1、Copyright 2006 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, orotherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT
2、ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences
3、Theuse ofthis reportisentirelyvoluntary, andits applicabilityand suitabilityfor any particularuse,including any patentinfringement arising therefrom,isthe sole responsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.S
4、AE invites your written comments and suggestions.SHEET 1 OF 3AS18013THIRD ANGLE PROJECTIONAEROSPACE STANDARDAS18013ISSUED 1999-07 REAFFIRMED 2006-11INDICATOR, HUMIDITY, PLUG,COLOR CHANGEPREPARED BY SAE COMMITTEE AGE-2 PROCUREMENT SPECIFICATION: MIL-I-26860FEDERAL SUPPLY CLASS 6685RATIONALETHIS DOCUM
5、ENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY.NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS18013(AS) AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL ST
6、ANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS18013(AS). ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND R
7、EGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNME
8、NT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF
9、THIS SAE TECHNICAL DOCUMENT.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS18013 INDICATOR, HUMIDITY, PLUG,COLOR CHANGEAEROSPACE STANDARDAS18013SHEET 2 OF 3AS18013NOTES:1. INDICATOR PLUGS SHALL BE TYPE II IN ACCORDANCE WITH TH
10、E PROCUREMENT SPECIFICATION.2. MATERIAL:MATERIAL FOR ALL METAL PARTS OF PLUGS MS18013-1 AND MS18013-2 SHALL BE ALUMINUM ALLOY, ANODIZED IN ACCORDANCE WITH SPECIFICATION MIL-A-8625 (SEE TABLE). THE TRANSPARENT INDICATOR COVER SHALL BE BOROSILICATE GLASS CONFORMING TO SPECIFICATION MIL-C-7989, CLASS C
11、MATERIAL FOR PLUG MS18013-3 SHALL BE ZINC PLATED BRASS FOR THE INDICATOR PLUG, THE RETAINER RING, AND THE LOCK NUT. THE GASKET SHALL BE SILICONE RUBBER.3. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .030.4. PLUGS, MS18013-1 AND MS18013-2 SUPERSEDE BUWEPS DWG NO. 1705047.
12、PLUG MS18013-3 SUPERSEDES BUWEPS DWG. NO. 2249378.FOR DESIGN FEATURE PURPOSES, THIS STANDARD TAKES PRECEDENCE OVER PROCUREMENT DOCUMENTS REFERENCED HEREIN.REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.INDICATOR, HUMIDITY, PLUG,COLOR CHANGEAEROSPACE STANDARDAS18013SHEET 3 OF 3AS18013
