1、 AEROSPACE STANDARD BOLT, MACHINE - HEXAGON HEAD, DRILLED 1 HOLE, PD SHANK, AMS5708 (UNS N07001), .1900-32 UNJF-3A AS3400Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elec
2、tronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 19
3、85-08REAFFIRMED2006-05REVISED 2015-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.A FEDERAL SUPPLY CLASS 5306AS3400 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: AS7471SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering scien
4、ces. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabil
5、ized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3400A RATIONALE UPDATE THREAD SPECIFICATION TO AS8879, UPDATE TO ANSI Y14.5M-1982, REVISE FPI REQUIREMENTS TO AS
6、TM E1417/1417M, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING, REVISE ACROSS POINTS DIMENSION, ADD AS3062 FOR THREAD RUNOUT, FIGURE 1 REDRAWN, UPDATE REFERENCES, AND GENERAL EDITORIAL UPDATE. FIGURE 1 - BOLT AEROSPACE STANDARD AS3400 SHEET 2 OF 2 REV.A BOLT, MACHINE - HEXAGON HEAD, DRILLED 1 HOLE, PD
7、 SHANK, AMS5708 (UNS N07001), .1900-32 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NO. L G MIN K MAX APPROX. MASS LB/100 PART NO. L G MIN K MAX APPROX. MASS LB/100 AS3400-03 .302- .322 .025 .092 .66 AS3400-27 1.802-1.822 1.060 1.182 1.67 AS3400-04 .365- .385 .025 .092 .70 AS3400-28 1.865-1.88
8、5 1.123 1.245 1.71 AS3400-05 .428- .448 .025 .092 .74 AS3400-29 1.928-1.948 1.186 1.308 1.75 AS3400-06 .490- .510 .025 .092 .79 AS3400-30 1.990-2.010 1.248 1.370 1.79 AS3400-07 .552- .572 .025 .092 .83 AS3400-31 2.115-2.135 1.373 1.495 1.87 AS3400-08 .615- .635 .025 .092 .87 AS3400-32 2.240-2.260 1.
9、498 1.620 1.96 AS3400-09 .678- .698 .025 .092 .91 AS3400-33 2.365-2.385 1.623 1.745 2.04 AS3400-10 .740- .760 .025 .120 .95 AS3400-34 2.490-2.510 1.748 1.870 2.13 AS3400-11 .802- .822 .060 .183 .99 AS3400-35 2.615-2.635 1.873 1.995 2.21 AS3400-12 .865- .885 .123 .245 1.03 AS3400-36 2.740-2.760 1.998
10、 2.120 2.30 AS3400-13 .928- .948 .186 .308 1.08 AS3400-37 2.865-2.885 2.123 2.245 2.38 AS3400-14 .990-1.010 .248 .370 1.12 AS3400-38 2.990-3.010 2.248 2.370 2.46 AS3400-15 1.052-1.072 .310 .432 1.16 AS3400-39 3.115-3.135 2.373 2.495 2.55 AS3400-16 1.115-1.135 .373 .495 1.20 AS3400-40 3.240-3.260 2.4
11、98 2.620 2.63 AS3400-17 1.178-1.198 .436 .558 1.24 AS3400-41 3.365-3.385 2.623 2.745 2.72 AS3400-18 1.240-1.260 .498 .620 1.28 AS3400-42 3.490-3.510 2.748 2.870 2.80 AS3400-19 1.302-1.322 .560 .682 1.32 AS3400-43 3.615-3.635 2.873 2.995 2.89 AS3400-20 1.365-1.385 .623 .745 1.37 AS3400-44 3.740-3.760
12、 2.998 3.120 2.97 AS3400-21 1.428-1.448 .686 .808 1.41 AS3400-45 3.865-3.885 3.123 3.245 3.05 AS3400-22 1.490-1.510 .748 .870 1.45 AS3400-23 1.552-1.572 .810 .932 1.50 AS3400-24 1.615-1.635 .873 .995 1.54 AS3400-25 1.678-1.698 .936 1.058 1.59 AS3400-26 1.740-1.760 .998 1.120 1.62 NOTES: /1/ FOR PART
13、 NUMBERS AS3400-03 THRU AS3400-14 THE DATUM A SHALL REPLACE DATUM B. 2. MATERIAL: AMS5708 CORROSION AND HEAT RESISTANT NICKEL ALLOY (COMPOSITION SIMILAR TO UNS N07001). 3. PROCUREMENT SPECIFICATION: AS7471. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5
14、 SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLE
15、RANCES: ANGULAR DIMENSIONS 5. 8. DIMENSIONS AND TOLERANCING ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MAD
16、E TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
