1、AEROSPACE STANDARD PLUG, EXPANSION - CRES, 303, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS S30300 AS3131Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanic
2、al, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1981-02REAFFIRMED
3、2006-05 REVISED 2014-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5315 AS3131SHEET 1 OF 3REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis r
4、eport is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelle
5、d. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3131BRATIONALE THIS IS A LIMITED SCOPE REVISION. REVISED CLEANING REQUIREMENTS (NOTE 3) FOR CONFORMANCE TO AMS2700 OR ASTM A967/
6、A967M. FIGURE 1 TABLE 1A PART NUMBERS AND DIMENSIONS STANDARD DIAMETERS AEROSPACE STANDARD PART NUMBER /8/MANUFACTURERSPART NUMBER /8/A APPROX MASSLB/100 AS3131-01 PLGA0935030A .0928-.0937 .011 AS3131-02 PLGA1255030A .1241-.1250 .022 AS3131-03 PLGA1565030A .1553-.1562 .040 AS3131-04 PLGA1875030A .18
7、66-.1875 .056 AS3131-05 PLGA2185030A .2178-.2187 .088 AS3131-06 PLGA2505030A .2491-.2500 .129 AS3131-07 PLGA2815030A .2803-.2812 .178 AS3131-08 PLGA3435030A .3428-.3437 .289 AS3131-09 PLGA4065030A .4053-.4062 .462 AS3131-10 PLGA4685030A .4678-.4687 .568 AS3131-11 PLGA5315030A .5303-.5312 .986 AS3131
8、-12 PLGA6565030A .6553-.6562 1.675AEROSPACE STANDARD AS3131SHEET 2 OF 3REV. BPLUG, EXPANSION - CRES, 303, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS S30300 TABLE 1B PART NUMBERS AND DIMENSIONS .010 OVERSIZE DIAMETERS AEROSPACE STANDARD PART NUMBER /8/MANUFACTURERSPART NUMBER /8/A APPROX MASSLB/100
9、AS3131-51 PLGA1035030A .1028-.1037 .013 AS3131-52 PLGA1355030A .1341-.1350 .029 AS3131-53 PLGA1665030A .1653-.1662 .047 AS3131-54 PLGA1975030A .1966-.1975 .068 AS3131-55 PLGA2285030A .2278-.2287 .108 AS3131-56 PLGA2605030A .2591-.2600 .150 AS3131-57 PLGA2915030A .2903-.2912 .203 AS3131-58 PLGA353503
10、0A .3528-.3537 .329 AS3131-59 PLGA4165030A .4153-.4162 .527 AS3131-60 PLGA4785030 A .4778-.4787 .645 AS3131-61 PLGA5415030 A .5403-.5412 1.080AS3131-62 PLGA6665030 A .6653-.6662 1.863 TABLE 1C PART NUMBERS AND DIMENSIONS AEROSPACE STANDARD PART NUMBER /8/B NOM CNOM DE NOM FGNOM HAS3131-01 STD AND .0
11、10 OVERSIZE DIAMETERS, UNS S30300 6. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: ANGULAR DIMENSIONS 2 DEGREES. /8/ MARK AS3131-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE IN ACCORDANCE WITH AS478, METHOD 37. IN AD
12、DITION PACKAGES FOR OVERSIZE PLUGS SHALL INCLUDE “OVERSIZE 303SS” IN A RECTANGULAR BLOCK. 9. USE WITH AS3132 PINS. SEE AIR3276 HOLE PREPARATION AND AIR3277 INSTALLATION PROCEDURES. 10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. SEE AS3587 FOR PLUG AND
13、 PIN SET OF PARTS. 13. AS, AIR, AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. 14. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEE
14、N MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURC
15、E OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING.
