1、 AEROSPACE STANDARD INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SHELL SIZE 61 (FOR AS81703 CONNECTORS) AS33704Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mech
2、anical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-01THIRD A
3、NGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5970 AS33704 SHEET 1 OF 5 PROCUREMENT SPECIFICATION: AS81703SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary,
4、andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomme
5、nts andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS33704 RATIONALE AS33704 PERMITS THE CANCELLATION AND SUPERSESSION OF MS33704 WITH THIS DOCUMENT. FIGURE 1 - INSERT POSITION AEROSPACE STANDARD AS33704 SHEET 2
6、OF 5 INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SHELL SIZE 61 (FOR AS81703 CONNECTORS) TABLE 1 - APPLICABLE CONNECTORS APPLICABLE CONNECTORS (REFERENCE) RECEPTACLES PLUGS AS31341 AS34451AS31491 AS34461 AS34241 AS34671AS34641 NOTES: 1. DIMENSIONING IN ACCORDANCE WITH ANSI Y14.5. DIMENSIONS ARE IN INC
7、HES. APPLICABLE CONNECTORS ARE LISTED IN TABLE 1. 2. DIMENSIONS LOCATING CONTACTS AND INSERTS ARE TRUE POSITION. THE FOLLOWING TOLERANCES APPLY TO INSERT INSTALLED IN THE SHELL: a) CENTER OF EACH HOLE IN THE INSERT SHALL BE LOCATED AT TRUE POSITION WITHIN .020 DIAMETER. b) CENTER OF ENGAGING END OF
8、EACH CONTACT SHALL BE LOCATED AT TRUE POSITION WITH .027 DIAMETER. 3. DIMENSIONS AND MARKINGS SHOWN ARE FOR ENGAGING FACE OF PIN INSERT (SOCKET INSERT OPPOSITE). 4. UNLESS OTHERWISE INDICATED, DIMENSIONS ARE SYMETRICAL ABOUT CENTERLINES. 5. EACH INSERT ARRANGEMENT IS SHOWN IN ITS NORMAL POSITION IN
9、THE SHELL. 6. IN NORMAL POSITION, THE INDEXING RADIUS COINCIDES WITH THE CENTER LINE OF THE MASTER KEY OR KEYWAY OF THE SHELL. 7. IN ALTERNATE POSITIONS, THE SOCKET INSERT IS ROTATED COUNTERCLOCKWISSE SO THAT ANGLE “OC” BETWEEN THE INDEXING RADIUS AND THE CENTER LINE OF THE MASTER KEY OR KEYWAY OF S
10、HELL IS AS REQUIRED. 8. THIS IS A DESIGN STANDARD, NOT TO BE USED AS A PART NUMBER. FOR DESIGN FEATURE PURPOSES, THIS STANDARD TAKES PRECEDENCE OVER THE PROCUREMENT DOCUMENTS. AEROSPACE STANDARD AS33704 SHEET 3 OF 5 INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SHELL SIZE 61 (FOR AS81703 CONNECTORS) FI
11、GURE 2 - INSERT ARRANGEMENT 61-50 AEROSPACE STANDARD AS33704 SHEET 4 OF 5 INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SHELL SIZE 61 (FOR AS81703 CONNECTORS) TABLE 2 - INSERT 61-50 DETAILS CONTACT QUANTITY CONTACT SIZE SYMBOL SERVICE RATING 61 20 I TABLE 3 - INSERT 61-50 ALTERNATE INSERT POSITIONS ALT
12、ERNATE INSERT POSITIONS (OC DEGREES) W X Y B C - - 75 150 225 FIGURE 3 - INSERT ARRANGEMENT 61-42 AEROSPACE STANDARD AS33704 SHEET 5 OF 5 INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SHELL SIZE 61 (FOR AS81703 CONNECTORS) TABLE 4 - INSERT ARRANGEMENT 61-42 DETAILS CONTACT QUANTITY CONTACT SIZE SYMBOL
13、SERVICE RATING 4 16 I 29 20 8 12 TABLE 5 - INSERT 61-42 ALTERNATE INSERT POSITIONS ALTERNATE INSERT POSITIONS (OC DEGREES) W X Y B C - 67 30 - - - SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT E
14、DITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
