1、 AEROSPACE STANDARD BOLT, MACHINE DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, NICKEL ALLOY, UNS N07718, 185 KSI MIN, .5625-18 UNJF-3A AS3242Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form
2、 or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:
3、/www.sae.org ISSUED 1980-07REAFFIRMED2007-06REVISED 2017-10THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.D FEDERAL SUPPLY CLASS 5306 AS3242 SHEET 1 OF 3 REV. D PROCUREMENT SPECIFICATION: AS7466 SAE Technical Standards Board Rules provide that: “This report ispublished by SAEtoadvance thestate of techni
4、calandengineering sciences. Theuse of thisreport is entirely voluntary, andits applicabilityand suitability forany particular use, including any patent infringement arisingtherefrom, isthesole responsibility of theuser.”SAE reviews eachtechnicalreport at least everyfive years at which timeitmay bere
5、vised, reaffirmed, stabilized, orcancelled. SAE invitesyourwrittencomments andsuggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS3242D RATIONALE DELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE, REVISE LEAD IN CHAMFER T
6、O CONFORM TO AS1132, ADD NEW INVENTORY DISPOSITION NOTE, UPDATE FPI REQUIREMENTS, UPDATE REFERENCES, AND GENERAL EDITORIAL UPDATE TO FIGURE 1. FIGURE 1 - BOLT AEROSPACE STANDARD AS3242 SHEET 2 OF 3 REV. D BOLT, MACHINE DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, NICKEL ALLOY, UNS N07718, 185 KSI
7、MIN, .5625-18 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NO. L N MIN M MAX APPROX MASS LB/100 PART NO. L N MIN M MAX APPROX MASS LB/100 AS3242-04 .865- .885 .030 .133 11.03 AS3242-31 3.115-3.135 1.579 1.750 25.60 AS3242-05 .928- .948 .030 .133 11.44 AS3242-32 3.240-3.260 1.704 1.875 26.41 AS
8、3242-06 .990-1.010 .030 .133 11.84 AS3242-33 3.365-3.385 1.829 2.000 27.22 AS3242-07 1.052-1.072 .030 .133 12.25 AS3242-34 3.490-3.510 1.954 2.125 28.03 AS3242-08 1.115-1.135 .030 .133 12.65 AS3242-35 3.615-3.635 2.079 2.250 28.84 AS3242-09 1.178-1.198 .030 .133 13.06 AS3242-36 3.740-3.760 2.204 2.3
9、75 29.64 AS3242-10 1.240-1.260 .030 .133 13.46 AS3242-37 3.865-3.885 2.329 2.500 30.46 AS3242-11 1.302-1.322 .030 .133 13.87 AS3242-38 3.990-4.010 2.454 2.625 31.27 AS3242-12 1.365-1.385 .030 .133 14.27 AS3242-39 4.115-4.135 2.579 2.750 32.07 AS3242-13 1.428-1.448 .030 .133 14.68 AS3242-40 4.240-4.2
10、60 2.704 2.875 32.88 AS3242-14 1.490-1.510 .030 .133 15.08 AS3242-41 4.365-4.385 2.829 3.000 33.69 AS3242-15 1.552-1.572 .030 .188 15.49 AS3242-42 4.490-4.510 2.954 3.125 34.50 AS3242-16 1.615-1.635 .079 .250 15.89 AS3242-43 4.615-4.635 3.079 3.250 35.31 AS3242-17 1.678-1.698 .142 .312 16.30 AS3242-
11、44 4.740-4.760 3.204 3.375 36.12 AS3242-18 1.740-1.760 .204 .375 16.70 AS3242-45 4.865-4.885 3.329 3.500 36.93 AS3242-19 1.802-1.822 .266 .438 17.11 AS3242-46 4.990-5.010 3.454 3.625 37.74 AS3242-20 1.865-1.885 .329 .500 17.51 AS3242-47 5.115-5.135 3.579 3.750 38.55 AS3242-21 1.928-1.948 .392 .562 1
12、7.92 AS3242-48 5.240-5.260 3.704 3.875 39.36 AS3242-22 1.990-2.010 .454 .625 18.32 AS3242-49 5.365-5.385 3.829 4.000 40.17 AS3242-23 2.115-2.135 .579 .750 19.13 AS3242-50 5.490-5.510 3.954 4.125 40.98 AS3242-24 2.240-2.260 .704 .875 19.94 AS3242-51 5.615-5.635 4.079 4.250 41.79 AS3242-25 2.365-2.385
13、 .829 1.000 20.75 AS3242-52 5.740-5.760 4.204 4.375 42.60 AS3242-26 2.490-2.510 .954 1.125 21.56 AS3242-53 5.865-5.885 4.329 4.500 43.41 AS3242-27 2.615-2.635 1.079 1.250 22.37 AS3242-54 5.990-6.010 4.454 4.625 44.22 AS3242-28 2.740-2.760 1.204 1.375 23.18 AS3242-29 2.865-2.885 1.329 1.500 23.99 AS3
14、242-30 2.990-3.010 1.454 1.625 24.80 NOTES /1/ FOR PART NUMBERS AS3242-04 THROUGH AS3242-24 DATUM Z (THREAD PD) SHALL REPLACE DATUM Y. 2. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY PER AMS5662 (UNS N07718). 3. PROCUREMENT SPECIFICATION: AS7466. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E
15、1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MINIMUM. 5. SURFACE TEXTURE: SYMBOLS ARE PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1 UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS ARE IN INCHES. 8. DIMENSIONING A
16、ND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 10. DO NOT USE UNASSIGNED PART NUMBERS. AEROSPACE STANDARD AS3242 SHEE
17、T 3 OF 3 REV. D BOLT, MACHINE DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, NICKEL ALLOY, UNS N07718, 185 KSI MIN, .5625-18 UNJF-3A 11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANG
18、ES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
