1、AEROSPACE STANDARDINSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, CROSSLINKED, ELASTOMERICPOLYOLEFIN, FLEXIBLEAS23053/16Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect
2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2016-10
3、THIRD ANGLE PROJECTIONCUSTODIAN: AE-8/AE-8DFEDERAL SUPPLY CLASS5970AS23053/16SUPERSEDES AMS-DTL-23053/16ASHEET 1 OF 4PROCUREMENT SPECIFICATION: AS23053SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis r
4、eportis entirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom,is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyearsat whichtime it may berevised, reaffirmed, stabilized, or cancelled.
5、SAEinvites your written comments and suggestions.SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS23053/16RATIONALETHIS IS A CONVERSION OF AMS-DTL-23053/16 INTO AN AEROSPACE STANDARD WHICH INCLUDESQUALIFICATION AND REQUIREMENTS FOR A QUALIFIE
6、D PRODUCTS LIST.NOTICETHE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THISDOCUMENT AND THE LATEST ISSUE OF AS23053.REQUIREMENTS1. DIMENSIONS AND PROPERTIES IN INCH/POUND UNITS AND THE FAHRENHEIT TEMPERATURES ARE PRIMARY.DIMENSIONS AND PROPERTIES IN SI UNITS AND
7、THE CELSIUS TEMPERATURES ARE SHOWN AS THE APPROXIMATE EQUIVALENTS OF THE PRIMARY UNITS AND ARE PRESENTED ONLY FOR INFORMATION.2. POLYMER TYPE: THE BASE ELASTOMER USED IN FORMULATING THIS SLEEVING SHALL BE AN ELASTOMERIC POLYOLEFIN.3. CONTINUOUS OPERATING TEMPERATURE RANGE: -103 F TO +248 F (-75 C TO
8、 +120 C).4. COLOR: THE SLEEVING SHALL BE FURNISHED IN A BLACK COLOR THAT CONFORMS TO CLASS II OF MIL-STD-104 (SEE 1.3).5. LONGITUDINAL CHANGE: 10%6. PART NUMBER: THE PART NUMBER SHALL BE AS LISTED BELOW:M23053/16 - X XX - XEXAMPLE: BLACK, 1.000 INCH (25.4 MM) AS SUPPLIED ID SLEEVING SHALL BE IDENTIF
9、IED AS M23053/16-005-0.7. DIMENSIONAL LIFE: THE DIMENSIONAL LIFE OF A PRODUCT APPLIES TO THE EXPANDED I.D., RECOVERED I.D. AND WALL THICKNESS DIMENSIONS OF THE PRODUCT AS SOLD BY THE MANUFACTURER, DISTRIBUTORS AND REBRAND DISTRIBUTORS. AS23053/16 PRODUCTS CAN BE EXPECTED TO HAVE A MINIMUM DIMENSIONA
10、L LIFE OF 2 YEARS WHEN STORED BETWEEN 32 TO 95 F (0 TO 35 C). PRODUCTS STORED ABOVE THESE CONDITIONS MAY NOT MEET THE MINIMUM EXPANDED I.D. REQUIREMENTS OF THE DETAIL SPECIFICATION. A PRODUCT MAY BE USED BY THE FINAL PURCHASER BEYOND THEEXPECTED MINIMUM DIMENSIONAL LIFE, AS LONG AS THE EXPANDED I.D.
11、, RECOVERED I.D. AND WALL THICKNESS OF THE PRODUCT MEET THE REQUIREMENTS OF THIS SPECIFICATION AT THE TIME OF USE.8. UNRESTRICTED SHRINKAGE PROCEDURES: TEST METHOD 5.5; 347 F 4 F (175 C 2 C) FOR 10 MINUTES.NOTE: THE TERM “POLYOLEFIN” AS USED IN THIS SPECIFICATION INCLUDES COPOLYMERS, BLENDS AND MODI
12、FIED POLYOLEFINSCOLOR CODE DESIGNATOR (SEE 1.3)SIZE IDENTIFIER (SEE TABLE 1)CLASS (WHERE NO CLASSES ARE SPECIFIED IN THESPECIFICATION SHEET, THE NUMERIC “0” IS USED)SPECIFICATION SHEETAEROSPACE STANDARD AS23053/16SHEET 2 OF 4INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, CROSSLINKED, ELASTOMERICPO
13、LYOLEFIN, FLEXIBLETABLE 1 - CONSTRUCTION DETAILS, INCHES (MM) 1/PART NUMBER 3/ ID MINIMUMAFTER UNRESTRICTED SHRINKAGEID MAXIMUMWALL THICKNESS 2/MINIUMUMM23053/16-001-0 .250 (6.4) .125 (3.2) .025 (0.6)M23053/16-002-0 .375 (9.5) .187 (4.7) .030 (0.8)M23053/16-003-0 .500 (12.7) .250 (6.4) .033 (0.8)M23
