1、AEROSPACE STANDARD TERMINAL, LUG, FLAG TYPE, CRIMP STYLE, COPPER, CLASS I AS25189Copyright 2008 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, record
2、ing, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2008-07THIRD ANGLE PROJECTION CUSTODIAN: SAE
3、AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5940 AS25189SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS7928SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences. Theuse of thisreport is entirely voluntary, andits applicabilityandsuit
4、ability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled. SAE invites yourwritten commentsandsuggestions. NOTICE THIS DO
5、CUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS25189(ASG), NOTICE 2 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE M
6、S25189(ASG), NOTICE 2. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF
7、 GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF D
8、EFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT. Copyright SAE International Provid
9、ed by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD TERMINAL, LUG, FLAG TYPE, CRIMP STYLE, COPPER, CLASS I AS25189SHEET 2 OF 3FOR DESIGN FEATURE PURPOSES, THIS STANDARD TAKES PRECEDENCE OVER PROCUREMENT DOCUMENTS REFER
10、ENCED HEREIN.REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BID. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD TERMINAL, LUG, FLAG TYPE, CRIMP ST
11、YLE, COPPER, CLASS I AS25189SHEET 3 OF 3NOTES: B DIMENSION SHALL NOT EXCEED W DIMENSION. H DIMENSION SHALL NOT BE LESS THAN ONE HALF W MINIMUM DIMENSION. CHAMFER BOTH ENDS OF BARREL. CONTOUR OPTIONAL WITHIN DIMENSIONS NOTED. FINISH: TINNED PLATE. DIMENSIONS IN INCHES. THE SEAM OF THE BARREL SHALL BE
12、 PERMANENTLY SEALED AND SHALL NOT OPEN AS A RESULT OF THE CRIMPING OPERATION. MATERIAL: COPPER QQ-C-576 OR QQ-C-502. MIL-W-5086 WIRE SHALL BE USED FOR ALL QUALIFICATION TESTING WITH AN3427 CRIMPING TOOL. MS25189-1 THRU -47 PART NUMBERS COVERED BY REVISION “B“ DATED 21 SEPTEMBER 1962 ARE CANCELLED AF
13、TER 28 FEBRUARY 1969. INTERCHANGEABILITY RELATIONSHIP: PART NUMBERS MS25189-101 THRU -147 CAN REPLACE MS25189-1 THRU -47 PARTS RESPECTIVELY. THE CANCELLED MS25189-1 THRU -47 PARTS CANNOT ALWAYS REPLACE THE MS25189-101 THRU -147 PARTS. THE CANCELLED PARTS MAY BE USED UNTIL 28 FEBRUARY 1969 OR UNTIL A NEW QPL IS ESTABLISHED FOR MIL-T-7928F WHICHEVER COMES LATER. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
