1、AEROSPACE STANDARDINSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE ETHYLENE-TETRAFLUOROETHYLENEFLUOROPOLYMER, SEMI-RIGIDAS23053/14Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mean
2、s, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUE
3、D2016-10THIRD ANGLE PROJECTIONCUSTODIAN: AE-8/AE-8DFEDERAL SUPPLY CLASS5970AS23053/14SUPERSEDES AMS-DTL-23053/14ASHEET 1 OF 3PROCUREMENT SPECIFICATION: AS23053SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The use
4、ofthis reportis entirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom,is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or ca
5、ncelled. SAEinvites your written comments and suggestions.SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS23053/14RATIONALETHIS IS A CONVERSION OF AMS-DTL-23053/14 INTO AN AEROSPACE STANDARD WHICH INCLUDESQUALIFICATION AND REQUIREMENTS FOR A
6、 QUALIFIED PRODUCTS LIST.NOTICETHE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THISDOCUMENT AND THE LATEST ISSUE OF AS23053.REQUIREMENTS1. DIMENSIONS AND PROPERTIES IN INCH/POUND UNITS AND THE FAHRENHEIT TEMPERATURES AREPRIMARY. DIMENSIONS AND PROPERTIES IN SI U
7、NITS AND THE CELSIUS TEMPERATURES ARE SHOWN ASTHE APPROXIMATE EQUIVALENTS OF THE PRIMARY UNITS AND ARE PRESENTED ONLY FOR INFORMATION.2. POLYMER TYPE: THE BASE POLYMER USED IN FORMULATING THIS SLEEVING SHALL BE ETHYLENE-TETRAFLUORETHYLENE FLUOROPOLYMER.3. CONTINUOUS OPERATING TEMPERATURE RANGE: -148
8、 F TO 302 F (-100 TO 150 C).4. COLOR: THE SLEEVING SHALL BE FURNISHED IN CLEAR (TRANSLUCENT WHITE TO TRANSPARENT BLUE), THE AS MANUFACTURED COLOR (SEE 1.3).5. LONGITUDINAL CHANGE: 10%6. PART NUMBER: THE PART NUMBER SHALL BE AS LISTED BELOW:M23053/14 - X XX - XEXAMPLE: 0.500 INCH (12.7 MM) CLEAR AS S
9、UPPLIED ID ETFE SLEEVING SHALL BE IDENTIFIED AS M23053/14-006-C.7. DIMENSIONAL LIFE: THE DIMENSIONAL LIFE OF A PRODUCT APPLIES TO THE EXPANDED I.D., RECOVERED I.D. AND WALL THICKNESS DIMENSIONS OF THE PRODUCT AS SOLD BY THE MANUFACTURER, DISTRIBUTORS AND REBRAND DISTRIBUTORS. AS23053/14 PRODUCTS CAN
10、 BE EXPECTED TO HAVE A MINIMUM DIMENSIONAL LIFE OF 4 YEARS WHEN STORED BETWEEN 32 TO 95 F (0 TO 35 C). PRODUCTS STORED ABOVE THESE CONDITIONS MAY NOT MEET THE MINIMUM EXPANDED I.D. REQUIREMENTS OF THE DETAIL SPECIFICATION. A PRODUCT MAY BE USED BY THE FINAL PURCHASER BEYOND THE EXPECTED MINIMUM DIME
11、NSIONAL LIFE, AS LONG AS THE EXPANDED I.D., RECOVERED I.D. AND WALL THICKNESS OF THE PRODUCT MEET THE REQUIREMENTS OF THIS SPECIFICATION AT THE TIME OF USE.8. UNRESTRICTED SHRINKAGE: TEST METHOD 5.5; 347 F 2 F (175 C 1 C) FOR 10 MINUTES.COLOR CODE DESIGNATOR (SEE 1.3)SIZE IDENTIFIER (SEE TABLE 1)CLA
