1、AEROSPACE STANDARDHYDROCARBON FUELRESISTANT, TUBE FITTING, O-RING MOLDEDFROM AMS-P-5315 RUBBERAS29512Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, p
2、hotocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2001-03REVISED2016-10THIRD
3、ANGLE PROJECTIONCUSTODIAN: A-6/A-6C2REV. CFEDERAL SUPPLY CLASS5331AS29512SHEET 1 OF 4REV.CPROCUREMENT SPECIFICATION: NONESAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportis entirely voluntary, an
4、d its applicability and suitability forany particularuse, includingany patent infringement arising therefrom,is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleast every five years at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your written com
5、ments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS29512CRATIONALETHIS STANDARD HAS BEEN REVISED TO INCORPORATE MINOR TECHNICAL CHANGES.FOREWORDTHIS STANDARD ESTABLISHES THE DIMENSIONAL AND VISUAL QUALITY REQUIREMENTS, LO
6、T REQUIREMENTS AND PACKAGING AND LABELING REQUIREMENTS FOR O-RINGS MOLDED FROM AMS-P-5315 RUBBER. IT SHALL BE USED FOR PROCUREMENT PURPOSES.NOTE: DIMENSION AND TOLERANCING PER ASME Y14.5FIGURE 1 - O-RING - WIDTH (W) AND INSIDE (D) DIAMETERS AEROSPACE STANDARD AS29512SHEET 2 OF 4REV.CHYDROCARBON FUEL
7、RESISTANT, TUBE FITTING, O-RING MOLDEDFROM AMS-P-5315 RUBBERTABLE 1 - PART NUMBERS AND DIMENSIONSPARTNUMBERNOMINAL TUBEOUTSIDE DIAMETER D W APPROX. MASS(IN) (MM) (IN) (MM) (IN) (MM) (LB/100) (KG/100)MS29512-01 .094 2.381 .180 / .190 4.572 / 4.826 .053 / .059 1.346 / 1.499 .009 0.004MS29512-02 .125 3
8、175 .234 / .244 5.944 / 6.198 .061 / .067 1.549 / 1.702 .014 0.007MS29512-03 .188 4.775 .295 / .306 7.493 / 7.772 .061 / .067 1.549 / 1.702 .017 0.009MS29512-04 .250 6.350 .346 / .356 8.788 / 9.042 .069 / .075 1.753 / 1.905 .025 0.011MS29512-05 .313 7.950 .409 / .419 10.389 / 10.643 .069 / .075 1.7
9、53 / 1.905 .029 0.013.MS29512-06 .375 9.525 .463 / .473 11.760 / 12.014 .075 / .081 1.905 / 2.057 .038 0.017MS29512-07 .438 11.113 .525 / .535 13.335 / 13.589 .079 / .085 2.007 / 2.159 .047 0.021MS29512-08 .500 12.700 .639 / .649 16.231 / 16.485 .084 / .090 2.134 / 2.286 .063 0.028MS29512-09 .563 14
10、288 .701 / .711 17.805 / 18.059 .094 / .100 2.388 / 2.540 .086 0.039MS29512-10 .625 15.875 .750 / .760 19.050 / 19.304 .094 / .100 2.388 / 2.540 .091 0.041MS29512-11 .688 17.463 .858 / .868 21.793 / 22.047 .112 / .120 2.845 / 3.048 .150 0.068MS29512-12 .750 19.050 .918 / .930 23.317 / 23.622 .112 /
11、 .120 2.845 / 3.048 .158 0.076MS29512-13 .813 20.638 .980 / .992 24.892 / 25.197 .112 / .120 2.845 / 3.048 .168 0.080MS29512-14 .875 22.225 1.041 / 1.053 26.441 / 26.746 .112 / .120 2.845 / 3.048 .178 0.080MS29512-16 1.000 25.400 1.165 / 1.177 29.591 / 29.896 .112 / .120 2.845 / 3.048 .196 0.088MS29
