1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro
2、m, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.Copyright 2006 SAE InternationalAll rights reserved. No part of this publication may be
3、reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: 724-776-4970 (outside USA)Fax: 724-
4、776-0790Email: custsvcsae.orgSAE WEB ADDRESS: http:/www.sae.orgSteel, Bars, Forgings, and Tubing0.31 - 0.38C (SAE 1035) (Composition similar to UNS G10350)1. SCOPE:1.1 Form: This specification covers a carbon steel in the form of bars, forgings, mechanical tubing, and forging stock.1.2 Application:
5、This product has been used typically for parts requiring moderate strength and high ductility, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent spe
6、cified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been canceled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE Publications: Availa
7、ble from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.AMS 2231 Tolerances, Carbon Steel BarsMAM 2231 Tolerances, Metric, Carbon Steel BarsAMS 2253 Tolerances, Carbon and Alloy Steel TubingMAM 2253 Tolerances, Metric, Carbon and Alloy Steel TubingAMS 2259 Chemical Check Analysis Limits, Wro
8、ught Low-Alloy and Carbon SteelsAMS 2370 Quality Assurance Sampling and Testing, Carbon and Low-Alloy Steel Wrought Products and Forging StockAMS 2372 Quality Assurance Sampling and Testing, Carbon and Low-Alloy Steel ForgingsAEROSPACE MATERIAL SPECIFICATIONAMS 5080JIssued JUN 1942Revised OCT 2001Re
9、affirmed FEB 2006Superseding AMS 5080HCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 5080J SAE AMS 5080J- 2 -2.1 (Continued):AMS 2806 Identification, Bars, Wire, Mechanical Tubing, and Extrusion
10、s, Carbon and Alloy Steels and Corrosion and Heat Resistant Steels and AlloysAMS 2808 Identification, Forgings2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.ASTM E 10 Brinell Hardness of Metallic MaterialsASTM E 350 Chemical Analysis of Carbon Ste
11、el, Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and Wrought Iron3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 350, by spectrochemical methods, or by other analytical met
12、hods acceptable to purchaser:3.1.1 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2259.3.2 Condition: The product shall be supplied in the following condition; hardness shall be determined in accordance with ASTM E 10:3.2.1 Bars: Hot finished and annealed, unles
13、s otherwise ordered, having hardness not higher than 229 HB or equivalent. Bars ordered cold finished may have hardness as high as 241 HB or equivalent (See 8.2).3.2.2 Forgings: As ordered.TABLE 1 - CompositionElement min maxCarbon 0.31 0.38Manganese 0.60 0.90Silicon 0.15 0.35Phosphorus - 0.040Sulfu
14、r - 0.050Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 5080J SAE AMS 5080J- 3 -3.2.3 Mechanical Tubing: Cold finished, unless otherwise ordered, having hardness not higher than 241 HB or equiva
15、lent. Tubing ordered hot finished and annealed shall have hardness not higher than 229 HB or equivalent (See 8.2).3.2.4 Forging Stock: As ordered by the forging manufacturer.3.3 Quality: The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign ma
16、terials and from imperfections detrimental to usage of the product.3.3.1 Grain flow of die forgings, except in areas which contain flash-line end grain, shall follow the general contour of the forgings showing no evidence of reentrant grain flow.3.4 Tolerances: Shall be as follows:3.4.1 Bars: In acc
17、ordance with AMS 2231 or MAM 2231.3.4.2 Mechanical Tubing: In accordance with AMS 2253 or MAM 2253.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tes
18、ts. Purchaser reserves the right to sample and perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements.4.2 Classification of Tests: 4.2.1 Acceptance Tests: Composition (3.1), hardness (3.2), and tolerances (3.5), are acceptance tests and shall
19、be performed on each heat or lot as applicable.4.2.2 Periodic Tests: Grain flow of die forgings is a periodic test and shall be performed at a frequency selected by the vendor unless a frequency of testing is specified by purchaser.4.3 Sampling and Testing: Shall be as follows:4.3.1 Bars, Forging St
20、ock, and Mechanical Tubing: In accordance with AMS 2370.4.3.2 Forgings: In accordance with AMS 2372.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 5080J SAE AMS 5080J- 4 -4.4 Reports: The vendor
21、 of the product shall furnish with each shipment a report showing the results of tests for chemical composition of each heat and hardness of each lot, and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers,
22、 AMS 5080J, size, and quantity. If forgings are supplied, the size and melt source of stock used to make the forgings shall also be included.4.5 Resampling and Retesting: Shall be as follows:4.5.1 Bars, Forging Stock, and Mechanical Tubing: In accordance with AMS 2370.4.5.2 Forgings: In accordance w
23、ith AMS 2372.5. PREPARATION FOR DELIVERY: 5.1 Sizes: Except when exact lengths or multiples of exact lengths are ordered, straight bars and tubing will be acceptable in mill lengths of 6 to 20 feet (1.8 to 6.1 m), but not more than 10% of any shipment shall be supplied in lengths shorter than 10 fee
24、t (3 m).5.2 Identification: Shall be as follows:5.2.1 Bars and Mechanical Tubing: In accordance with AMS 2806.5.2.2 Forgings: In accordance with AMS 2808.5.2.3 Forging Stock: As agreed upon by purchaser and vendor.5.3 Protective Treatment: Bars and tubing ordered cold drawn, cold rolled, ground, tur
25、ned, or polished shall be protected from corrosion prior to shipment.5.4 Packaging: The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to en
26、sure carrier acceptance and safe delivery.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 5080J SAE AMS 5080J- 5 -6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revis
27、ion letter in all quotations and when acknowledging purchase orders.7. REJECTION: Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.8. NOTES:8.1 A change bar ( l ) located in the left margin is for the convenience of the user in l
28、ocating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revisions. Change bars and (R) are not used in original
29、publications, nor in specifications that contain editorial changes only.8.2 Hardness conversion tables for metals are presented in ASTM E 140.8.3 Terms used in AMS are clarified in ARP1917, and as follows: 8.3.1 The term “mechanical tubing“ as used in AMS means a heavy-walled cylindrical tubing, int
30、ended primarily for the machining of circular rings, flanges, shafts, etc, having a wall thickness which is a substantial proportion of the outer diameter; such tubing is not normally used for the transmission of fluids and parts made from it are usually machined all over. This product is sometimes
31、known as “hollow bar“.8.4 Purchase documents should specify not less than the following:AMS 5080JForm and size or part number of product desiredQuantity of product desired.PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “E”Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
