1、 AEROSPACE STANDARD CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; IN-SERVICE INSPECTION GAGE FOR AS22520/40 CRIMP TOOLS AS22520/43Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by an
2、y means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.
3、org ISSUED2011-10 REAFFIRMED2016-11 THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5220 AS22520/43 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS22520 SAE Technical Standards BoardRules providethat:“This reportis publishedbySAE toadvancethestateoftechnicaland engineering sciences. The use
4、 of this report isentirely voluntary, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviews eachtechnical reportatleast every fiveyears atwhichtimeitmay berevised,reaffirmed, stabilized,orcancell
5、ed. SAE invites yourwrittencomments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS22520/43 RATIONALE AS22520/43 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREMENTS FOR P
6、ROCURING THE CONTACTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF: SAE AS22520 FIGURE 1 CRIMP TOOL WIRE BARREL INSPECTION GAGE TABLE 1 WIRE BARREL INSPECTION GAGE DESIGN CONFIGURATION AND APPLICATION TOOL PART NO. WIRE RANGE B GO DIM. B NO-GO DIM. TOOL TO BE INSPECTE
7、D M22520/43-01 22-16 0.1090-0.1093 0.1149-0.1150 M22520/40-01 M22520/43-02 16-14 0.1190-0.1193 0.1249-0.1250 AEROSPACE STANDARD AS22520/43 SHEET 2 OF 2 CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; IN-SERVICE INSPECTION GAGE FOR AS22520/40 CRIMP TOOLS FIGURE 2 CRIMP TOOL INSULATION BARREL INSPEC
8、TION GAGE TABLE 2 INSULATION BARREL INSPECTION GAGE DESIGN CONFIGURATION AND APPLICATION TOOLPARTNO. WIRERANGEDGODIM.DNOrGODIM.WMAXTOOLTOBEINSPECTEDM22520/43r03 22r16 0.0300r0.0303 0.1099r0.1100 0.125 M22520/40r01M22520/43r04 16r14 0.0400r0.0403 0.1199r0.1200 0.125REQUIREMENTS: AS SPECIFIED IN AS225
9、20. 1. DIMENSIONS: UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES AS SPECIFIED IN FIGURES AND TABLES. CONFIGURATION IS OPTIONAL WITHIN DEFINED DIMENSIONS. TOLERANCES ARE DECIMALS .005 INCHES AND 5 DEGREES. DIMENSIONS B AND D APPLY AFTER PROTECTIVE COATING (SEE REQUIREMENT 3). 2. MATERIAL: WIRE
10、 BARREL GAGE PINS AND INSULATION BARREL INSPECTION GAGE : ALLOY TOOL STEEL PER ASTM A681, ASTM-A295, OR EQUIVALENT (CLASS OPTIONAL). HARDEN TO ROCKWELL C58-64. WIRE BARREL GAGE HANDLE: ALUMINUM ALLOY, ASTM B211 ALUMINUM AND ALUMINUM-ALLOY BAR, ROD, AND WIRE 3. FINISH: WIRE BARREL GAGE PINS AND INSUL
11、ATION BARREL INSPECTION GAGE; CHROME PLATE WITH ADEQUATE COVERAGE FOR CORROSION AND WEAR RESISTANCE PER AMS-QQ-C-320 PLATING CHROMIUM, CLASS I, TYPE II WITH A THICKNESS OF .00003 INCHES MINIMUM. HANDLE IS ANODIZED. 4. MARKING: UNLESS OTHERWISE SPECIFIED, STAMPING SHALL BE INDENTED OR LASER ETCHED. SUPPLIER NAME SHALL BE COMPLETE OR BE AN AIR1351 LISTED LOGO 5. STORAGE CONTAINER: GAGES SHALL BE FURNISHED WITH A SUITABLE CONTAINER. APPLICATION NOTES: 1. TOOL IS USED AS A GO/NO-GO VERIFICATION INSPECTION GAGE FOR THE AS22520 TOOLS SPECIFIED IN TABLE 1 AND 2.
