1、AEROSPACE STANDARD PLUG, EXPANSION - CRES, 416 OR 416SE, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS S41600/UNS S41623 AS3127Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
2、electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUE
3、D 1981-02REAFFIRMED 2006-05 REVISED 2014-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5315 AS3127SHEET 1 OF 3REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering scien
4、ces. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, st
5、abilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3127BRATIONALE THIS IS A LIMITED SCOPE REVISION. REVISED CLEANING REQUIREMENTS (NOTE 3) FOR CONFORMANCE TO A
6、MS2700 OR ASTM A967/A967M. FIGURE 1 TABLE 1A PART NUMBERS AND DIMENSIONS STANDARD DIAMETER AEROSPACE STANDARD PART NUMBER /8/MANUFACTURERS PART NUMBER /8/A APPROX MASSLB/100 AS3127-01 PLGA0935020A .0928-.0937 .011 AS3127-02 PLGA1255020 A .1241-.1250 .022 AS3127-03 PLGA1565020 A .1553-.1562 .040 AS31
7、27-04 PLGA1875020 A .1866-.1875 .056 AS3127-05 PLGA2185020 A .2178-.2187 .088 AS3127-06 PLGA2505020 A .2491-.2500 .129 AS3127-07 PLGA2815020 A .2803-.2812 .178 AS3127-08 PLGA3435020 A .3428-.3437 .289 AS3127-09 PLGA4065020 A .4053-.4062 .462 AS3127-10 PLGA4685020 A .4678-.4687 .568 AS3127-11 PLGA531
8、5020 A .5303-.5312 .986 AS3127-12 PLGA6565020 A .6553-.6562 1.675AEROSPACE STANDARD AS3127SHEET 2 OF 3REV. BPLUG, EXPANSION - CRES, 416 OR 416SE, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS S41600/UNS S41623 TABLE 1B PART NUMBERS AND DIMENSIONS .010 OVERSIZE DIAMETER AEROSPACE STANDARD PART NUMBER /
9、8/MANUFACTURERS PART NUMBER /8/A APPROX MASSLB/100 AS3127-51 PLGA1035020A .1028-.1037 .013 AS3127-52 PLGA1355020 A .1341-.1350 .029 AS3127-53 PLGA1665020 A .1653-.1662 .047 AS3127-54 PLGA1975020 A .1966-.1975 .068 AS3127-55 PLGA2285020 A .2278-.2287 .108 AS3127-56 PLGA2605020 A .2591-.2600 .150 AS31
10、27-57 PLGA2915020 A .2903-.2912 .203 AS3127-58 PLGA3535020 A .3528-.3537 .329 AS3127-59 PLGA4165020 A .4153-.4162 .527 AS3127-60 PLGA4785020 A .4778-.4787 .645 AS3127-61 PLGA5415020 A .5403-.5412 1.080AS3127-62 PLGA6665020 A .6653-.6662 1.863 TABLE 1C PART NUMBERS AND DIMENSIONSAEROSPACE STANDARD PA
11、RT NUMBER /8/B NOM CNOM DE NOM FGNOM HAS3127-01 STD AND .010 OVERSIZE DIAMETERS, UNS S41600/UNS S41623 7. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCE: ANGULAR DIMENSIONS 2 DEGREES. DIMENSIONS APPLY AFTER FINISH. /8/ MARK AS3127-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE
12、 IN ACCORDANCE WITH AS478, METHOD 37. IN ADDITION PACKAGES FOR OVERSIZE PLUGS SHALL INCLUDE “OVERSIZE 416 SS” IN A RECTANGULAR BLOCK. 9. USE WITH AS3128 PINS. SEE AIR3276 HOLE PREPARATION AND AIR3277 INSTALLATION PROCEDURES. 10. DIMENSIONING AND TOLERANCING: PER ASME Y14.5M-1994. 11. DO NOT USE UNAS
13、SIGNED PART NUMBERS. 12. SEE AS3585 FOR PLUG AND PIN SET OF PARTS. 13. AS, AIR, AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION. 14. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIEN
14、CE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN
15、ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS
16、 SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING.
