1、 Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUM
2、ENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org THIRD ANGLE PROJECTION SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of tec
3、hnicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay
4、 bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AMSDTL22499/2A FEDERAL SUPPLY CLASS 9535REV. AAMS-DTL-22499/2ISSUED 1998-09 REVISED 1999-01 REAF
5、FIRMED 2011-08PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “D, E, F, G, P”AMS SPECIFICATIONSHIM STOCK, LAMINATED, BRASSSHEET 1 OF 3AMS-DTL-22499/2NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-DTL-22499/2A, AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES RE
6、QUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-DTL-22499/2A. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED
7、AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS
8、 WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREME
9、NT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.REV. ACopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS SPECIFICATIONSHIM S
10、TOCK, LAMINATED, BRASSAMS-DTL-22499/2SHEET 2 OF 3REV. ATHE REQUIREMENT FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE ISSUE OF THE FOLLOWING SPECIFICATION SHEET AND THE ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS (DODISS) SPE
11、CIFIED IN THE SOLICITATION: MIL-DTL-22499.- BAR, METAL, FLATREQUIREMENTS1. MATERIAL: BRASS, AS SPECIFIED IN PROCUREMENT DOCUMENT.2. TYPES: I - ALL LAMINATIONSII - ONE-HALF SOLID STOCKCLASSES: 1. - .002 INCH LAMINATIONS2. - .003 INCH LAMINATIONS3. PART NUMBERS: THE PART NUMBER CONSISTS OF M22499/2 TH
12、E BASIC NUMBER OF THIS SPECIFICATIONSHEET AND A DASH NUMBER TAKEN FROM TABLE 1.4. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THEPREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL
13、 TO THE LEFT OF THE DOCUMENT TITLE INDICATESA COMPLETE REVISION OF THE DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS-DTL-22499/2REV. ASHEET 3 OF 3SHIM STOCK, LAMINATED, BRASSAMS SPECIFICATIONTABLE ICopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
