1、 AEROSPACE STANDARD CONNECTOR, RECEPTACLE, ELECTRIC, POTTING SEAL, SOLDER CONTACT AN TYPE AS31031Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, phot
2、ocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-06 REAFFIRMED2016-10 R
3、EVISED2017-08THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.BFEDERAL SUPPLY CLASS 5935 AS31031 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS50151 SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicaland engineering sciences.The use ofthisrepo
4、rtisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaffirmed,stabilized,orcancelled.SAEinvitesyourwritten commen
5、tsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS31031B RATIONALE REVISION IS REQUIRED TO CORRECT THE PART NUMBER; THE DASHES WERE INADVERTENTLY REMOVED AT THE LAST REVISION. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING TH
6、E PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS50151. CLASS P ENVIRONMENT RESISTENT, POTTING FIGURE 1A CONNECTOR CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS31031 SHEET 2 OF 3 REV. B CONNECTOR, RECEPTACLE, ELECTRIC, POTTING SEAL, SOLDER CONTACT AN TYPE CLAS
7、S P ENVIRONMENT RESISTENT, POTTING FIGURE 1B CONNECTOR CONFIGURATION AND DIMENSIONS TABLE 1 FIGURE 1 DIMENSIONS SIZE A COUPLING THREAD B MIN USABLE THREAD D +.015 -.000 ID I MAX INSERT DIA J +.031 -.00 INT. SHELL SHLDR. K THICKNESS MOUNTING FLANGE L MAX OVERALL LENGTH M +.031 -.000 MOUNTING FLANGE L
8、OCATION MAX MIN 8S 1/2 - 28 .375 .370 .250 .562 .156 .062 1.531 .562 10S 5/8 - 24 .448 .320 10SL .448 12S 3/4 - 20 .557 12 .625 .750 1.968 .750 14S 7/8 - 20 .375 .682 .525 .562 1.531 .562 14 .625 .750 1.968 .750 16S 1 - 20 .375 .807 .650 .562 1.531 .562 16 .625 .750 1.968 .750 18 1-1/8 - 18 .932 .77
9、0 .203 .094 20 1-1/4 - 18 1.058 .925 2.188 22 1-3/8 - 18 1.182 1.020 24 1-1/2 - 18 1.307 1.145 .812 28 1-3/4 - 18 1.526 1.365 32 2 - 18 1.776 1.615 .359 .125 .875 36 2-1/4 - 16 1.995 1.830 40 2-1/2 - 16 2.245 2.047 AEROSPACE STANDARD AS31031 SHEET 3 OF 3 REV. B CONNECTOR, RECEPTACLE, ELECTRIC, POTTI
10、NG SEAL, SOLDER CONTACT AN TYPE TABLE 1 FIGURE 1 DIMENSIONS (CONTINUED) SIZE N MAX OD O (REF) MOUNTING HOLE DIA P +.015 -.000 KEY HEIGHT R .005 - MOUNTING HOLES S +.031 -.000 LENGTH SIDE T +.010 -.005 MOUNTING BOLT HOLE DIA U MIN 1/ V MAX DIA FOR INSERT ARRANGEMENT SEE DRAWING 8S .532 .635 .130 .594
11、 .875 .120 .085 .613 MIL-STD 1651 10S .656 .728 .165 .719 1.000 .707 10SL .863 12S .782 .885 .224 .812 1.094 12 .141 14S .906 .963 .263 .906 1.188 .085 .941 14 .141 16S 1.032 1.088 .325 .969 1.281 .085 1.066 16 .141 18 1.156 1.228 .385 1.062 1.375 1.207 20 1.282 1.353 .463 1.156 1.500 1.332 22 1.406
12、 1.478 .510 1.250 1.625 1.457 24 1.532 1.604 .573 1.375 1.750 .147 .226 1.582 28 1.782 1.854 .683 1.562 2.000 1.832 32 2.032 2.132 .808 1.750 2.250 .173 2.110 36 2.282 2.417 .915 1.938 2.500 2.395 40 2.532 2.616 1.023 2.188 2.750 2.594 1/ THE SURFACE WITHIN THE “U“ DIMENSION SHALL HAVE SURFACE IRREG
13、ULARITIES TO ASSIST THE GRIP OF THE POTTING COMPOUND TO THE SHELL. REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENTS AND THE LATEST ISSUE OF AS50151. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2 AND TABLE 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIF
14、IED, TOLERANCES ARE .015 INCH. 2. THE PART NUMBER SHALL BE AS SHOWN IN THE EXAMPLE BELOW: MS3103 - 18 - 5 S Y BASIC PART NUMBER SIZE INSERT ARRANGEMENT STYLE (P OR S) ALTERNATE INSERT POSITION (W, X, Y OR Z) LEAVE BLANK FOR NORMAL POSITION SPECIFICATION NOTES 1. REVISION INDICATOR: A CHANGE BAR (|)
15、LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPLICATION NOTES 1. AS31031 IS NOT RECOMMENDED FOR NEW DESIGN.