12、512-18 1.125 28.575 1.349 / 1.361 34.265 / 34.569 .112 / .120 2.845 / 3.048 .225 0.101MS29512-20 1.250 31.750 1.465 / 1.485 37.211/ 37.719 .114 / .122 2.896 / 3.099 .252 0.113MS29512-24 1.500 38.100 1.710 / 1.730 43.434 / 43.942 .114 / .122 2.896 / 3.099 .290 0.131MS29512-28 1.750 44.450 2.080 / 2.1
13、00 52.832 / 53.340 .114 / .122 2.896 / 3.099 .349 0.157MS29512-32 2.000 50.800 2.327 / 2.347 59.106 / 59.614 .114 / .122 2.896 / 3.099 .388 0.1751. APPLICATIONTHESE O-RINGS TYPICALLY HAVE BEEN USED WHERE RESISTANCE TO FUEL IS REQUIRED, BUT USAGE IS NOT LIMITED TO SUCH APPLICATIONS. EACH APPLICATION
14、SHOULD BE CONSIDERED SEPARATELY. THESE O-RINGS HAVE A SERVICE TEMPERATURE RANGE OF -65 TO +180 q F (-54 TO +82 q C).2. APPLICABLE REFERENCES2.1 SAE PUBLICATIONSAVAILABLE FROM SAE INTERNATIONAL, 400 COMMONWEALTH DRIVE, WARRENDALE, PA 15096-0001, TEL: 877-606-7323 (INSIDE USA AND CANADA) OR +1 724-776
15、4970 (OUTSIDE USA), www.sae.org.AMS-P-5315 ACRYLONITRILE-BUTADIENE (NBR) RUBBER FOR FUEL-RESISTANT SEALS 60 TO 70AMS2817 PACKAGING AND IDENTIFICATION PREFORMED PACKINGSARP5316 STORAGE OF ELASTOMER SEALS AND SEAL ASSEMBLIES WHICH INCLUDE AN ELASTOMER ELEMENT PRIOR TO HARDWARE ASSEMBLY 2.2 ASME PUBLI
16、CATIONSAVAILABLE FROM ASME, P.O. BOX 2900, 22 LAW DRIVE, FAIRFIELD, NJ 07007-2900, TEL: 800-843-2763 (U.S./CANADA), 001-800-843-2763 (MEXICO), 973-882-1170 (OUTSIDE NORTH AMERICA), www.asme.org.ASME Y14.5-2009 DIMENSIONING AND TOLERANCINGAEROSPACE STANDARD AS29512SHEET 3 OF 4REV.CHYDROCARBON FUELRES
17、ISTANT, TUBE FITTING, O-RING MOLDEDFROM AMS-P-5315 RUBBER2.3 ASQ PUBLICATIONSAVAILABLE FROM AMERICAN SOCIETY FOR QUALITY, 600 NORTH PLANKINTON AVENUE, MILWAUKEE, WI 53203, TEL: 800-248-1946 (UNITED STATES OR CANADA), 001-800-514-1564 (MEXICO) OR +1-414-272-8575 (ALL OTHER LOCATIONS), www.asq.org.ANS
18、I/ASQ Z1.4 SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES2.4. ISO PUBLICATIONSCOPIES OF THESE DOCUMENTS ARE AVAILABLE ONLINE AT http:/webstore.ansi.org/.ISO 3601-1 FLUID POWER SYSTEMS - O-RINGS - PART 1: INSIDE DIAMETERS, CROSS-SECTIONS, TOLERANCES AND DESIGNATION CODESISO 3601-3 FLUID
19、POWER SYSTEMS - O-RINGS - PART 3: QUALITY ACCEPTANCE CRITERIA3. REQUIREMENTS3.1. PART NUMBER: THE O-RING PART NUMBERS ARE DESIGNATED MS29512-XX, WHERE XX INDICATES THE DASH SIZE.3.2 DO NOT USE UNASSIGNED PART NUMBERS.3.3 MATERIAL: THE MATERIAL SHALL BE IN ACCORDANCE WITH AMS-P-5315.3.4 DIMENSIONAL A