14、053/16-004-0 .750 (19.1) .375 (9.5) .042 (1.1)M23053/16-005-0 1.000 (25.4) .500 (12.7) .050 (1.3)M23053/16-006-0 1.500 (38.1) .750 (19.1) .070 (1.8)M23053/16-007-0 2.000 (50.8) 1.000 (25.4) .085 (2.2)M23053/16-008-0 3.000 (76.2) 1.500 (38.1) .095 (2.4)M23053/16-009-0 4.000 (101.6) 2.000 (50.8) .110
15、(2.8)1/ DIAMETER LIMITS FOR OBJECTS TO BE ENCLOSED SHALL BE AS RECOMMENDED IN TECHNICAL DATA.2/ THE WALL THICKNESS VALUES ARE LESS WHEN SHRINKAGE IS RESTRICTED.3/ THE COLOR CODE IDENTIFIED IS THE STANDARD ACQUISITION COLOR.TABLE 2 - PHYSICAL PROPERTIES 1/CHARACTERISTIC REQUIREMENTTEST PROCEDURE AND
16、CONDITIONS(SEE AS23053)AS SUPPLIED:ID, MINIMUM TABLE 1 5.3.1LOW TEMPERATURE FLEXIBILITY NO CRACKS 5.7.1 -85 F 4 F (-65 C 2 C)HEAT SHOCK NO CRACKS, FLOWING ORDRIPPING5.8 392 F 4 F (200 C 2 C)RESTRICTED SHRINKAGE NO CRACKS 5.6 302 F 4 F (150 C 2 C)VOLTAGE WITHSTAND PASS 5.6.2.CAFTER UNRESTRICTED SHRIN
17、KAGE:ID, MAXIMUM TABLE 1 5.3.2WALL THICKNESS TABLE 1 5.3.3TENSILE STRENGTH, PSI (MPA), MINIMUM1700 (11.7) 5.13 ASTM D412, 20 INCHES/MINUTEULTIMATE ELONGATION, PERCENT, MINIMUM250 5.13 ASTM D412, 20 INCHES/MINUTETENSILE STRESS AT 100 PERCENTELONGATION, PSI (MPA), MAXIMUM1500 (10.3) 5.12.2 ASTM D412AE
18、ROSPACE STANDARD AS23053/16SHEET 3 OF 4INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, CROSSLINKED, ELASTOMERICPOLYOLEFIN, FLEXIBLETABLE 2 - PHYSICAL PROPERTIES 1/ (CONTINUED)CHARACTERISTIC REQUIREMENTTEST PROCEDURE AND CONDITIONS(SEE AS23053)DIELECTRIC STRENGTH, VOLTS/MIL (KV/MM) MINIMUM300 (11.9)
19、 UP TO AN “AS SUPPLIED ID” OF 0.500200 (7.9) AN “AS SUPPLIED ID” OF 0.500 AND ABOVE5.2 ASTM D2671VOLUME RESISTIVITY, OHM-CM, MINIMUM1 X 109 5.2 ASTM D876SPECIFIC GRAVITY, MAXIMUM 1.5 5.2 ASTM D792CORROSION NO CORROSION OR PITTING 5.10.1 250 F 4 F (121 C 2 C);5.10.2 275 F 4 F (135 C 2 C); FOR 16 HOUR
20、SWATER ABSORPTION, PERCENT, MAXIMUM2.0 5.2 ASTM D570, 24 HOURS AT 73 F (23 C)HEAT RESISTANCE, PROPERTIES AFTER:5.9 302 F 4 F (150 C 2 C), 168 HOURSTENSILE STRENGTH, PSI (MPA), MINIMUM1500 (10.4)ULTIMATE ELONGATION,PERCENT, MINIMUM200FLUID RESISTANCE, PROPERTIES AFTER:5.11TENSILE STRENGTH, PSI (MPA),
21、 MINIMUM1500 (10.3)ULTIMATE ELONGATION,PERCENT, MINIMUM200DIELECTRIC STRENGTH,VOLT/MIL (KV/MM), MINIMUM200 (7.9)FLAMMABILITY SELF-EXTINGUISHING WITHIN ONE MINUTE AND NO MORE THAN 25 PERCENT OF INDICATOR FLAG BURNEDOR CHARRED5.14 PROCEDURE B ASTM D2671FUNGUS RESISTANCEPROPERTIES AFTER:TENSILE STRENGT
22、H, PSI (MPA), MINIMUMULTIMATE ELONGATION,PERCENT, MINIMUMDIELECTRIC STRENGTH,VOLTS/MIL (KV/MM), MINIMUMRATING LESS THAN 1OR1700 (11.7)250300 (11.9) UP TO AN “AS SUPPLIED ID” OF 0.500200 (7.9) AN “AS SUPPLIED ID” OF 0.500 AND ABOVE5.17 ASTM G215.17 ISO 8461/ UNLESS OTHERWISE SPECIFIED, REQUIREMENTS,
23、TEST PROCEDURES AND CONDITIONS ARE FOR ALL CLASSES.AEROSPACE STANDARD AS23053/16SHEET 4 OF 4INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, CROSSLINKED, ELASTOMERICPOLYOLEFIN, FLEXIBLEAPPLICATION NOTES1. INTENDED USE: HEAT SHRINKABLE FLEXIBLE ELASTOMERIC SLEEVING IS INTENDED FOR USE ON HEAVY DUTY C
24、ABLES OR HARNESS SYSTEMS, SUCH AS GROUND SUPPORT WHICH SEE HIGH LEVELS OF PHYSICAL ABUSE AND EXPOSURE TO FUELS AND OILS, COUPLED WITH HIGH AND LOW TEMPERATURE EXTREMES.SPECIFICATION NOTES1. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING
25、 AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT,INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
