1、AEROSPACE STANDARD BOLT, MACHINE-DOUBLE HEX EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, CORROSION RESISTANT STEEL (UNS S17400), 140 KSI UTS MIN, .1900-32, UNJF-3AAS3167Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system o
2、r transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.
3、org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1976-03REAFFIRMED2006-10REVISED 2015-02THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS AS3167SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION AS7474 /8/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance
4、 thestate of technicalandengineeringsciences.The useofthis reportisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which
5、 time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3167ARATIONALE REVISE THREAD SPECIFICATION TO AS8879. REVISE LIGHTENING
6、HOLE CONFIGURATION (ADD SECTION VIEW) TO ALLOW OPTIONAL SHAPE AT BOTTOM OF HOLE, DELETE .015 MAX RADIUS AT BASE OF WRENCH PAD, UPDATE FPI REQUIREMENTS, ADD SURFACE FINISH REQUIREMENTS TO BOLT HEAD, REVISE COLD ROLLING NOTE, UPDATE TO ANSI Y14.5M-1982, DELETE METRIC DIMENSIONS, GENERAL EDITORIAL UPDA
7、TE, REFERENCES UDATED AND FIGURE 1 REDRAWN. FIGURE 1 - BOLT AEROSPACE STANDARD AS3167SHEET 2 OF 3REV. ABOLT, MACHINE - DOUBLE HEX EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, CORROSION RESISTANT STEEL (UNS S17400), 140 KSI UTS MIN, .1900-32, UNJF-3ATABLE 1 - PART NUMBERS AND DIMENSION PART NO. L GMI
8、NKMAXAPPROX. MASSLB/100 PART NO. L GMINKMAXAPPROX. MASSLB/100 AS3167-03 .597- .617 .126 .198 .87 AS3167-30 2.284-2.304 1.812 1.885 2.19 AS3167-04 .659- .679 .188 .260 .92 AS3167-31 2.347-2.367 1.876 1.948 2.24 AS3167-05 .721- .741 .250 .322 .96 AS3167-32 2.409-2.429 1.938 2.010 2.29 AS3167-06 .784-
9、.804 .312 .385 1.02 AS3167-33 2.471-2.491 2.000 2.072 2.33 AS3167-07 .847- .867 .376 .448 1.07 AS3167-34 2.534-2.554 2.062 2.135 2.39 AS3167-08 .909- .929 .438 .510 1.12 AS3167-35 2.597-2.617 2.126 2.198 2.44 AS3167-09 .971- .991 .500 .572 1.16 AS3167-36 2.659-2.679 2.188 2.260 2.49 AS3167-10 1.034-
10、1.054 .562 .635 1.21 AS3167-37 2.721-2.741 2.250 2.322 2.53 AS3167-11 1.097-1.117 .626 .698 1.26 AS3167-38 2.784-2.804 2.312 2.385 2.59 AS3167-12 1.159-1.179 .688 .760 1.30 AS3167-39 2.847-2.867 2.376 2.448 2.63 AS3167-13 1.221-1.241 .750 .822 1.36 AS3167-40 2.909-2.929 2.438 2.510 2.68 AS3167-14 1.
11、284-1.304 .812 .885 1.41 AS3167-41 2.971-2.991 2.500 2.572 2.73 AS3167-15 1.347-1.367 .876 .948 1.46 AS3167-42 3.034-3.054 2.562 2.635 2.78 AS3167-16 1.409-1.429 .938 1.010 1.50 AS3167-43 3.097-3.117 2.626 2.698 2.83 AS3167-17 1.471-1.491 1.000 1.072 1.55 AS3167-44 3.159-3.179 2.688 2.760 2.87 AS316
12、7-18 1.534-1.554 1.062 1.135 1.61 AS3167-45 3.221-3.241 2.750 2.822 2.92 AS3167-19 1.597-1.617 1.126 1.198 1.65 AS3167-46 3.284-3.304 2.812 2.885 2.98 AS3167-20 1.659-1.679 1.188 1.260 1.70 AS3167-47 3.347-3.367 2.876 2.948 3.02 AS3167-21 1.721-1.741 1.250 1.322 1.75 AS3167-48 3.409-3.429 2.938 3.01
13、0 3.07 AS3167-22 1.784-1.804 1.312 1.385 1.80 AS3167-49 3.471-3.491 3.000 3.072 3.12 AS3167-23 1.847-1.877 1.376 1.448 1.85 AS3167-50 3.534-3.554 3.062 3.135 3.18 AS3167-24 1.909-1.929 1.438 1.510 1.90 AS3167-51 3.597-3.617 3.126 3.198 3.22 AS3167-25 1.971-1.991 1.500 1.572 1.95 AS3167-52 3.659-3.67
14、9 3.188 3.260 3.27 AS3167-26 2.034-2.054 1.562 1.635 1.99 AS3167-53 3.721-3.741 3.250 3.322 3.32 AS3167-27 2.097-2.117 1.626 1.698 2.04 AS3167-54 3.784-3.804 3.312 3.385 3.36 AS3167-28 2.159-2.179 1.688 1.760 2.09 AS3167-55 3.847-3.867 3.376 3.448 3.41 AS3167-29 2.221-2.241 1.750 1.822 2.14 NOTES: /
15、1/ FOR PART NUMBERS AS3167-03 THRU AS3167-05 DATUM A SHALL REPLACE DATUM B.2. MATERIAL: AMS5643 (CORROSION RESISTANT STEEL, SIMILAR TO UNS S17400). 3. PROCUREMENT SPECIFICATION: AS7474. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SY
16、MBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra EXCEPT UPSET HEAD. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. AEROSPACE STANDARD AS3167SHEET 3 OF 3REV. ABOLT, MACHINE - DOUBLE HEX EXTENDED
17、WASHER HEAD, CLOSE TOLERANCE SHANK, CORROSION RESISTANT STEEL (UNS S17400), 140 KSI UTS MIN, .1900-32, UNJF-3A/8/ HEAD TO SHANK FILLET SHALL BE COLD ROLLED PER AS7474 AFTER HEAT TREATMENT. THE COLD ROLLING SHALL BE SUFFICIENT TO REMOVE ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS EXCEPT THAT DISTOR
18、TIONS AT LOCATION “A” IN FIGURE 2 OF AS7474 SHALL NOT BE PERMITTED ON THE HEAD BEARING AREA AND SHALL BE PERMITTED ON THE SHANK DIAMETER ONLY IF THE DISTORTION DOES NOT CAUSE THE SHANK DIAMETER TO EXCEED .1900 DIAMETER. 9. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION). 10. DO NOT
19、 USE UNASSIGNED PART NUMBERS. 11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMP
20、LETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
