1、 AEROSPACE STANDARD CONNECTOR, RECEPTACLE, ELECTRIC, CRIMP TYPE, WALL MOUNTING FLANGE, PUSH-PULL COUPLING, SERIES 3 (CLASS L AND E) AS34241Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or
2、by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www
3、sae.org ISSUED 2013-09REVISED 2014-12THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS34241SHEET 1 OF 7 REV. APROCUREMENT SPECIFICATION: AS81703SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineerin
4、g sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed,
5、 stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS34241ARATIONALE REVISION IS REQUIRED TO CORRECT THE OVERALL LENGTH (1.180 MAX.) LEFT SIDE DIMENSIONAL BOU
6、NDARY IN FIGURE 1. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81703. FIGURE 1 - CONNECTOR CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS34241SHEET 2 OF 7 REV. ACONNECTOR, RECEPTACLE, ELECTRIC, CRIMP TYPE, W
7、ALL MOUNTING FLANGE, PUSH-PULL COUPLING, SERIES 3 (CLASS L AND E) FIGURE 1A - CONNECTOR CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS34241SHEET 3 OF 7 REV. ACONNECTOR, RECEPTACLE, ELECTRIC, CRIMP TYPE, WALL MOUNTING FLANGE, PUSH-PULL COUPLING, SERIES 3 (CLASS L AND E) FIGURE 1B - CONNECTOR CONF
8、IGURATION AND DIMENSIONS DETAIL T FIGURE 1C - CONNECTOR CONFIGURATION AND DIMENSIONS FOR DETAIL S AND T *- REFERS TO OUTER ROW OF CONTACT CAVITIES (SEE CHART) AEROSPACE STANDARD AS34241SHEET 4 OF 7 REV. ACONNECTOR, RECEPTACLE, ELECTRIC, CRIMP TYPE, WALL MOUNTING FLANGE, PUSH-PULL COUPLING, SERIES 3
9、CLASS L AND E) TABLE 1 - INSERT ARRANGEMENTS REQUIRING REDUCED DIAMETERS INSERT ARRANGEMENTS REQUIRING REDUCED DIAMETERS FOR SOCKET CONTACT CHAMFER LEAD-IN AND PIN CONTACT RAISED SEAL BARRIERS SHELL SIZE INSERT ARRANGEMENTS CONTACT CAVITIES 12 12-50 5, 6, 8, 9, 11 ANGULAR TOLERANCE, X 1-0 AND XX 30
10、 THE .380/.368 DIMENSION (SEE FIGURE 1) CONTROLS BOTH THE LENGTH OF KEYWAY, FULL WIDTH, AND START OF ANGLE FROM “B“ DIA. RADIUS RUN-OUT OF KEYWAY PAST THE .380 MAXIMUM IS OPTIONAL AS LONG AS THERE IS NO DAMAGE TO THE CONNECTOR. KEYWAYS (MMC) AND INSERT SHALL BE LOCATED WITHIN .004 EITHER SIDE OF (T
11、P) RELATIVE TO MASTER KEY (MMC) AND SHELL O.D. (MMC). 2. COLOR BAND .100 WIDE MAXIMUM. BAND LOCATION MUST BE SUCH THAT IT IS VISIBLE WHEN CONNECTOR IS MOUNTED. 3. CONNECTOR ASSEMBLY MUST INCLUDE A BACKSHELL TO MEET THE MOISTURE SEALING REQUIREMENTS OF AS81703. SEE AS85049/31 (FORMERLY MS3416 STYLE E
12、), /60-2 (FORMERLY MS3416 STYLE G), /52-1 (FORMERLY MS 3417), AND /51-1 (FORMERLY MS3418) FOR BACKSHELL ACCESSORIES. 4. MATERIALS: SHELLS: 6061-T6 PER QQ-A-367. 5. THE FINISH ON THE SHELLS SHALL BE ELECTROLESS NICKEL. 6. PART NUMBER EXAMPLE MS3424 L 19 - 50 P B ALTERNATE INSERT POSITION CONTACT STYL
13、E INSERT ARRANGEMENT SHELL SIZE CLASS DETAIL SPECIFICATION PART NUMBER SPECIFICATION NOTE: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
