheet, Strip, and Plate 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM B248 General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
10、 SAE INTERNATIONAL AMS4510H Page 2 of 4 ASTM B248M General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) ASTM E8/E8M Tension Testing of Metallic Materials ASTM E18 Rockwell Hardness Hardness of Metallic Materials ASTM E478 Chemical Analysis of Copper A
11、lloys 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1, determined by ASTM E478, or by other analytical methods acceptable to purchaser. Table 1 - Composition Element (3.1.1) min max Tin Phosphorus Zinc Iron Lead Copper Sum of Named Elements 4.2 0
12、.03 - - - - 99.5 5.8 0.35 0.30 0.10 0.05 (See 3.1.2) 3.1.1 These composition limits do not preclude the presence of other elements. Limits may be established and analysis required for unnamed elements by agreement between the manufacturer or supplier and purchaser. 3.1.2 Copper may be reported as “r
13、emainder”, or as the difference between the sum of results for all analyzed elements and 100%, or as the result of direct analysis. 3.1.3 When all named elements in Table 1 are analyzed, the sum shall be minimum, but such determination is not required for routine acceptance of each lot. 3.2 Conditio
14、n Cold rolled, spring (H08) temper (See 8.2). 3.3 Properties The product shall conform to the following requirements. 3.3.1 Tensile Properties Shall be 91 to 105 ksi (627 to 724 MPa), determined in accordance with ASTM E8/E8M. 3.3.2 Hardness Shall be as shown in Table 2, or equivalent hardness (See
15、8.3), determined in accordance with ASTM E18. Table 2 - Hardness Nominal Thickness Inch Nominal Thickness Millimeters Hardness Over 0.003 to 0.029, incl Over 0.029 to 0.039, incl Over 0.039 Over 0.08 to 0.74 Over 0.74 to 0.99 Over 0.99 76 to 80 HR30T 92 to 97 HRB 94 to 98 HRB SAE INTERNATIONAL AMS45
16、10H Page 3 of 4 3.4 Quality The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product. 3.5 Tolerances Shall conform to AMS2222 as applicable to refractory alloys. 4. QUALITY ASSU
17、RANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that t
18、he product conforms to the specified requirements. 4.2 Classification of Tests All technical requirements are acceptance tests and shall be performed on each lot. 4.3 Sampling and Testing Shall be in accordance with ASTM B248 or ASTM B248M. 4.4 Reports The vendor of the product shall furnish with ea
19、ch shipment a report showing the results of tests for chemical composition, tensile properties, and hardness of each lot. This report shall include the purchase order number, lot number, AMS4510H, size, and quantity. 4.5 Resampling and Retesting If any specimen used in the above tests fails to meet
20、the specified requirements, disposition of the product may be based on the results of testing three additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for rejection of the product represented. Results of all
21、 tests shall be reported. 5. PREPARATION FOR DELIVERY 5.1 Identification The product shall be identified as in 5.1.1 unless line marking as in 5.1.2 is specified by purchaser. 5.1.1 Each sheet, strip, and plate shall be legibly marked near one end, coils being marked near the outside end, with AMS45
22、10H, manufacturers identification, and nominal thickness, using any suitable marking fluid. As an alternate method, individual pieces or bundles shall have attached a durable tag marked with the above information or shall be boxed and the box marked with the same information. 5.1.2 When specified by
23、 purchaser, each sheet, strip, and plate shall be legibly marked on one face, in the respective location indicated below, with AMS4510H, lot number, manufacturers identification, and nominal thickness. The characters shall be applied using a suitable marking fluid removable in hot alkaline cleaning
24、solution without rubbing. The markings shall have no deleterious effect on the product or its performance and shall be sufficiently stable to withstand normal handling. The specification number, manufacturers identification, and nominal thickness shall be continuously line marked; the lot number may
25、 be included in the line marking or may be marked at one location on each piece. SAE INTERNATIONAL AMS4510H Page 4 of 4 5.1.2.1 Flat Strip, 6 Inches (152 mm) and Under in Width Shall be marked in one or more lengthwise rows of characters recurring at intervals not greater than 3 feet (914 mm). 5.1.2
26、.2 Flat Sheet, Flat Strip Over 6 Inches (152 mm) in Width, and Plate Shall be marked in lengthwise rows of characters recurring at intervals not greater than 3 feet (914 mm), the rows being spaced not more than 6 inches (152 mm) apart and alternately staggered. 5.1.2.3 Coiled Sheet and Strip Shall b
27、e marked near both the outside and inside ends of the coil; the markings shall be applied as in 5.1.2 or shall appear on a durable tag or label attached to the coil and marked with the information of 5.1.2. When the product is wound on cores, the tag or label may be attached to the core. 5.2 Packagi
28、ng The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall menti
29、on this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (l) located in the left marg
30、in is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars a
31、nd (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Copper temper designations are defined in ASTM B601. 8.3 Hardness conversion tables for metals are presented in ASTM E140. 8.4 Terms used in AMS are clarified in ARP1917. 8.5 Dimensions and proper
32、ties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.6 Purchase documents should specify not less than the following: AMS4510H Form and size of product desired Quantity of product desired. 8.7 ASTM B103, Alloy C51000, Spring Temper, is listed for information only and shall not be construed as acceptable alternates unless all requirements of this AMS are met. PREPARED BY AMS COMMITTEE “D“