12、SS (WHERE NO CLASSES ARE SPECIFIED IN THE SPECIFICATION SHEET, THE NUMERIC “0” IS USED)SPECIFICATION SHEETAEROSPACE STANDARDAS23053/14SHEET 2 OF 3INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE ETHYLENE-TETRAFLUOROETHYLENEFLUOROPOLYMER, SEMI-RIGIDTABLE 1 - CONSTRUCTION DETAILS, INCHES (MM) 1/PART NU
13、MBER 3/ AS SUPPLIEDID MINIMUM AFTER UNRESTRICTED SHRINKAGEID MAXIMUM WALL THICKNESS 2/M23053/14-001-C .093 (2.4) .062 (1.6) .010 .002 (0.3 0.1)M23053/14-002-C .125 (3.2) .083 (2.1) .010 .002 (0.3 0.1)M23053/14-003-C .187 (4.7) .125 (3.2) .011 .002 (0.3 0.1)M23053/14-004-C .250 (6.4) .166 (4.2) .013
14、003 (0.3 0.1)M23053/14-005-C .375 (9.5) .250 (6.4) .013 .003 (0.3 0.1)M23053/14-006-C .500 (12.7) .345 (8.8) .013 .003 (0.3 0.1)M23053/14-007-C .750 (19.1) .500 (12.7) .018 .004 (0.5 0.1)M23053/14-008-C 1.000 (25.4) .665 (16.9) .022 .004 (0.6 0.1)M23053/14-009-C 1.250 (31.8) .835 (21.2) .030 .004 (
15、0.8 0.1)M23053/14-010-C 1.500 (38.1) 1.000 (25.4) .030 .004 (0.8 0.1)1/ DIAMETER LIMITS FOR OBJECT TO BE ENCLOSED SHALL BE AS SPECIFIED IN TECHNICAL DATA.2/ WALL THICKNESS VALUES ARE LESS WHEN SHRINKAGE IS RESTRICTED.3/ THE COLOR INIDCATED IS THE STANDARD COLOR. (SEE AS23053 COLOR)TABLE 2 - PHYSICAL
16、 PROPERTIESCHARACTERISTIC REQUIREMENTTEST PROCEDURE AND CONDITIONS(SEE AS23053)AS SUPPLIED:ID MINIMUM TABLE 1 5.3.1RESTRICTED SHRINKAGE NO CRACKS 5.6 347 F 4 F (175 C 2 C)VOLTAGE WITHSTAND PASS 5.6.2.CCLARITY STABILITY PASS 5.16 347 F 2 F (175 C 1 C), 24 HOURSAFTER UNRESTRICTED SHRINKAGE:ID, MAXIMUM
17、 TABLE 1 5.3.2WALL THICKNESS TABLE 1 5.3.3TENSILE STRENGTH, PSI (MPA), MINIMUM6500 (44.8) 5.13 ASTM D638, 20 INCHES/MINUTEULTIMATE ELONGATION, PERCENT, MINIMUM200 5.13 ASTM D638, 20 INCHES/MINUTEDIELECTRIC BREAKDOWN VOLTS, MINIMUM11000 5.2 ASTM D876VOLUME RESISTIVITY, 0HM-CM, MINIMUM1 X 1015 5.2 AST
18、M D876WATER ABSORPTION, PERCENT, MAXIMUM0.1 5.2 ASTM D570, 24 HRS. AT 73 F (23 C)LOW TEMPERATURE FLEXIBILITY NO CRACKING 5.7.1 -85 F 2 F (-65 C 1 C)AEROSPACE STANDARDAS23053/14SHEET 3 OF 3INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE ETHYLENE-TETRAFLUOROETHYLENEFLUOROPOLYMER, SEMI-RIGIDTABLE 2 - P
19、HYSICAL PROPERTIES (CONTINUED)CHARACTERISTIC REQUIREMENTTEST PROCEDURE AND CONDITIONS(SEE AS23053)HEAT RESISTANCE,PROPERTIES AFTER:5.9 392 F 4 F (200 C 2 C) FOR 168 HOURSTENSILE STRENGTH, PSI (MPA), MINIMUM6000 (41.4)ULTIMATE ELONGATION, PERCENT, MINIMUM175DIELECTRIC BREAKDOWN VOLTS, MINIMUM10000SPE
20、CIFIC GRAVITY, MAXIMUM 1.73 5.2 ASTM D792FLAMMABILITY SELF-EXTINGUISHING 15 SECONDS AND 3 INCHES5.14 PROCEDURE A, ASTM D2671APPLICATION NOTES1. INTENDED USE: HEAT SHRINKABLE, SEMI-RIGID, ETHYLENE-TETRAFLUOROETHYLENE FLUOROPOLYMER IS INTENDED FOR USE IN COMPONENT CABLES AND ELECTRONIC LEAD STRAIN REL
21、IEF WHERE LOW EXPANSION RATIOS ARE SATISFACTORY.SPECIFICATION NOTES1. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