20、ND VISUAL INSPECTION: PRIOR TO INSPECTION, MOLD FLASH SHALL BE REMOVED FROM THE O-RINGS INSUCH A MANNER THAT THEY CONFORM TO THE REQUIREMENTS SPECIFIED HEREIN. FOR END OF PROCESS INSPECTION,EACH INDIVIDUAL O-RING (100%) SHALL BE VISUALLY INSPECTED AT 1X MAGNIFICATION FOR MOLD FLASH, BACKRIND, PARTIN
21、G LINE PROJECTION, NON-FILLS, FLOW LINES, AND OTHER SIGNIFICANT DEFECTS. THE ENTIRE O-RING SURFACESHALL BE INSPECTED.3.5 FOR FINAL INSPECTION, THE SAMPLE SIZE SHALL BE IN ACCORDANCE WITH ANSI/ASQ Z1.4 SINGLE SAMPLING PLAN INSPECTION LEVEL II WITH AN AQL 1.0 EXCEPT THAT THE ACCEPTANCE NUMBER SHALL BE
22、 ZERO.THE SAMPLE UNIT SHALL BE ONE O-RING. INSPECTION SHALL BE ACCORDING TO ISO 3601-3, GRADE S REQUIREMENTS UNDER 2X MAGNIFICATION. IN CASE OF DISAGREEMENT, THE VISUAL INSPECTION AT 2X MAGNIFICATION SHALL GOVERN.THE ENTIRE O-RING SURFACE SHALL BE MANUALLY INSPECTED. THE PROCEDURES OUTLINED IN ANNEX
23、 B OF ISO 3601-1SHALL BE FOLLOWED FOR DIMENSIONAL INSPECTION. IF THE PURCHASER REQUIRES A DIFFERENT SAMPLING PLAN ORVISUAL INSPECTION CRITERIA, MANUFACTURER SHALL BE INFORMED PRIOR TO TIME OF ORDER.3.6 THE MANUFACTURER OF THE O-RINGS SHALL BE RESPONSIBLE FOR THE REQUIRED INSPECTIONS. PURCHASER RESER
24、VES THE RIGHT TO SAMPLE AND PERFORM ANY CONFIRMATORY INSPECTION DEEMED NECESSARY TO ENSURE THAT THE O-RINGS CONFORM TO THE SPECIFIED REQUIREMENTS.3.7 LOT ACCEPTANCE: THE REQUIREMENTS ARE LISTED IN AMS-P-5315. THE LOT CERTIFICATION REPORT SHALL BE FURNISHED TO THE PURCHASER WHEN THE PRODUCT IS SHIPPE
25、D. THE MANUFACTURER OF THE O-RINGS SHALL BERESPONSIBLE FOR THE REQUIRED INSPECTIONS AND LOT ACCEPTANCE TESTS. PURCHASER RESERVES THE RIGHT TO SAMPLE AND PERFORM ANY CONFIRMATORY INSPECTION DEEMED NECESSARY TO ENSURE THAT THE O-RINGS CONFORM TO THE SPECIFIED REQUIREMENTS.3.8 IDENTIFICATION AND PACKAG
26、ING: PACKAGING SHALL BE IN ACCORDANCE WITH AMS2817 WITH THE EXCEPTION THAT, IF REQUESTED BY CONTRACT, EACH PACKAGE SHALL ALSO BEAR THE FOLLOWING IDENTIFICATION OF A RECOGNIZABLE SIZE:x NATIONAL STOCK NUMBER3.9 PURCHASE DOCUMENTS SHOULD SPECIFY NOT LESS THAN THE FOLLOWING:x AMS-P-5315 MATERIALx PART
27、NUMBER OF O-RING PER AS29512 x QUANTITY OF O-RINGS DESIREDx SPECIAL PACKAGING, LABELING, AND INSPECTION REQUIREMENTS, IF REQUIRED3.10 SHELF LIFE REQUIREMENTS OF ARP5316 APPLY TO THESE O-RINGS.AEROSPACE STANDARD AS29512SHEET 4 OF 4REV.CHYDROCARBON FUELRESISTANT, TUBE FITTING, O-RING MOLDEDFROM AMS-P-
28、5315 RUBBER3.11 DIMENSIONS AND PROPERTIES IN INCH UNITS ARE PRIMARY. DIMENSIONS AND PROPERTIES IN SI UNITS ARE SHOWN AS THE APPROXIMATE EQUIVALENTS OF THE PRIMARY UNITS AND ARE PRESENTED ONLY FOR INFORMATION.4. NOTES4.1 SEE MS21344 FOR INSTALLATION DETAILS.4.2 REVISION INDICATOR: A CHANGE BAR (I) LO
29、CATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
