1、AEROSPACE STANDARD FITTING, LUBRICATION, HYDRAULIC, SURFACE CHECK,STRAIGHT THREADS, STEEL, TYPE IIAS15002Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanic
2、al, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-05REVISED 201
3、0-01THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B REV.CFEDERAL SUPPLY CLASS 4730 AS15002SHEET 1 OF 3REV. CPROCUREMENT SPECIFICATION: /5/ AS35411SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis repo
4、rt is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites
5、yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS15002CRATIONALE AS15002 IS BEING REVISED TO ADD ZINC NICKEL FINISH AND QPL/QML NOTE. FIGURE 1 - FITTING, STRAIGHT FIGURE 2 - FITTING, ELBOW INA
6、CTIVE IN PART - SEE NOTE /16/ AEROSPACE STANDARD AS15002SHEET 2 OF 3REV. CFITTING, LUBRICATION, HYDRAULIC, SURFACE CHECK, STRAIGHT THREADS, STEEL, TYPE IITABLE 1 - DIMENSIONS AD WEIGHTS PARTNUMBER FIG. THREAD T PER FED-STD-H28/2 A.031 B/6/CMAX.DMAX.E.003 F5 HLB/100APPROX. REF STEEL AS15002-1 AS15002
7、2 AS15002-3 AS15002-4 1121.250-28 UNF-2A .3125-32 UNEF-2A .250-28 UNF-2A .3125-32 UNEF-2A .125.125.125.125.075.075.075.075.438.500.531.562.750.750.281.312.375.37545 65 .036.031.036.031NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS
8、 IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. MATERIALS: STEEL. SEE PROCUREMENT SPECIFICATION. 2. HEAT TREATMENT: NONE. 3. FINISH: CADMIUM PLATE OR ZINC PLATE. SEE PROCUREMENT SPECIFICATION. a. CODE LETTER C - CADMIUM PLATE b. CODE LETTER P - ZINC PLATE c. CODE LETTER U - ZINC NICKEL PLATE, SEE
9、 PROCUREMENT SPECIFICATION. 4. IDENTIFICATION: MARK PER AS478 METHOD 35D MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, AND PART NUMBER. /5/ PROCUREMENT SPECIFICATION: AS35411 EXCEPT AS SPECIFIED ON THIS STANDARD. THE DRAWING AND ALL THE SPECIFIED DOCUMENTS DEFINE THE REQUIREMENTS FOR THE END PRODUCT.
10、All THE REQUIREMENTS MUST BE MET IN ORDER TO IDENTIFY THE ITEM WITH THAT PART NUMBER. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS./6/ MINIMUM EFFECTIVE THREAD LENGTH. /7/ FITTING END IN ACCORDANCE WITH AS15000, STYLE OPTIONAL. 8. INTENDE
11、D USE: THIS PART IS INTENDED FOR USE IN LUBRICATING CONNECTIONS AT PRESSURES TO 8000 psi. 9. THIS STANDARD IS A CONVERSION OF MILITARY STANDARD MS15002, FITTINGS, LUBRICATION (HYDRAULIC) SURFACE CHECK, STRAIGHT THREADS, STEEL, TYPE II, AND IS NOT A WORD-FOR-WORD CONVERSION. 10. INTERPRETATION OF DRA
12、WING PER ARP4296. 11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. SURFACES OF HEX FLATS MAY BE 250 in Ra. 12. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 13. DIMENSIONING AND TOLERANCING: ASME Y14.5M-
13、1994. 14. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 030. AEROSPACE STANDARD AS15002SHEET 3 OF 3REV. CFITTING, LUBRICATION, HYDRAULIC, SURFACE CHECK, STRAIGHT THREADS, STEEL, TYPE II15. EXAMPLE OF PART NUMBER: AS15002 -1 -P BASIC PART
14、 NUMBER FITTING CONFIGURATION FINISH /16/ PART NUMBERS AS15002-2 AND -4 ARE INACTIVE FOR NEW DESIGN. 17. THIS SPECIFICATION HAS INTERNATIONAL STANDARDIZATION AGREEMENT. SEE AS35411. 18. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL R
15、EVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTA
16、IN EDITORIAL CHANGES ONLY.THE CHANGE BAR ( I ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS STANDARD. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT./19/ INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION.
