1、Copyright 2000 Society of Automotive Engineers, Inc. Printed in the U.S.A.All rights reserved. .TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790 SAE WEB ADDRESS: http:/www.sae.org400 Commonwealth Drive, Warrendale, PA 15096-0001SAE Technical StandardsBoard Rulesprovidethat:“Thisreport i
2、s published by SAEtoadvance thestateoftechnical and engineeringsciences. The useofthis reportisentirelyvoluntary, and its applicabilityand suitability for any particularuse, includingany patent infringement arising therefrom, isthe soleresponsibility of the user.”SAE reviews each technical report at
3、 least every five years at whichtime it maybereaffirmed, revised, or cancelled. SAE invites your writtencomments and suggestions.SHEET 1 OF 4AS22759/3THIRD ANGLE PROJECTIONAEROSPACE STANDARDAS22759/3ISSUED2000-09WIRE, ELECTRIC, FLUOROPOLYMER-INSULATED,TFE-GLASS-TFE, MEDIUM WEIGHT, NICKEL-COATEDCOPPE
4、R CONDUCTOR, 600-VOLTPREPARED BY SAE SUBCOMMITTEE AE-8DFEDERAL SUPPLY CLASS 6145NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-W-22759/3D AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF S
5、AE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-W-22759/3D. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD
6、 (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE
7、 EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE A
8、ND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001WIRE, ELECTRIC, FLUOROPOLYMER-INSULATED,TFE-GLASS-TFE, MED
9、IUM WEIGHT, NICKEL-COATEDCOPPER CONDUCTOR, 600-VOLTAEROSPACE STANDARD AS22759/3SHEET 2 OF 4AS22759/3THE COMPLETE REQUIREMENTS FOR PROCURING THE WIRE DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE ISSUE IN EFFECT OF SPECIFICATION MIL-W-22759.TABLE I. CONSTRUCTION DETAILS.Copyright SAE Intern
10、ational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001WIRE, ELECTRIC, FLUOROPOLYMER-INSULATED,TFE-GLASS-TFE, MEDIUM WEIGHT, NICKEL-COATEDCOPPER CONDUCTOR, 600-VOLTAEROSPACE STAND
11、ARD AS22759/3SHEET 3 OF 4AS22759/3TABLE II. PERFORMANCE DETAILS.ADDITIONAL REQUIREMENTSTEMPERATURE RATING: 260C (500F) max conductor temperatureVOLTAGE RATING: 600 volts (rms) at sea levelSPARK TEST OF PRIMARY INSULATION: Not requiredIMPULSE DIELECTRIC TEST: 8.0 kilovolts (peak), 100% testINSULATION
12、 RESISTANCE: 5000 megohms for 1000 ft (min)WRAP TEST:Mandrel wrap test required; no crackingDielectric test after mandrel wrap, 2500 volts (rms), 60HzBLOCKING: 260 2C (500 3.6F)SHRINKAGE: 0.125 inch max at 260 2C (500 3,6F)WICKING:Sizes 22 through 12 - Procedure II; 2.0% (max) weight increase, 0.250
13、 inch (max) dye travelSizes 10 through 00 - No requirementLOW TEMPERATURE (COLD BEND):Bend temperature: -65 2C (-85 3.6F)Dielectric test, 2500 volts (rms), 60HzTHERMAL SHOCK:Oven temperature, 260 2C (500 3.6F)Max change in measurementSizes 22 through 12: 0.060 inchSizes 10 through 8: 0.100 inchSizes
14、 6 through 00: 0.125 inchCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001WIRE, ELECTRIC, FLUOROPOLYMER-INSULATED,TFE-GLASS-TFE, MEDIUM WEIGHT, NICKEL-CO
15、ATEDCOPPER CONDUCTOR, 600-VOLTAEROSPACE STANDARD AS22759/3SHEET 4 OF 4AS22759/3FLAMMABILITY: Post-flame dielectric test not requiredLIFE CYCLE:Oven temperature 313 2C (595.4 3.6F)Dielectric test, 2500 volts (rms), 60HzDIELECTRIC TEST AFTER IMMERSION: 2500 volts (rms), 60HzABRASION RESISTANCE AFTER I
16、MMERSION: Qualification test onlyHUMIDITY RESISTANCE: 5000 megohms for 1000 ft, min insulation resistance after humidity exposureSURFACE RESISTANCE:Sizes 22 through 12: 500 megohm-inches (min), initial and final readingsSizes 10 through 00: No requirementSMOKE: 313C (595.4F)ACID RESISTANCE:RequiredD
17、ielectric test, 2500 volts (rms), 60HzCOLOR: In accordance with MIL-STD-104, Class 1; white preferred.COLOR STRIPING OR BANDING DURABILITY: 250 cycles (500 strokes) (min), 500 grams weightIDENTIFICATION DURABILITY: 125 cycles (250 strokes) (min), 500 grams weightWIRE LENGTH REQUIREMENTS: Schedule BCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-
