1、 AEROSPACE STANDARD STRAPS, CLAMPS, AND MOUNTING HARDWARE, PLASTIC FOR CABLE HARNESS TYING AND SUPPORT CLAMP, LOOP, NYLON, ADJUSTABLE, WIRE SUPPORT, TYPE III, CLASS 1AS23190/1Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval sy
2、stem or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServi
3、cesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1999-05REAFFIRMED 2012-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 FEDERAL SUPPLY CLASS 5340 AS23190/1SHEET 1 OF 5 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences.
4、 Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabil
5、ized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS23190/1 RATIONALE AS23190/1 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICETHIS DOCUM
6、ENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-S-23190/1A AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-S-23190/
7、1A. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFIC
8、ATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND P
9、ROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under
10、license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS23190/1SHEET 2 OF 5 STRAPS, CLAMPS, AND MOUNTING HARDWARE, PLASTIC FOR CABLE HARNESS TYING AND SUPPORT CLAMP, LOOP, NYLON, ADJUSTABLE, WIRE SUPPORT, TYPE III, CLASS 1 THE COMPLETE
11、REQUIREMENTS FOR PROCURING THE CLAMP DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE ISSUE IN EFFECT OF SPECIFICATION MIL-S-23190.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STA
12、NDARD AS23190/1SHEET 3 OF 5 STRAPS, CLAMPS, AND MOUNTING HARDWARE, PLASTIC FOR CABLE HARNESS TYING AND SUPPORT CLAMP, LOOP, NYLON, ADJUSTABLE, WIRE SUPPORT, TYPE III, CLASS 1 TABLE 1FIGURE 2 - TYPICAL ATTACHMENTCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reprod
13、uction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS23190/1SHEET 4 OF 5 STRAPS, CLAMPS, AND MOUNTING HARDWARE, PLASTIC FOR CABLE HARNESS TYING AND SUPPORT CLAMP, LOOP, NYLON, ADJUSTABLE, WIRE SUPPORT, TYPE III, CLASS 1 TABLE 2TEST FIXTURE DATACopyright SAE International
14、Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS23190/1SHEET 5 OF 5 STRAPS, CLAMPS, AND MOUNTING HARDWARE, PLASTIC FOR CABLE HARNESS TYING AND SUPPORT CLAMP, LOOP, NYLON, ADJUSTABLE, WIRE SUPPORT, TYPE III,
15、 CLASS 1 REQUIREMENTS:1. MATERIAL: NYLON, HEAT STABILIZED COMPOSITION, IN ACCORDANCE WITH MIL-M-20693, COMPOSITION A,TYPE I, COLOR: NATURAL.2. REMOVE ALL BURRS AND SHARP EDGES; BREAK ALL SHARP CORNERS. MOLD MARKS AND NORMAL VENTFLASH ARE PERMISSIBLE.3. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIE
16、D, TOLERANCES: FRACTIONS 1/32 DECIMALS .030 ANGLES 2.4. CONFIGURATION MAY VARY FROM THAT SHOWN PROVIDED DIMENSIONS REMAIN WITHIN TOLERANCE.5. PART NUMBER: THE PART NUMBER SHALL CONSIST OF THE LETTER “M”, SPECIFICATION SHEET NUMBER,AND A DASH NUMBER FROM TABLE I.EXAMPLE OF PART NUMBER: M23190/1-16. T
17、ENSILE STRENGTH: TENSILE STRENGTH FOR ALL DASH NUMBERS IS 50 POUNDS, WHICH IS THE MINIMUMTENSILE STRENGTH OF THE LARGEST PLASTIC TIEDOWN STRAP USABLE WITH THE CLAMP.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
